Jump to content

Hood Latch Switch Bypass

TenshiWingusu

By TenshiWingusu
in Troubleshooting & Recalls

 Share

Recommended Posts

Linden16 Enthusiast

Linden16

Posted
Posted
33 minutes ago, TenshiWingusu said:

I hear ya. I would check the resistance on the new switch in both positions, you can force the latch closed with a screwdriver then pop it with the interior hood release. If the switch is in the spec mentioned above it's either bad wires somewhere or the control module has issues.

Yeah hey. I wonder if the dealership can silence the alarm that would be perfect as long as theres no ringing id be happy lol

  • 2 weeks later...
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

TenshiWingusu
TenshiWingusu

I made an account just to post the fix for this, couldn't find it anywhere.... Your mileage may vary but this is what worked for me.   After having my alarm go off continuously with the hood

Travis Dach
Travis Dach

Please Please Please,   Before anyone puts in a resistor to replace the hood switch, look at this first, especially if you are having these symptoms below.      Hood open warning w

Linden16
Linden16

But yeah i want my remote start thats handy lol. Buy a $60000 truck and have no remote start cause of a stupid hood sensor. Ill have to call the dealership and see. But i know theyll just charge you a

Posted Images

Linden16 Enthusiast

Linden16

Posted
Posted
On 2019-02-18 at 11:18 AM, TenshiWingusu said:

I hear ya. I would check the resistance on the new switch in both positions, you can force the latch closed with a screwdriver then pop it with the interior hood release. If the switch is in the spec mentioned above it's either bad wires somewhere or the control module has issues.

Do you think if I unplugged that sensor and got a aftermarket remote start would it work? Or would the aftermarket remote start still need to know that the hood is closed so would have to stay plugged in

  • 1 month later...
nissyota88 New Member

nissyota88

Posted
Posted

Can someone please show me a wiring diagram and pins on bcm. This truck got in a wreck and has a different wiring harness, but came stock with a hood switch with no pigtail

  • 5 months later...
jaytee10 New Member

jaytee10

Posted
Posted
On 4/20/2019 at 1:54 AM, nissyota88 said:

Can someone please show me a wiring diagram and pins on bcm. This truck got in a wreck and has a different wiring harness, but came stock with a hood switch with no pigtail

What model year truck do you have?

  • 2 months later...
Nick1220 New Member

Nick1220

Posted
Posted

I have a 2008 Chevy equinox that the factory remote start stopped working on. No service engine lights. No indication that a door or hood is open. I’ve changed the gas cap and even checked the tire pressure even though no lights indicated such problem. However I’m still having the same issue. The remote start won’t start the vehicle. The key fob locks/ unlocks the vehicle any and every time a button is pushed. Even illuminates the light when attempting to remote start but it’s like the process just stops. I’m lost definitely could use some ideas and can’t afford a garage to fix it. 

  • 1 month later...
ride_z71 New Member

ride_z71

Posted
Posted

One evening my 2018 stock alarm went off...I thought I must have hit the panick button on my remote...

The next morning I could not remote start the truck...

I get in, start it, and my hood open message was on with my check engine light...I checked the hood several times and it was opening and closing as it should...

Searched and found this post, measured the resistance between the black and red wire on the hood sensor connector and it read 529 ohms ope or closed.

Replaced the hood sensor and it fixed the open hood message and then I had to clear the code...

 

Tempatures were in the 20's to 30's and I had 51,000 miles...Makes no sense.

ScottC19 New Member

ScottC19

Posted
Posted

Hey Everyone, just had this problem on my 2018 Silverado LT. I think i found the issue. If you go to the hood with it closed and push down lightly on the hood even with your finger it will have some play. Open the hood, there are 4 rubber "standoffs" i'll call them. They keep the hood a certain distance from the plastic cover on the inside. turn them to the right they go down, turn left they stick out further. I just loosened mine so the hood would stand off the truck a bit further this makes the hood engage the latch more to hold it down. I think that movement of the hood was making the sensor think the hood was open because there was no pressure against the latch from the hood. 

  • Like 1
ScottC19 New Member

ScottC19

Posted
Posted
On 2/17/2019 at 1:57 PM, Linden16 said:

Yeah its the whole late assembly correct. So i installed that and still have the same problem yup.. not sure what else could be causing it. And like i said it only rings when the trucks cold. After a few minutes of driving it stops

Hey Everyone, just had this problem on my 2018 Silverado LT. I think i found the issue. If you go to the hood with it closed and push down lightly on the hood even with your finger it will have some play. Open the hood, there are 4 rubber "standoffs" i'll call them. They keep the hood a certain distance from the plastic cover on the inside. turn them to the right they go down, turn left they stick out further. I just loosened mine so the hood would stand off the truck a bit further this makes the hood engage the latch more to hold it down. I think that movement of the hood was making the sensor think the hood was open because there was no pressure against the latch from the hood. 

Jason56 New Member

Jason56

Posted
Posted (edited)

Hey y’all just wanted to post that I tried the resistor and it worked!  I bought 2.2k ohm resistors off Amazon and soldered it in.  I was getting +\- 520 ohms with the hood open or closed so I knew it was the sensor.  Thanks for posting!

Edited by Jason56
  • Like 1
jagabom (Esquire) Enthusiast

jagabom (Esquire)

Posted
Posted
20 hours ago, Jason56 said:

Hey y’all just wanted to post that I tried the resistor and it worked!  I bought 2.2k ohm resistors off Amazon and soldered it in.  I was getting +\- 520 ohms with the hood open or closed so I knew it was the sensor.  Thanks for posting!

Can you post a link to the resister?

Thanks

Jim

gmgmgmgmgm New Member

gmgmgmgmgm

Posted
Posted

The resistance values (ohm's) stated earlier in the thread are correct, ~740 and ~2.2k ohms for opened and closed respectively. The linked 2.2k ohm resistors should work fine bypassing the switch.

 

For anyone having the issue, GM has a TSB out for this specific issue as well, regarding loose/bad grounds. If the resistance values of your hood switch are within spec. You may have a bad ground.

 

In my case it turned out to be caused by the ground braid (labled 3). Under the hood on the drivers side firewall. It is a thick braided flat steel cable bolted to the body cowl, bolt was lose an jiggled around. Throwing hood sensor codes (short to battery & open circuit). You may need to check the opposite end of the ground braid as well on the left rear cylinder head.

 

https://imgur.com/a/kddguGK

 

spacer.png

 

spacer.png

 

spacer.png

 

  • Thanks 1
  • 1 month later...
KCAudio New Member

KCAudio

Posted
Posted

I have a 2014 Sierra Denali 1500. The hood open alarm comes on when I have to much going on inside the truck, for instance if I have my AC full blast and AC seats (passenger/driver) going all at the same time the alarm will start to chime. I unplugged it before and it stopped. I was able to continue as normal. I am not to sure if it’s just the hood sensor or if the problem may go deeper, like to the BCM. Can anyone let me know if changing the sensor out would be the fix?

 

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By asilverblazer · Posted

      Compression test? Weird noises? Fuel trims?
    • asilverblazer
      Wow I'm in a pickle. (Broke down truck) and a story.

      By asilverblazer · Posted

      I suspect at some point in the near future, the hardware will be free and you pay a subscription to access the vehicle - alldata style.
    • parthery
      BAK MX4 EZ-Lift Install and Review

      By parthery · Posted

      I've been eyeing an upgrade to my tonneau cover for a bit now.  Intrigued by the BAK MX4 EZ-Lift with the torsion spring and went for the upgrade.  Thoughts and musings during unpacking, install and a few days of usage.   Once my order went into Realtruck, it took about 4 days to ship.  Unfortunately, FedEx Ground destroyed the box and contents and it was unusable upon receipt.  To Realtruck's credit, one email with pictures and an RMA was sent to me to send the first one back, and another unit was shipped out.  It arrived 3 days later, unscathed.   I opened the box and it looked like every other BAK MX4.   Biggest differences are the rails and retaining clamps, and of course the spring attached to the cover itself.     NOTE - if you are upgrading from a MX4 to the EZ-Lift, you will have to replace the rails.  The EZ-Lift rails have a notch cut in them to allow the new style retaining clamps to fit properly.  The new retaining clamps also have 2 knobs/carriage bolts and there are two tracks underneath the front panel. The strap clips are mildly different (more like the Undercover Flex clamps) in that the screws go in from the underside.  Personally I prefer these over the BAK clamps that use the nutserts that are a nuisance to install.  The remainder of the parts in the box (drain tubes, rail clamps, and bumper pads) are standard issue BAK.     I did not replace my front bed seal at the time because it seemed to be in decent shape.   BAK recommends shims on the GM trucks unless you place the clamps on the flanges about 1/3 of the way in from both the front and rear of the bed.  I shimmed the front and the middle, and initially placed the clamps equidistant.  This also turned out to be a mistake, because when I set the cover in place, the new style retaining clamps wouldn't clear the front clamp.   New style clamp inserted in the track:     And the issue which occurred because the front rail clamp was too far forward:     Once I removed the shim from the front of the bed, and slid the clamp back to the front flange, everything cleared fine.     The cover set on the rails without issue and I installed the strap clamps.  After I completed my adjustments, I pulled the pin to activate the torsion spring.  Mistake #3 on my part.  PULL THE PIN AS THE VERY VERY VERY LAST STEP!  The reason is, once you pull the pin, the torsion spring is activated.  If you have to loosen the front clamps and adjust the cover, the front panel will - by virtue of the spring, refuse to lay down.  The only way to get it to lay down so you can reinstall and tighten the clamps is to fully open the panel against the back of the cab, which will then allow the front panel of the cover to lay down and be tightened.  Not a big deal unless you haven't installed the foam pads yet (typically the last step) because minus the foam pads, you will need to place something between the frame of the cover and the back window so it doesn't get scratched.  The next time I install one I will install the foam pads before I pull the pin and activate the spring.   After using it for a few days:   The spring assist is great.  You literally can open it with one hand.  My shoulders aren't getting any younger and this was part of my motivation to swap out. The second panel latches and unlatches itself as you open and close the cover.  Neat in concept, however it took me a minute to get used to closing the cover and not hearing the "latching" sound that would tell me it was locked in place. The paddle handles are a huge upgrade and I wouldn't be surprised to see them become the standard across the Realtruck line.  They effectively eliminate the concern that a thief could coat hanger the cover open and get to the contents in the bed. I'm not sure why the very front panel on my cover has a different finish from the other 3 panels.  I have a request into Realtruck to find out if mine was not manufactured properly or if it was by design.   All in all I'm pleased.  Same level of protection, looks good, keeps stuff mostly dry (they all leak around the tailgate) and easy to install.
    • KARNUT
      PF63 Oil Filters Going Away?

      By KARNUT · Posted

      Thanks not an answer 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      /facepalm

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...