Jump to content

2014+ Lowering / Drop Kits

mjw930

By mjw930
in Modifications & Accessories

 Share

Recommended Posts

2005_Silverado New Member

2005_Silverado

Posted
Posted
1 minute ago, krzyd said:

I have a '14 Denali, I'm about ready to go from a 2" lift on 34" tires to a drop on Foose 22" rims and a supercharger. Looking for recommendations on the best drop kit/shock combo. Thanks in advance

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

  • Replies 3.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Heavy_Static
Heavy_Static

A few pics from last week:    

bakerrr
bakerrr

First post here Picked her about 2 weeks ago couldn't wait to start modifying it. Just installed Belltechs 4/7 drop this weekend It's low enough for the time being ??  

Nasty
Nasty

Posted Images

krzyd Enthusiast

krzyd

Posted
Posted
1 minute ago, 2005_Silverado said:

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.

 

FORGIVEN06 Enthusiast

FORGIVEN06

Posted
Posted
4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.
 


Aluminum a arms?


Sent from my iPhone using Tapatalk
  • 1 month later...
slee3247 Enthusiast

slee3247

Posted
Posted

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

  • Like 1
Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
12 hours ago, slee3247 said:

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, Stressin said:

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
8 minutes ago, slee3247 said:

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

I definitely want the extended range of travel for the diff, and I'm not too worried about resale...I haven't ever sold off any vehicle that I've owned, and don't intend on starting a new trend now either. If the time ever comes that I want to sell it and upgrade, then I fully expect to take whatever financial hit comes along with the modifications. Besides, I already have the feeling that I'm gonna want to go even lower at some point :)

 

I appreciate the heads up nonetheless!

  • Like 1
silvy2k17 Enthusiast

silvy2k17

Posted
Posted
On 12/19/2017 at 5:30 PM, Goinovr said:

4/6 Inez Hot Rods kit on 22x9.5 +25 305/45 tires.

truckwide.jpg

what wheels are those Goinovr? I like them a lot 

NoLand Enthusiast

NoLand

Posted
Posted
For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.
 
This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk

 

These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings

NoLand Enthusiast

NoLand

Posted
Posted
These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk

 

Can't honestly remember if there is a hole or not. If not, not a big deal to drill a 3/8" hole for a bolt. ?

blownZ71 Enthusiast

blownZ71

Posted
Posted
On 11/1/2017 at 9:42 PM, Derek66lsx said:

Couldn't resist any longer, it needed to be lower..

Im now at 2" front 5" rear drop, sits perfect, and the belltech shocks/struts ride 1000x better then the stock racho's 

just in time for winter, had to put the winter wheels on this weekend :(

gmc.JPG

I am in a similar position as you were. I have the rear leveled with the shackles but want to go lower. Is your front suspension steel or aluminum? As I have not really been able to find any solutions for an aluminum front A-arm setup on a 4x4. How did the alignment go on the front? Also, any rubbing of your 285's, or even close? My 305's barely rub at full lock so just wondering how bad that might get.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      A little girl said her prayers every night before bed and she asked G d to watch after each person she loved. One night she forgot to pray for her babysitter and her babysitter died. A few days later she forgot to pray for someone else and they died. The next night she forgot to pray for her dad. The next morning her dad was terrified. A bus almost crashed into him. He almost fell off a fifty foot ladder and almost wrecked on the way home. When he arrived home, he said I had a terrible day. His wife replied, “You think you had a bad day? My aerobics teacher died during class.
    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      Nice! I had one here, once. The car dealer I used to haul for stopped by with it. That was over 10 years ago now. Those are SUPER rare these days, especially up here! Never even see them at car shows anymore.   https://postimg.cc/0rvcNZ1W
    • KARNUT
      What did you do to your "other" car (aka musclecar) today

      By KARNUT · Posted

      I remember watching one of the auctions on TV. It just happened that they had two little red express trucks. My brother bought one new in 1979, still has it. So I hung on to watch them cross. The retro redone example brought more bids and went for more money than the original one did. My brother has redone his 3 times and raced it. He’s now in the process of making more tame for cruising. 
    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      I always upgraded the suspension and steering components - bushings and ball joints, and had older cars that I could out-corner ANY modern car with. I used to be able to take my '78 Cutlass on off-ramps at stupid speeds and make the sharp MA corners without even squealing the tires. So much fun. My '72 El Camino must've had work done by the previous owner, since that thing seemed to handle even better than the '78.   I think the suspension & steering on the '72 was much more advanced than the '64, so that probably just made a good system even better.   I'm the same way with vehicles. I hate having to worry about the paint on my '93 W250 Cummins. I'm not used to that, lol.   https://postimg.cc/mzKr55sY
    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      BEAUTIFUL!! That a Cutlass F85? Or 442? My side-ID skills are lacking thanks to failing memory, lol. Love that color & year, too!   Yeah I was never big on entering my own stuff, but I always liked seeing what everyone had, the rare models, and what's been modified. That was always fun. These days I have barely enough time to do what needs to be done at home.    Oddly enough, here in MA there are more car shows than ever in history! You'd think up here it would be dead, but it's bigger than EVER!          Took the 940 for its maiden voyage with the carburetor. At first I couldn't get out of the yard! This originally had the "Bosch" system (our other 940 has Regina - single fuel pump in fuel tank, and space-age-looking ignition coil on driver's fender) - that has dual fuel pumps. One in the tank, and one under the center left of the vehicle. I had unplugged the external one thinking I wouldn't need it with the carburetor ... but the way I have the pressure regulator hooked up, 90% of the fuel volume is going back to the fuel tank, so cranked all the way down, the regulator is only supplying a hair above 3.5 PSI to the carb. Turns out the in-tank pump (15 PSI alone, instead of 45) couldn't handle the load. Plugged it back in and went for a rip. Ran great!   Throttle response is always amazing with carburetors. ZERO delay that no FI system can reproduce. Also fires up in half the crank rotations as before. Low end power was DRAMATICALLY improved. There was an ongoing lean issue with the FI that I got tired of figuring out, so this is a MASSIVE improvement! Above 50 MPH on hills it feels SUPER weak, though. This is more than likely due to the timing not being advanced enough by the computer, since it believes there are multiple failures. I can live with that through the winter. Will keep me from passing slowpokes where I shouldn't and getting speeding tickets at least. 😁

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...