Jump to content

Safety Chain Hookup

Mike Hamm

By Mike Hamm
in Towing, Hauling & Hitches

 Share

Recommended Posts

FreeAmerican Enthusiast

FreeAmerican

Posted
Posted

FYI, those hooks are too small as well...my RV came with those, and I had to swap out with regular chain hooks because they wouldn't fit the receiver holes.

 

I think those s-hook are meant to pass through the holes in the receiver and then hook back onto the chain, but mine didn't have enough chain to do that either.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

I don't think they are meant to pass through, mine won't. I have to hook the big end of the S through the hole in the hitch.

  • Replies 39
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Chevor
Chevor

Time to stop at a scale and see what the Commercial inspector says....   Me being commercial could see myself getting two tickets with that set up...   #1 Are quick links rated for trailer? #2 Br

sdeeter19555
sdeeter19555

Those quick links aren't rated strong enough for my liking, the only way I would do that loop of chain would be to use a true clevis.   I did what the others stated, changed the hooks out for ones

sdeeter19555
sdeeter19555

Not to mention if the receiver separates from tow vehicle, you probably have worse things to worry about at that point in time...   I've only heard of it twice, once was a uhaul-installed hitch with

Posted Images

sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

On the 2.5" receiver, mine would pass but not enough to loop back and leave slack for turning.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

Mike Hamm Enthusiast

Mike Hamm

Posted
  • Author
Posted

I did what the others stated, changed the hooks out for ones that fit right...

 

Can you provide a link to the hooks you ended up getting? Based on what you have said about other suggestions, your hooks must meet all your criteria so I'd be interested in checking out the same ones you got.

Thanks.

sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

Can you provide a link to the hooks you ended up getting? Based on what you have said about other suggestions, your hooks must meet all your criteria so I'd be interested in checking out the same ones you got.

Thanks.

I replaced the factory s-hook with a grade 70 chain hook with safety catch that fit my receiver.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

  • Like 1
sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

This is my utility trailer, not my camper; but it will give you the idea...and the 2.5" receiver on my truck, which those hooks fit perfectly.

 

I've installed chain hooks on every trailer I own because they are easier to use and work better.16d39cecc36758b6ba48c6a6205eae48.jpgad38b4483d51ada525f700cc1111bd8b.jpg

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

Mike Hamm Enthusiast

Mike Hamm

Posted
  • Author
Posted

Thanks for the pics and hook info. I can see why your setup works easily. The holes in your hitch are way bigger than on mine. That's been the trick. Finding something small enough, yet strong enough, to fit.

Chevor Senior Enthusiast

Chevor

Posted
Posted

Here is a 13. Up and out. Not sure if new hitch is any different.

20170429_081619-1_zpsi6foxicu.jpg

Mike Hamm Enthusiast

Mike Hamm

Posted
  • Author
Posted

Here is a 13. Up and out. Not sure if new hitch is any different.

Yup, very different. The "up" holes (in your pic) in the 16 are about the diameter of a pencil. The holes on either side of the receiver are also smaller.

Believe me, if it had been as simple as your pic makes it look, I wouldn't be asking for ideas.

SouthpawHD Enthusiast

SouthpawHD

Posted
Posted

I used two 5/8" quick links from Tulsa Chain, rated for 8,100 pounds each. I then attached an eye bolt through the bottom of the hitch to hook up the safety brake cable (this idea was from forum member jhplak325).

post-140744-0-62030000-1493650747_thumb.jpg

post-140744-0-62030000-1493650747_thumb.jpg

post-140744-0-62030000-1493650747_thumb.jpg

post-140744-0-62030000-1493650747_thumb.jpg

  • Like 1
Mike Hamm Enthusiast

Mike Hamm

Posted
  • Author
Posted (edited)

I used two 5/8" quick links from Tulsa Chain, rated for 8,100 pounds each. I then attached an eye bolt through the bottom of the hitch to hook up the safety brake cable (this idea was from forum member jhplak325).

Yeah, it looks like I'll be going with the 5/8" links too. The eyebolt is an interesting idea for the brake cable. Does the safety cable just slide through the slight open end of the eyebolt?

Edited by Mike Hamm
SouthpawHD Enthusiast

SouthpawHD

Posted
Posted

Yeah, it looks like I'll be going with the 5/8" links too. The eyebolt is an interesting idea for the brake cable. Does the safety cable just slide through the slight open end of the eyebolt?

My safety brake cable has a snap link on it, so I just attach it to the eyebolt.

 

Ideally I think the safety cable should be attached to frame somewhere, by I couldn't locate a good spot.

sk Senior Enthusiast

sk

Posted
Posted

My safety brake cable has a snap link on it, so I just attach it to the eyebolt.

 

Ideally I think the safety cable should be attached to frame somewhere, by I couldn't locate a good spot.

 

This. You actually shouldn't attach your breakaway cable to the same spot as your safety chains. I have seen receiver hitches come off the truck frame completely. When that happens if your breakaway cable is attached to the hitch then the cable will never pull and your emergency brakes will not activate. The trailer will actually just float away with the hitch and receiver still attached to the ball.

SouthpawHD Enthusiast

SouthpawHD

Posted
Posted (edited)

This. You actually shouldn't attach your breakaway cable to the same spot as your safety chains. I have seen receiver hitches come off the truck frame completely. When that happens if your breakaway cable is attached to the hitch then the cable will never pull and your emergency brakes will not activate. The trailer will actually just float away with the hitch and receiver still attached to the ball.

Right. But until GM actually thinks through that these trucks do some towing, there aren't too many options.

 

Now that being said, these hitches are part of the frame and the chances of them falling off are rather slim. And even if they did, the safety brake cable only needs a little tension to be set off. And the slightest dragging on the road might just be enough in most cases.

Edited by SouthpawHD
sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

Not to mention if the receiver separates from tow vehicle, you probably have worse things to worry about at that point in time...

 

I've only heard of it twice, once was a uhaul-installed hitch with brass bolts (to prevent corrosion of course), and the other was a 2nd gen Dodge that had a metal fatigue failure from being overloaded all its life (rip parts of the frame off too). In all my years following the diesel forums, those are the only two hitch-related failures I can remember.

 

I worry more about someone tampering with my setup...stopped at a rest area, some teenage kids were hanging behind a SUV when I pulled in. I ALWAYS do a walk around before I start back down the road...the jerks had pulled the spring clip from the hitch pin so that it would fall out later down the road.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

  • Like 2
Mike Hamm Enthusiast

Mike Hamm

Posted
  • Author
Posted

Got my new quick links installed. I think I'm going to like this better than the other setup.

Trailer is at the dealer for some warranty work so I'll be giving these a try when going to pick it up.

post-156314-0-50789200-1494279258_thumb.jpg

post-156314-0-50789200-1494279258_thumb.jpg

post-156314-0-50789200-1494279258_thumb.jpg

post-156314-0-50789200-1494279258_thumb.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Black02Silverado
      New Retail Account Promo

      By Black02Silverado · Posted

      For a limited time, retail accounts receive a free fender cover (G2803) with their order of $750 or more when they use code FENDER926 at checkout. The promotion runs through Sept. 8, 2026. Own a business and want to apply for a retail account?  Apply here. https://www.amsoil.com/business-opportunities/sell-in-your-store/?zo=521390  
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      Thanks for that, yes just because I could I measured what came out just to give me some guidance although I already knew to expect it to take at least 9.5 to just throwing in the whole 10 quarts off the shot and doing a one and done heat cycle to drop out the excess to get to the proper level. I don't recall exactly now what I measured that came out but was less than I put back in, I knew I spilled some on the garage floor but the main part was that I was thrilled in the discovery I did not have to touch my exhaust to flex it down. The gasket manipulating is a pain of course to create that clearance to take the pan out and put back in but its all very doable if one is careful and not forcing the gasket to flex too much. From the quote I got at a transmission shop of 900.00 here in Canada ( never asked at the dealer what they charge ) I saved 700.00 doing it myself after paying for the supplies so that to me paid very good wages !, and I knew what fluid was put in and that I had changed the filter and that the level is correct without any doubts. 
    • bojanglespa
      2016 Sierra 1500 6.2L lifter Failure 🤨

      By bojanglespa · Posted

      I do have one of the AFM diasable box, using it for last 1.5 years.
    • Mellowth
      Tonneau cover and rack combo

      By Mellowth · Posted

      I found a setup that lets me open the cover partway with racks installed, using side-rail-mounted systems for easy access.
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Typically its said and I agree so far that the engine oil drain plug oring is not required to be changed out unless you see some damage happening to the oring as apparently the oring lasts well. The dealer I have been getting a few parts from never even stocked the oring but instead stocked the whole drain plug that comes with a new oring which for the dealer is easier because they just throw in a new drain plug if there was any question about damage on it as well and charge the customer accordingly but again only if it is needed.    Also a hint about the drain plug oring to help it last vs a risk of causing damage to it, after its been removed and wiped off or washed off ( that is a whole other topic about some solvents damaging orings because some solvent types do ) to make sure to relube the oring with a bit of new oil so that it won't "grip" on the sealing surface of the pan and needlessly stress out the oring. Its no different than putting some oil on the sealing ring of the engine oil filter. So I just grabbed a new drain plug to have on hand although more recently bought just the oring as well but as its special it costs half the price of the drain plug ... !   Since you mentioned the hate to be empty handed theme, I am not sure what you have in the way of filter removal tools as I like using the exact sized for the filter steel 1" wide band with side to side swivel handle filter removal tool, and it can be used to snug up the filter without risk of damaging a filter as well ( its probably a lisle brand I have ). The drain plug hex size is 15mm and I always like using a 6 point socket if I have a choice and with this truck I've been using just a 3/8 ratchet that has a fairly long handle. Do you have a funnel that will work to pour oil in as that is definitely the short coming bastard part about the design with that fill port on the valve cover on such an angle that no normal funnel will even work. There are adapters and things on the market that will set into or screw into that fill port, I didn't want to deal with US shipping as that is all I was seeing at the time so caved and bought a Lisle brand multi vehicle fit adapter funnel kit and it really works well but there are much less expensive adapters out there that work in conjunction with an off the shelf funnel that would do the job also. Now that I have it, I like how it works and works so slick with the shape of the Amsoil 1 quart containers I have now switched over to. Whatever you do, have a funnel system of some sort as you will be swearing if you dropped the oil and then realize you have nothing to properly pour new oil in without spilling it all over the engine !.     Other comments, quite a bit of oil flows out down the filter when its cracked loose due to the housing above the filter so let it dribble down the filter until it slacks off flow and then remove the filter to create less possible mess. It seems these engines can sit for quite a while and drip and if you have time let it sit there and drip out of the engine as much as it wants. Also a good time to grease the 9 zerks on the front end, that's my typical practice anyway to grease the suspension and steering each time I change the oil. And remember to reset the oil change minder ( not something I am used to doing with older vehicles and equipment ). 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...