Jump to content

Recommended Posts

Posted

Basically all the crap about corrosion protection the GM is applying is a total bite in the ass for them. I wonder if they have any feeling of complete failure. I mean if you you post it publicly you better prove it, well its a little late for that. So pathetic, isn't it. Appanently they don't know what extensive means! Oh and they state "enhances the trucks appearance" LOL so hard that is hurts. These trucks already look 8 plus years old underneath. What a joke.

  • Like 1
Posted

Does anyone actually believe this?

 

I'm sure some do, I was being sarcastic when I quoted GM's statement. I guess manufactures can claim anything nowadays without worrying about repercussions. I guess the frame rust and undercoat flaking off enhanced the trucks appearance. lol

  • Like 1
Posted

Basically all the crap about corrosion protection the GM is applying is a total bite in the ass for them. I wonder if they have any feeling of complete failure. I mean if you you post it publicly you better prove it, well its a little late for that. So pathetic, isn't it. Appanently they don't know what extensive means! Oh and they state "enhances the trucks appearance" LOL so hard that is hurts. These trucks already look 8 plus years old underneath. What a joke.

 

If you read their advertisement for the upgraded corrosion protection, it only applies to the body and says nothing about the frame. So technically, they're correct in their public posting. Sh!tty, but correct. Only a seasoned GM owner who knows about the wax coated frames would catch that they left this out of their advertisement so to the general public, they get away with it.

Posted (edited)

 

If you read their advertisement for the upgraded corrosion protection, it only applies to the body and says nothing about the frame. So technically, they're correct in their public posting. Sh!tty, but correct. Only a seasoned GM owner who knows about the wax coated frames would catch that they left this out of their advertisement so to the general public, they get away with it.

Is GM technically correct in advertising their trucks as being "like a rock"?

Edited by pm26
Posted (edited)

Is GM technically correct in advertising their trucks as being "like a rock"?

 

They haven't used that slogan since like '99 haha! I guess you could argue they've quietly backed away from their "like a rock" claim over the years.

Edited by Silverado-Hareek
Posted

As an original owner, I bought a '87 Thunderbird Turbo Coupe Demonstrator model and the undercarriage was sprayed with a Line-X type coating. After 28 years, the coating is still there.

  • Like 1
Posted (edited)

Silverados corrosion protection measures provide superior defense against elements in the environment, whether driving through farm fields, on construction gravel, or down a snow-covered highway, said Mark Yergin, engineering group manager, General Motors Corrosion Engineering and Labs. The new Silverado is our strongest truck yet, affording us the confidence that the truck will continue to meet customers needs throughout its life.

Additional 2014 improvements over previous models include:

All new body structures designed to minimize the potential for corrosion

Improved hem flange sealing on the doors and hood, and additional underbody flange sealing help keep the joints of the truck dry, discouraging deterioration that might occur from moisture

***Extensive and improved chassis corrosion protection that enhances the trucks appearance and lengthens the life of underbody components

Anti-chip protection on the lower body side for extra protection from stones or gravel.http://media.chevrolet.com/media/us/en/chevrolet/news.detail.html/content/Pages/news/us/en/2013/Sep/0905-silverado.html

Edit: the strange thing is, I haven't been able to find this same info about the 2014 Sierra. On GM's media site I could only find it on the Silverado.http://media.gm.com/media/us/en/gm/news.detail.html/content/Pages/news/us/en/2013/Sep/0905-silverado.html

If you read their advertisement for the upgraded corrosion protection, it only applies to the body and says nothing about the frame. So technically, they're correct in their public posting. Sh!tty, but correct. Only a seasoned GM owner who knows about the wax coated frames would catch that they left this out of their advertisement so to the general public, they get away with it.

Haven't we been thru this before, they specifically state "chassis" and guess what, the chassis consists of the frame.

"An example of a chassis is the underpart of a motor vehicle, consisting of the frame (on which the body is mounted)."

Edited by 14LTZZ71
Posted

Haven't we been thru this before, they specifically state "chassis" and guess what, the chassis consists of the frame.

"An example of a chassis is the underpart of a motor vehicle, consisting of the frame (on which the body is mounted)."

 

Have we? Haha sorry I don't remember reading that but I guess it does state it. I thought there was promotional video that showed them spraying the rock-guard and stuff and the frame was never addressed from what I remember. Anyway I don't know how it can be improved it's a worse wax coating than what they used to use.

Posted

Does anyone think this issue from the factory may have stopped after certain build dates?

Build dates 03/14 and up have an additional clear wax sprayed over the black stuff. Its a lot harder and I have 0 issues with rust on mine.
Posted

Build dates 03/14 and up have an additional clear wax sprayed over the black stuff. Its a lot harder and I have 0 issues with rust on mine.

Probably what was suppose to be done at the start of the 2014's but GM figured they would save a few bucks on the early builds.

Posted

My frame is horrible looking, The entire thing is orange colored with surface rust. I have not see any other new vehicle look this bad. Not even my 2005 tacoma that had to have the frame replaced due to rust. I plan on pressure washing it good this summer and getting under there and doing a good job at painting some sort of frame paint on it. I am not a fan of the thick gunky undercoating.

Posted

My truck was an August 2014 Build and I have found that the frame is rusting where there were welds or joints. The flat surface of the frame itself seems to be holding up alright. I know it's just cosmetic and the frames not going to rust through and break but it sure is annoying.

Posted

These frames are made of relatively thin walled C channels with some fully boxed in sections where the stresses are the greatest. Even though the frame is not likely to rust through for a number of years, it should be properly protected from corrosion, including the welds. It is not exactly made of two inch thick plate steel.

Posted (edited)

These frames are made of relatively thin walled C channels with some fully boxed in sections where the stresses are the greatest. Even though the frame is not likely to rust through for a number of years, it should be properly protected from corrosion, including the welds. It is not exactly made of two inch thick plate steel.

It's a fully boxed frame, not c channels. That's one of the reasons they dip it in wax to properly coat the interior surfaces of the boxed frame.

 

 

Sent from my iPhone using Tapatalk

Edited by Silverado-Hareek

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Sir, economics doesn't have a moral compass. 😉 Just say'n. 
    • One would think. BUT....This is what a Google search gives for the GM OLM system:    It doesn't measure oil condition save the highly indirect water temperature. It should measure oil temperature and as we've discussed they are not as closely related as one might assume. The algorithm is based on expected conditions at the end of a certain number of miles or revolutions. And sirs, this estimated value is not tilted in the engines favor. It favors the OEM's bottom line. There are no magical number of miles nor revolutions. No magical time limit. There is only what can be measured directly and only in the broadest of terms would the values used even come close to reality.    It samples nothing. It has no idea where the oil started or where it will finish given the limited values use to create the algorithm. It is just a reminder for the brain dead to do something at some time to keep the warranty in tact. Pure fiction.    Key Factors in Oil Life Calculation The OLM calculates the remaining oil life percentage based on the following factors: Factor Description Engine Revolutions Tracks the number of engine revolutions since the last reset, decreasing oil life with use. Mileage Since Last Reset Monitors the distance driven since the last oil change, capped at 7,500 miles for most models. Time Since Reset Decreases oil life over time, dropping to 0% after one year, regardless of mileage. Engine Temperature Adjusts oil life based on coolant temperature; exceeding 260°F sets oil life to 0%.  
    • Towing power and I guess MPG matter that’s why I may end up going with a gear swap as soon as they’re available for this truck if I’m correct
    • If I may, I'd like to post my prediction of the trim levels for the 2027 GMC Sierra, based on what was released/introduced today about the Chevy Silverado.   Using the "Professional Grade" wording already in use by GMC, here are the eight (8) trims I believe the Sierra will offer (comparable Chevy trim in parenthesis): Sierra Pro (Work Truck/WT) Elevation (Custom) Elevation Premium -or- Ultimate (Silverado) AT4 (Custom Trail Boss) AT4 Premium -or- Ultimate (Trail Boss) AT4X (ZR2) Denali (High Country) Denali Ultimate (N/A) If GMC would rather simplify the trim levels, then I predict six (6) with package upgrades in parenthesis: Sierra Pro (with a Graphite package upgrade option) Elevation (with a Premium -or- Ultimate package upgrade) AT4 (with a Premium -or- Ultimate package upgrade) AT4X (with AEV and Ultimate packages upgrade) Denali Denali Ultimate  Let's see if I'm close.
    • I have to believe there are already a bunch of threads on this, but my searches didn't turn up much. While I like the ease of a plugin solution like the Carbyte, It appears it disables the AFM or DFM too, and is not configurable to only disable the auto stop/start. So, I'm looking at the Autostop Eliminator product. I like the idea of it better, but I'm concerned about the install and having to pull so many panels to get it installed. Mines a 2026 work truck, so from what I've read it's a less involved install, but having watched a couple install vid's, I'm still a little intimidated. Might need to buy some plastic trim tools to get it done without breaking or marring stuff. Any experience intalling in a WT greatly appreciated.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...