Jump to content

Recommended Posts

Posted
Just got back from a New Orleans -> Houston drive and tried to do a little MPG calculating/estimating. 
 
From DIC for as long as I could sustain. Please note this is not scientific, just gives a rough idea in real world driving. 

Cruise Control set to:
60mph - 32/33mpg
65mph - 29/30mpg
70mph - 25/26mpg
75mph - 22/23mpg
80mph - 20mpg
 

Crew cab 3.0L 4wd Z71 275/60R20 stock Dueler ATs

Temp: low 70’s, not very windy, “low” humidity considering the territory [emoji38]

 
I plan on trying to fine tune this as accurate as possible to compare once I get leveled and bigger tires : )
I see very similar numbers with mine at speeds above 75 but seem to get around 25-26 at 65-70. I do have larger and much heavier duratracs on mine though. Thinking of switching back to a lighter tire for summer driving. Even with the heavier tires but with this warmer weather still seeing about 22 mpg in town, granted it's small town driving

Sent from my Pixel 2 using Tapatalk

  • Like 1
Posted
2 hours ago, HondaHawkGT said:

The best way to destroy a modern diesel is to start it up, drive a few miles, and shut it back down. I watched a guy with a Ram 1500 Ecodiesel destroy two engines plus exhaust system doing that. He's drive across town to work every day. If you have a habit of doing short drives like that, diesels with modern emissions systems are not for you.

I agree and understand this but I think 20 miles is plenty fine. This is why my LML has such low miles. I bought it to tow the boat and I only drive it if I know it will get up to operating temp. 

 

I have a LM2 on order and will be using it for a service vehicle. Some days I drive a mile or two to a customer then have multiple ones blocks apart from there...other days I drive 20+ miles before I get to the first one. I'm hoping that the cooling system gets things to temp faster as they describe it to do. If not, it's under warranty.

  • Like 1
Posted
1 hour ago, Whipped500 said:

I agree and understand this but I think 20 miles is plenty fine. This is why my LML has such low miles. I bought it to tow the boat and I only drive it if I know it will get up to operating temp. 

 

I have a LM2 on order and will be using it for a service vehicle. Some days I drive a mile or two to a customer then have multiple ones blocks apart from there...other days I drive 20+ miles before I get to the first one. I'm hoping that the cooling system gets things to temp faster as they describe it to do. If not, it's under warranty.

The LM2 seems to be setup to warmup up relatively quickly for a diesel. I've been monitoring various temps with Torque app and it shows the exhaust temps inc DPF get to 400+F pretty fast (5 min maybe). Oil temp seems to get to 180-190 about the same time as the LT1 in my Camaro. Coolant temp takes longer to get hot though but I think that is by design in the active cooling system. It seems LM2 is setup to get emissions equipment up to temp quickly.

 

Agreed that a lot of short trips are prob not ideal for any diesel though. If you have a lot of short trips I'd make a point to get it out on the highway occasionally to let everything get hot. I had a 2013 VW Passat TDI 2.0 when I had a 100+ mile daily round trip. That TDI was known to have frequent turbo failures, but my car never did and I think it was because everything got fully up to temp with almost no short trips. 

Posted
4 hours ago, HondaHawkGT said:

The best way to destroy a modern diesel is to start it up, drive a few miles, and shut it back down. I watched a guy with a Ram 1500 Ecodiesel destroy two engines plus exhaust system doing that. He's drive across town to work every day. If you have a habit of doing short drives like that, diesels with modern emissions systems are not for you.

I don't necessarily disagree that this was a factor in older diesel engines, however if this was a legitimate concern for GM, why would they have installed the Autostop feature on the diesels??? 

If you have a 30 mile city commute, the truck could be turning off and on 20 times in 1 commute...

I tend to believe with the technology in the engines today, run time isn't a big factor. 

Posted
5 hours ago, HondaHawkGT said:

The best way to destroy a modern diesel is to start it up, drive a few miles, and shut it back down. I watched a guy with a Ram 1500 Ecodiesel destroy two engines plus exhaust system doing that. He's drive across town to work every day. If you have a habit of doing short drives like that, diesels with modern emissions systems are not for you.

That’s not what I want to hear! I’ve always seen diesel trucks sitting there idling and not turned off at stops some and wondered if the new engines should still do that?
 

I’m curious about why it’s the case that short trips are bad for the engines. 

Posted
3 minutes ago, Duramax3oh said:

That’s not what I want to hear! I’ve always seen diesel trucks sitting there idling and not turned off at stops some and wondered if the new engines should still do that?
 

I’m curious about why it’s the case that short trips are bad for the engines. 

Because water is a byproduct of combustion, and water will condense out of the exhaust stream when the engine and exhaust or not hot enough.

This is true for both gas and diesel engines.

 

It's not the start and stop that causes the problem -- it's the cold running / not running long enough to get warmed up enough that the moisture can be carried out. 

 

 

 

 

 

  • Like 1
  • Thanks 1
Posted (edited)
3 hours ago, becker87 said:

I see very similar numbers with mine at speeds above 75 but seem to get around 25-26 at 65-70. I do have larger and much heavier duratracs on mine though. Thinking of switching back to a lighter tire for summer driving. Even with the heavier tires but with this warmer weather still seeing about 22 mpg in town, granted it's small town driving

Sent from my Pixel 2 using Tapatalk
 

I was pleasantly surprised by the 75-80mph numbers, good to know those do somewhat hold up. 
 

what size Duratracs do you have? I’m looking at adding a level with 275/65R20 which seem to run ~15lbs heavier than stock.
 

Guess I could live with about 25mpg Highway figures at typical speeds but getting up to the 30’s is so incredibly satisfying!!

 

ETA - From an earlier comment... yes I-10 is a very very flat drive. Highest elevation we get is on the overpasses ? 

Edited by Duramax3oh
Posted
6 hours ago, HondaHawkGT said:

The best way to destroy a modern diesel is to start it up, drive a few miles, and shut it back down. I watched a guy with a Ram 1500 Ecodiesel destroy two engines plus exhaust system doing that. He's drive across town to work every day. If you have a habit of doing short drives like that, diesels with modern emissions systems are not for you.

I do not think a 22 mile drive is a short drive, unless you think it is for a diesel engine.

Posted
14 minutes ago, jaslon said:

I do not think a 22 mile drive is a short drive, unless you think it is for a diesel engine.

Nope not saying it is. Just wanted to throw that in there just in case he or anyone else thinking about getting a truck with this engine does a lot of short trips.

Posted
1 hour ago, tvette1993 said:

I don't necessarily disagree that this was a factor in older diesel engines, however if this was a legitimate concern for GM, why would they have installed the Autostop feature on the diesels??? 

If you have a 30 mile city commute, the truck could be turning off and on 20 times in 1 commute...

I tend to believe with the technology in the engines today, run time isn't a big factor. 

 

The autostop shutting off the engine for 30 or 60 seconds isn't the same as hopping in a cold truck and driving for 5 minutes, getting to the destination, and letting it sit 8+ hours. Doing that 5 or 6 days a week, the exhaust system never gets hot enough to keep the exhaust system cleaned out. The Ecodiesel guy was constantly going into regen because 90% of his driving consisted of in-town strolls and short trips. 

 

The autostop feature shouldn't be on this engine IMO, but most guys won't own the truck long enough for the consequences of letting the engine turn off and on like that. GM knows that too (as do all vehicle manufacturers forced to use autostop these days). 

Posted
4 hours ago, Whipped500 said:

I agree and understand this but I think 20 miles is plenty fine. This is why my LML has such low miles. I bought it to tow the boat and I only drive it if I know it will get up to operating temp. 

 

I have a LM2 on order and will be using it for a service vehicle. Some days I drive a mile or two to a customer then have multiple ones blocks apart from there...other days I drive 20+ miles before I get to the first one. I'm hoping that the cooling system gets things to temp faster as they describe it to do. If not, it's under warranty.

 Yeah 20 mile trips are fine. I mainly meant it as a cautionary thing for anyone considering the LM2 and are kind unsure about it. Some people do a ton of short trips in these newer diesels and end up with a ton of problems because they don't understand just how bad it is for the expensive filters on these things.

Posted

Autostop doesn't work til the engine is warmed up. 

 

Therefore, not a factor with the cold start/short trip issue. 

 

 

OTOH, ecodiesel had so many problems they stopped selling them.  

Hopefully for the RAM fans a similar level of issues doesn't occur this time around.

 

 

Posted (edited)
3 hours ago, Duramax3oh said:

That’s not what I want to hear! I’ve always seen diesel trucks sitting there idling and not turned off at stops some and wondered if the new engines should still do that?
 

I’m curious about why it’s the case that short trips are bad for the engines. 

 

Short trips are bad for modern diesels especially.  Higher regen frequency, less chance for the DPF to burn properly due to low exhaust heat/temps present.  It can load up a filter for the worse if the DPF can't burn itself clean correctly.  Also, can load up the emissions sensors and foul them out prematurely.    

 

My 2016 Colorado diesel did great.  I'd let it idle in the winter to warm up sure, but my drive to work is 16 miles one way, 85% highway.  Plenty of time to get everything happy. 

Edited by newdude
Posted
I was pleasantly surprised by the 75-80mph numbers, good to know those do somewhat hold up. 
 
what size Duratracs do you have? I’m looking at adding a level with 275/65R20 which seem to run ~15lbs heavier than stock.
 
Guess I could live with about 25mpg Highway figures at typical speeds but getting up to the 30’s is so incredibly satisfying!!
 
ETA - From an earlier comment... yes I-10 is a very very flat drive. Highest elevation we get is on the overpasses [emoji38] 
I am running 275/70/18 10 ply. Think they were a 33.1 inch tire. I have a two inch level with two inch rear blocks as well

Sent from my Pixel 2 using Tapatalk

  • Thanks 1
Posted (edited)
6 hours ago, HondaHawkGT said:

 

...

The autostop feature shouldn't be on this engine IMO, but most guys won't own the truck long enough for the consequences of letting the engine turn off and on like that. GM knows that too (as do all vehicle manufacturers forced to use autostop these days). 

I wouldn't mind the autostop feature if there was an integrated starter/generator, like in some Mercedes models.

No starter as we know it anymore.

And it can be used for a little boost for acceleration. Pretty much like the RAM E-torque system. Just better ?

 

so long

j-ten-ner

 

EDIT: ...but first I'd like to see self levelling headlights in our trucks......or maybe both...lol

Edited by j-ten-ner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,758
    Total Members
    8,960
    Most Online
    Randy Ginoza
    Newest Member
    Randy Ginoza
    Joined
  • Who's Online   4 Members, 0 Anonymous, 1,858 Guests (See full list)


  • Latest Articles

  • Posts

    • Monday looks like a good day for the dealer to test an ac issue. Hopefully it all turns out good.
    • Paid $2.72 for E85 today.
    • Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • 2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...