Jump to content

2014+ Lowering / Drop Kits

mjw930

By mjw930
in Modifications & Accessories

 Share

Recommended Posts

2005_Silverado New Member

2005_Silverado

Posted
Posted
1 minute ago, krzyd said:

I have a '14 Denali, I'm about ready to go from a 2" lift on 34" tires to a drop on Foose 22" rims and a supercharger. Looking for recommendations on the best drop kit/shock combo. Thanks in advance

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

  • Replies 3.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Heavy_Static
Heavy_Static

A few pics from last week:    

bakerrr
bakerrr

First post here Picked her about 2 weeks ago couldn't wait to start modifying it. Just installed Belltechs 4/7 drop this weekend It's low enough for the time being ??  

Nasty
Nasty

Posted Images

krzyd Enthusiast

krzyd

Posted
Posted
1 minute ago, 2005_Silverado said:

depends if you have autoride or not (Assuming SUV) or if its a truck, then it depends how low you want/plan to eventually go.

4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.

 

FORGIVEN06 Enthusiast

FORGIVEN06

Posted
Posted
4wd truck, I don't think it has autoride, I'm thinking 3/5 drop.
 


Aluminum a arms?


Sent from my iPhone using Tapatalk
  • 1 month later...
slee3247 Enthusiast

slee3247

Posted
Posted

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

  • Like 1
Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
12 hours ago, slee3247 said:

For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.

 

This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, Stressin said:

Thanks Shaun. I remembered your post about Timbren stops earlier last year while I was looking around at the various options this past week. Just bought an '18 DCSB last week, and it's going in for a 5/7 next weekend. We're notching it and I'm going to keep the Belltech stops on it for now, but wanted to have a better option available if needed. This was it!

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

Heavy_Static Enthusiast

Heavy_Static

Posted
Posted
8 minutes ago, slee3247 said:

These will fit without a notch if you don't want to install one! One less major modification means (hopefully) better resale if you decide to sell the truck off in a few years. Always planning ahead :thumbs:

I definitely want the extended range of travel for the diff, and I'm not too worried about resale...I haven't ever sold off any vehicle that I've owned, and don't intend on starting a new trend now either. If the time ever comes that I want to sell it and upgrade, then I fully expect to take whatever financial hit comes along with the modifications. Besides, I already have the feeling that I'm gonna want to go even lower at some point :)

 

I appreciate the heads up nonetheless!

  • Like 1
silvy2k17 Enthusiast

silvy2k17

Posted
Posted
On 12/19/2017 at 5:30 PM, Goinovr said:

4/6 Inez Hot Rods kit on 22x9.5 +25 305/45 tires.

truckwide.jpg

what wheels are those Goinovr? I like them a lot 

NoLand Enthusiast

NoLand

Posted
Posted
For those of you with a 7" rear drop looking for a good alternative to bump stops, look at Timbren products. I chose their "Rubber Spring" A140-65. It is a 1.885" tall rubber bump stop that has a nominal weight capacity rating of 500 lbs, and has a bump load capacity of 900 pounds. Their maximum deflected height is 1.1875", which means your differential and brake line/hose brackets will never hit the bottom of the bed. I purchased the set for ~75 USD. Just remove your factory bump stop brackets with a plasma cutter or sawzall, drop a 3/8" bolt through the existing hole, and put a nut on the underside. With the vehicle on flat ground at ride height, there is 5/16" clearance between my bump stop and the landing on the axle tube.
 
This is a relatively simple solution that provides a good combination of load capacity (can still use a half ton truck like a half ton), and ride comfort. I have zero qualms throwing two supermotos in the back of the truck, or hauling a thousand pound load. If you have any questions feel free to shoot a DM. Just something I found and figured I'd share.


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Are these bolted to the frame or the axle pad? I bought some low profile bump stops from Mcghaughys but I like the design of these better.


Sent from my iPhone using Tapatalk

 

These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings

NoLand Enthusiast

NoLand

Posted
Posted
These are bolted to the frame. I tried the mcg bumpstops but they blew out within a week. Give these a shot! They're cheap enough. I believe I found them for sale on sdtrucksprings


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk
slee3247 Enthusiast

slee3247

Posted
Posted
2 minutes ago, NoLand said:

 


Cool, I’ll have to take a look. I was under my truck this weekend installing helper bags and didn’t even realize there was a hole in the frame right there. I’ve been running without bump stops for awhile, but I know I need to get some on there. I’m only lowered 5 in the back, so it hasn’t been causing problems but we’re getting ready to get a camper trailer.


Sent from my iPhone using Tapatalk

 

Can't honestly remember if there is a hole or not. If not, not a big deal to drill a 3/8" hole for a bolt. ?

blownZ71 Enthusiast

blownZ71

Posted
Posted
On 11/1/2017 at 9:42 PM, Derek66lsx said:

Couldn't resist any longer, it needed to be lower..

Im now at 2" front 5" rear drop, sits perfect, and the belltech shocks/struts ride 1000x better then the stock racho's 

just in time for winter, had to put the winter wheels on this weekend :(

gmc.JPG

I am in a similar position as you were. I have the rear leveled with the shackles but want to go lower. Is your front suspension steel or aluminum? As I have not really been able to find any solutions for an aluminum front A-arm setup on a 4x4. How did the alignment go on the front? Also, any rubbing of your 285's, or even close? My 305's barely rub at full lock so just wondering how bad that might get.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,897
    Total Members
    8,960
    Most Online
    ncleg
    Newest Member
    ncleg
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,477 Guests (See full list)

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...