Jump to content

2014+ Lowering / Drop Kits

mjw930

By mjw930
in Modifications & Accessories

 Share

Recommended Posts

2005_Silverado New Member

2005_Silverado

Posted
Posted
1 minute ago, krzyd said:

I have a '14 Denali, I'm about ready to go from a 2" lift on 34" tires to a drop on Foose 22" rims and a supercharger. Looking for recommendations on the best drop kit/shock combo. Thanks in advance

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

  • Replies 3.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Heavy_Static
Heavy_Static

A few pics from last week:    

bakerrr
bakerrr

First post here Picked her about 2 weeks ago couldn't wait to start modifying it. Just installed Belltechs 4/7 drop this weekend It's low enough for the time being ??  

Nasty
Nasty

Posted Images

krzyd Enthusiast

krzyd

Posted
Posted
1 minute ago, 2005_Silverado said:

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.

 

FORGIVEN06 Enthusiast

FORGIVEN06

Posted
Posted
4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.
 


Aluminum a arms?


Sent from my iPhone using Tapatalk
  • 1 month later...
slee3247 Enthusiast

slee3247

Posted
Posted

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

  • Like 1
Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
12 hours ago, slee3247 said:

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, Stressin said:

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
8 minutes ago, slee3247 said:

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

I definitely want the extended range of travel for the diff, and I'm not too worried about resale...I haven't ever sold off any vehicle that I've owned, and don't intend on starting a new trend now either. If the time ever comes that I want to sell it and upgrade, then I fully expect to take whatever financial hit comes along with the modifications. Besides, I already have the feeling that I'm gonna want to go even lower at some point :)

 

I appreciate the heads up nonetheless!

  • Like 1
silvy2k17 Enthusiast

silvy2k17

Posted
Posted
On 12/19/2017 at 5:30 PM, Goinovr said:

4/6 Inez Hot Rods kit on 22x9.5 +25 305/45 tires.

truckwide.jpg

what wheels are those Goinovr? I like them a lot 

NoLand Enthusiast

NoLand

Posted
Posted
For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.
 
This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk

 

These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings

NoLand Enthusiast

NoLand

Posted
Posted
These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk

 

Can't honestly remember if there is a hole or not. If not, not a big deal to drill a 3/8" hole for a bolt. ?

blownZ71 Enthusiast

blownZ71

Posted
Posted
On 11/1/2017 at 9:42 PM, Derek66lsx said:

Couldn't resist any longer, it needed to be lower..

Im now at 2" front 5" rear drop, sits perfect, and the belltech shocks/struts ride 1000x better then the stock racho's 

just in time for winter, had to put the winter wheels on this weekend :(

gmc.JPG

I am in a similar position as you were. I have the rear leveled with the shackles but want to go lower. Is your front suspension steel or aluminum? As I have not really been able to find any solutions for an aluminum front A-arm setup on a 4x4. How did the alignment go on the front? Also, any rubbing of your 285's, or even close? My 305's barely rub at full lock so just wondering how bad that might get.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      That should answer the maximum depth difference between the stock and the PPE so its not hugely lower. As to the PML pan, they don't make any claims that it fits the L8T with the same transmission and in fact leave their information confusing, however on the surface it says "for Duramax" and so its hard to say. I know a while back and not sure which brand it was that specifically stated that the extra capacity pan that particular company made did NOT fit the gas version. 
    • fondupot
      Installed Bilstein 5100's on my 2024 2500HD - Worth it - VIDEO + GIVEAWAY Inside

      By fondupot · Posted

      There are several versions of the 5100's. Some for stock height, some for leveled, some for lifted.    Side note. I finally had a chance to tow with my 30' gooseneck with about 10,000 lbs of material on it this past week. Hands down the 5100's made the trailer towing much more stable and comfortable. I even had 10 cmu blocks in the bed. What a difference over the stock shocks. 
    • Tyler Gibbs
      Correct way to service 2024 l8t allison trans?

      By Tyler Gibbs · Posted

      According to PML, the stock pan is 4.3" deep - (PML info): Dimensions: at deepest area, PML pan is 7 inches, stock pan is 4.3 inches    PPE is 5.4" so roughly 1.1" deeper than stock
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I had not realized that PPE has come out with a version of a cast aluminum oil pan specific to being able to fit onto the 10L1000 with the L8T engine sometime this spring. I was doubting that anyone would come out with something beyond what Dorman had in more of a direct factory pan swap. I see from one comment that is on the PPE site that they found the pan to be tighter to install then the factory unit and having to flex the exhaust down to fit it. I didn't lookup any specs if they have any as per how much lower it hangs but as it holds more oil and has fins outside the pan it would no doubt hang a certain amount lower.    I looked back at the site and they do have some depth measurements to get a rough comparison to the factory pan total height or hang down if you will at the front and rear of the pan so that will give a good idea how much further down this pan would end up being for ground clearance issues.    2024-2026 GM 6.6L Gas 10L1000 Heavy-Duty Cast Transmission Pan – Pacific Performance Engineering    
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      I'm in constant amazement over the number of people that do oil maintenance by how they feel, what they were told, what materials cost, what brand A claims vs brand B.     Come to think of it, this behavior isn't exclusive to oil. 🤔 They drive this way too. 😬   There is a 20 plus page thread on BITOG on Mobil 1 Advanced Clean vs Valvoline Restore and Protect it would be amusing if it were not so........humanly pitiful.   Last Sunday we were are sitting at services and listening to a speaker talk about Jesus parable of the wide and narrow gates and he said something that hadn't dawned on me but totally fit the way people in general are about just about everything. He said there are so few people on the narrow path leading to a good reward not because the the narrow gate was hidden or hard to find but because the wide gate leading to a bad end it so darn easy and uncomplicated to follow!!!             

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...