Jump to content

Ambient Air Temperature Reading is Wrong!

Jack Christensen
 Share

Recommended Posts

Jack Christensen Enthusiast

Jack Christensen

Posted
Posted

2019 Silverado Trail Boss LT Z71: 9,500 miles

 

My ambient air temperature reading on the infotainment system has always been about 7 - 10 degrees higher than what the actual temperature is.  I have taken it into the dealer 2 times. The first time, they "Said" they tested it and it looked normal.  I doubt they tested anything as it was just one of the items on a list of about 5 other things they were doing with my truck.  I took a pic of the temp on my phone/watch next to the infotainment temp and it showed an 8 degree difference.  They said to keep an eye out for updates to the system.. Ugh.  I took it in again about 2 weeks ago and a different dealer replaced the sensor.  Apparently it is in the passenger side mirror?  Anyway, that did not fix the issue.  It is still not accurate!

 

I read another post on a different site and it said to try an instant update by: 

To perform an instant update of the Ambient Temperature Sensor, simultaneously press and hold the Re-circulation button and A/C button on the HVAC control head.

 

I am going to try this over lunch - i'll update my post soon.  Anyone else have this issue?

Photo Sep 23, 7 36 04 AM.jpg

newdude Senior Enthusiast

newdude

Posted
Posted

They never are accurate.  Its in the pass. mirror.  The information to the temperature display is also "filtered" so there is some buffer or delay to its reading.  I wouldn't sweat an ounce more about it unless it starts reading -40F or 198F.  Then you know its a bad sensor. 

 

Quote

 

Outside Air Temperature

The Ambient Air Temperature Sensor is located in the Passenger Outside Rearview Mirror and varies it’s resistance with temperature. The Engine Control Module (ECM) reads the resistance value to determine temperature. The time of and rate of the temperature update is based on an algorithm in the Engine Control Module (ECM) software. Factors such as, last reading, current reading, length of time vehicle is been off/on, power mode, vehicle speed, driven distance, and sensor location are all considered by the Engine Control Module (ECM) to know when to update the displayed temperature on the Info Display Module. For example, if the sensor is located near the engine compartment, and the vehicle has been turned off for only 10 minutes then restarted, the ECM will wait until the vehicle is driven to get more accurate air flow across the sensor before it updates the display.

 

 

 

 

  • Like 1
amxguy1970 Senior Enthusiast

amxguy1970

Posted
Posted

It won't be very accurate, where readings from a phone come from either a official source and reading location locally (either through a local news center or national weather center readings) a vehicle uses a sensor at that point and can have so many things impact it. Heat from the black asphalt, shade, wind speed from driving, precipitation, etc. Use it as a ball park, and if you really want to test it take a thermometer and place it right by the sensor, that is more accurate what your truck is reading versus your phone at that point as apps vary depending on which is being used. Shoot, I just pulled up two different news sites locally, one shows 48 degrees and the other 53 degrees. Don't put much in to it.

 

Tyler

Jack Christensen Enthusiast

Jack Christensen

Posted
  • Author
Posted

Thanks for the feedback!  My 2004 Silverado was always accurate.  I guess I am too much of a perfectionist.  I expect things on a new truck to be accurate or work in general ; )  No biggie, more of an annoyance than anything else!  

econometrics Senior Enthusiast

econometrics

Posted
Posted

My 2007 Silverado temp readout was much more accurate than my 2019, too. 

 

I find that once you get going down the road, the truck reading gets closer to the weather station readings. It probably has to do with the airflow around the sensor. When it's just sitting there under the passenger mirror in the sun, it's likely perceiving the temp of the mirror dome. 

  • 1 year later...
Rare100thHD New Member

Rare100thHD

Posted
Posted

I just cut an air flow hole in the bottom of my mirror......therefore it cools down the heat built up inside the mirror sitting in the hot sun......corrects temp much faster now....

kelly mccue New Member

kelly mccue

Posted
Posted

I have a 2020 2500HD Chev truck with ambient air temp. off by 12-14 degrees. Its been in the chev shop 4 times. Seems to get worse every time that I bring it in. The temp. pod was replaced twice. The temperature reading is close when I start up the but as I drive the truck it gets worse, showing warmer , never consistent.

kelly mccue New Member

kelly mccue

Posted
Posted

I have a 2020 2500HD Chev truck with ambient air temp. off by 12-14 degrees. Its been in the chev shop 4 times. Seems to get worse every time that I bring it in. The temp. pod was replaced twice. The temperature reading is close when I start up the but as I drive the truck it gets worse, showing warmer , never consistent.

  • 10 months later...
Andret77 New Member

Andret77

Posted
Posted

Quick question. The temp has read -40 a few times today and then has really been all over the place. I know this is a symptom of a faulty ambient air temp sensor. However, my pass mirror adjustment is not working either. Do you think there could be a power issue? I have the new temp sensor coming in today. My AC has been intermittent for two months. truck was bought in September but the service times are so long I won't wait a week. 

redwngr Senior Enthusiast

redwngr

Posted
Posted
3 hours ago, Andret77 said:

Quick question. The temp has read -40 a few times today and then has really been all over the place. I know this is a symptom of a faulty ambient air temp sensor. However, my pass mirror adjustment is not working either. Do you think there could be a power issue? I have the new temp sensor coming in today. My AC has been intermittent for two months. truck was bought in September but the service times are so long I won't wait a week. 

What truck and engine?

Transient Senior Enthusiast

Transient

Posted
Posted

Remember, it's a thermistor, not a thermometer.  Car companies use them because they are cheaper.  The downside is they aren't as accurate.  I've been buying new GM vehicles for 16 years now.  All have/had the ambient temp readouts.  All are grossly wrong when I first driving the vehicle.  All get/got within +/-3°F after driving for about 2 minutes.  It's accurate enough.  That's what matters.

K455 Enthusiast

K455

Posted
Posted

My 19 Custom TB reads about 7degrees high since new,not worth it to me, to bring it in and have the dealer touch it and be worse or something else

  • 1 year later...
Robert Donohue New Member

Robert Donohue

Posted
Posted

I have a 2019 Chevy 3500 Duramax that always shows the engine light on when the ambient temp goes wacky. I have had it changed twice in three months by the dealer but the light comes back on within a few days. Can you tell me if there is another fix to try? I appreciate any further insight you can provide.

32BEAB42-1F4C-4B0A-BA10-B33767EFF032.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      New or used

      By KARNUT · Posted

      WOW, something we agreed on. I only bought at sticker twice. A 94 impala ss and an Acura intagra type r. Made money on the first. Still have the second.
    • Atlas
      New or used

      By Atlas · Posted

      I prefer new, but not without a deal. Historically I've bought severely aged new inventory, leftover model year, unpopular configuration kind of stuff that sits around on dealer lots until they just want it gone. $10k off MSRP kind of stuff on a mid-priced truck. That really, really helps knock down that first year depreciation. It also requires being somewhat flexible on colors and options. I wouldn't buy a 4 cylinder if I was looking for an 8 cylinder, but if I got blue paint instead of black, or a great deal was lacking a minor option, I'm willing to overlook those things for savings.   Used <> used. Condition and history are everything. If I'm buying used I'm looking for cream of the crop. The truck from the guy who religiously pampers it, and then decides a year later he wants newer and nicer. NOT the ex-rental vehicle, or the crew cab traded in by the family with 7 kids who like to throw food, and the oil only got changed when there was time long after the oil life monitor started alerting.
    • Atlas
      OCI, not when but why?

      By Atlas · Posted

      @Grumpy Bear the conclusion from your post about doubling engine life has me curious. Are we literally talking an expected life of 250,000 miles potentially becomes 500,000 miles with a step up in filtration for fresh oil at "the oil factory" when it's bottled? I know you said that's a single variable among many, but, that's significant if the implication extends that far into a real world use case. I would think the oil marketing folks would really eat that up and make it known.   Particles introduced during oil change is a fairly easy one to avoid, but probably not intuitive as one would think. I.e. using a clean funnel. But...what was it wiped with? Paper towel leaves behind little fibers. A solvent if not dried is not something one would want to introduce into their engine with clean oil. And, keeping the oil filler neck clean and free of buildup.. Look at some guys engine bays and they're an absolute mess. Some say that's better than the drawbacks of cleaning it. I'm not a buyer of that idea.   I've also wondered if "flooding" the top end of the engine with oil while filling is a bad idea. During normal lubrication the oil flows in a gutter back into the galleys. But if you flood the area you're potentially washing the top of the rockers, springs, and other areas which may not get much oil wash normally, and you're mixing all that into the new oil. I just don't have the patience to pour slowly. 😆    
    • Newduramaxh*ar
      DTC P2C48 auxiliary cooling pump

      By Newduramaxh*ar · Posted

      It was a bad pump, i had a dealer next day the pump. Gm part #86591535. Tools needed 10mm socket, pliers for hose clamps, 1/2gal of Dexcool. About 30mins to remove and install, pump located near oil filter on driver's side frame rail. I had a local mobile mechanic delete the code, he had a snap on scan tool. My scanner could not delete the code. I drove back home about 700 miles since then, and no check engine light. Hope this helps someone in the future in the same situation i was in. Thank you to all that helped me.
    • MORSNO
      Road Master Active Suspension

      By MORSNO · Posted

      Good to hear!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...