Jump to content

Washer Fluid

GN2018
 Share

Recommended Posts

GN2018 Enthusiast

GN2018

Posted
Posted

Does anyone change their washer fluid for the change in season?  I have a fluid in the truck now that is good for cleaning bugs off the windshield.  It’s getting to be winter up her in Michigan and I want to put a fluid in that is good at defrosting the windshield.  I don’t want to just mix the two because I’d just be diluting one of the properties I want.  In this case the defrost.  Problem is, I think it would be a pain to try to drain the reservoir and I don’t really want to waste it by spraying it until it’s gone not to mention the extra wear on the pump.

 

Is there an easy way to swap out the fluid?

16LT4 Enthusiast

16LT4

Posted
Posted

Yes... use it.  Or suction.  The biggest thing to look at is the freezing temp.

 

I'm guessing you currently have the Green Rain-x Bug stuff?  It freezes at 32*, so I'd look to have it out before sustained freezing temps.  The Winter (orange) Rain-x also is anti-bug, so I question the need for the green stuff... I'm in the same boat and made that mistake.  I usually clean my windshield daily, so it won't take me long to work through the tank.

  • Like 1
Jacoby Enthusiast

Jacoby

Posted
Posted

This thread is just wow!!,  almost as bad as the one where the guy asked if it was ok to use his spare if he had a lifted truck

 

Dude just use it up. A gallon of washer fluid cost a few bucks. Hit the button for 30 seconds a couple times a day and the reservoir will be empty in no time. You’re not hurting the pump. 

g2full Enthusiast

g2full

Posted
Posted

RainX makes a 3 in 1 or whatever fluid. Bug off, defrost, and then the rainx solution. It's orange. Get that one.

  • Like 2
GN2018 Enthusiast

GN2018

Posted
  • Author
Posted

I haven’t tried RainX in a while, but the last time I used it, I didn’t like it.  It seemed to leave a coating on the windshield (as it’s supposed to) that made my wipers chatter.  Kind of like they do if you turn them on dry or as if something sticky was on the windshield.  
 

Maybe I can find a multi function solution without the RainX.  I didn’t know they made multi function fluid.  I guess I need to get out more.

  • Like 1
  • Haha 1
g2full Enthusiast

g2full

Posted
Posted
31 minutes ago, GN2018 said:

I haven’t tried RainX in a while, but the last time I used it, I didn’t like it.  It seemed to leave a coating on the windshield (as it’s supposed to) that made my wipers chatter.  Kind of like they do if you turn them on dry or as if something sticky was on the windshield.  
 

Maybe I can find a multi function solution without the RainX.  I didn’t know they made multi function fluid.  I guess I need to get out more.

 

You aren't the first person I've heard say about issues with the RainX and wiper chatter. I never had issues with it. I do know when I worked in the A/M world we use to have people come in and complain that the wax would build up on their washer fluid level sensor and cause issues. I do know in my old corolla before I got rid of it the tank was completely orange from the stuff. So I can respect some people don't have luck with it.

 

Another question though... working in the OE world now and my wife having a Pilot until recently I know that Honda's of most years DO NOT like A/M wipers. No matter what you seem to do they'll chatter. Worst noise ever, and I'd go down the road without the wipers as much as I could. Drove her nuts... anyways.. put OE blades on it, and problem solved. ?‍♂️

  • Like 1
dieselfan1 Senior Enthusiast

dieselfan1

Posted
Posted (edited)
2 hours ago, Jacoby said:

This thread is just wow!!,  almost as bad as the one where the guy asked if it was ok to use his spare if he had a lifted truck

 

Dude just use it up. A gallon of washer fluid cost a few bucks. Hit the button for 30 seconds a couple times a day and the reservoir will be empty in no time. You’re not hurting the pump. 

Unbelievable. First year driving?

Wear the pump out??

This is as bad as the guy wondering about the slide in camper.?

Or the air filter thread.

Edited by dieselfan1
  • Haha 1
diyer2 Senior Enthusiast

diyer2

Posted
Posted (edited)

Hey I have anal thoughts sometimes also.

I have questioned and done things in my 65 years that some people would say lock him up.

It comes with caring and pride of ownwership IMO.

 

I have used the RainX orange for years.

Goodyear blades from Costco on sale for $3- $4 for years.

 

:)

Edited by diyer2
  • Like 1
GN2018 Enthusiast

GN2018

Posted
  • Author
Posted
51 minutes ago, dieselfan1 said:

Unbelievable. First year driving?

Wear the pump out??

This is as bad as the guy wondering about the slide in camper.?

Or the air filter thread.

Close.  Been leasing my cars for about 20 years and haven’t worked on my own car in any fashion in that time.  Now retired, first vehicle I’ve actually owned in a long time and want to do my own work.

 

Last time I worked on a car, the fluid reservoir was maybe a quart.  You sure couldn’t pour an entire gallon in it and the only washer fluid was blue and you just had to make sure you got the one that was good to -25 degrees.  And yes, pumps were crap and it does cross your mind what pumping out a gallon might do.

 

Beyond that, I was wondering if someone might just have an idea where there is an easy to access a hose that I could pull and drain the reservoir easily.  Saving what’s in there wouldn’t have been a bad idea either, but not going to go to too much trouble for that.

 

So, thanks for your help.  Maybe you should find a private club with car geniuses so you don’t have to be encumbered by such ignorance.

g2full Enthusiast

g2full

Posted
Posted
39 minutes ago, GN2018 said:

Close.  Been leasing my cars for about 20 years and haven’t worked on my own car in any fashion in that time.  Now retired, first vehicle I’ve actually owned in a long time and want to do my own work.

 

Last time I worked on a car, the fluid reservoir was maybe a quart.  You sure couldn’t pour an entire gallon in it and the only washer fluid was blue and you just had to make sure you got the one that was good to -25 degrees.  And yes, pumps were crap and it does cross your mind what pumping out a gallon might do.

 

Beyond that, I was wondering if someone might just have an idea where there is an easy to access a hose that I could pull and drain the reservoir easily.  Saving what’s in there wouldn’t have been a bad idea either, but not going to go to too much trouble for that.

 

So, thanks for your help.  Maybe you should find a private club with car geniuses so you don’t have to be encumbered by such ignorance.

I don't think you're crazy for worrying about burning up the pump. I do the same thing.

 

Not positive on the chevys, but it seems that with Honda the pump goes directly in the tank. So to drain the tank easily, you'd have to pull the pump out. But I don't know how the Chevy's are set up. I've never looked. I just spray it for 30 seconds every so often going down the road when I need to drain it.

KARNUT Senior Enthusiast

KARNUT

Posted
Posted

I live in the love bug capital. I keep my washer tank full of washer fluid with antifreeze. I periodically rain ex the windshield. When the bugs are real bad I do one of two things. Usually the dew is so bad in the morning it takes awhile for them to fly. Being retired I run my errands early. Two I keep my water hose ready with bug be gone and rinse the whole front as well as the windshield. I’m more worried about the paint. On trips I’ll find a car wash at the end of the day and rinse. Those bugs in the south will ruin the paint in one night.


Sent from my iPhone using Tapatalk

  • Like 1
Hobey Enthusiast

Hobey

Posted
Posted
44 minutes ago, GN2018 said:

Close.  Been leasing my cars for about 20 years and haven’t worked on my own car in any fashion in that time.  Now retired, first vehicle I’ve actually owned in a long time and want to do my own work.

 

Last time I worked on a car, the fluid reservoir was maybe a quart.  You sure couldn’t pour an entire gallon in it and the only washer fluid was blue and you just had to make sure you got the one that was good to -25 degrees.  And yes, pumps were crap and it does cross your mind what pumping out a gallon might do.

 

Beyond that, I was wondering if someone might just have an idea where there is an easy to access a hose that I could pull and drain the reservoir easily.  Saving what’s in there wouldn’t have been a bad idea either, but not going to go to too much trouble for that.

 

So, thanks for your help.  Maybe you should find a private club with car geniuses so you don’t have to be encumbered by such ignorance.iencumbered

I wonder if you try using a drill pump/hose attachment to siphon the bug juice back out of the washer reservoir!!.. No pump to burn out, and u might be able to get like 95% out ...would only take few minutes....

TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted

I have my washer fluid full of distilled water with a little bit of liquid blue dawn.


Sent from Above

kickass audio Enthusiast

kickass audio

Posted
Posted

I use the winter fluid year round. The only time it gets bad is in the summer when I go on long road trips in the valleys that have a shit load of bugs but the windshield isn't the only thing smeared with dead bodies and blood lol. The bumper especially and the grille/radiator get plastered. I try to get to the carwash to get most of it off and if there is any remaining splatter I just get outside with some paper towels and window cleaner and clean those spots off. 

 

I used to use the cheap summer blend stuff and then switch to the winter stuff in the fall but got tired of having to flush the tank out. I would have my fiance hold the washer button down while I have the hose that leads up to the wiper cowling and have it drain out into the container it came in and reconnect the hose and put the winter stuff in. I really don't use that much washer fluid though. I mostly use it in the winter to see through all the salt that is on the window after the plows are out salting the living hell out of the roads.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.
    • No F-bdy Bs
      SERCICE ESC message?

      By No F-bdy Bs · Posted

      Got this yesterday out of nowhere. Truck is a 25',6.6 gasser with 8k miles.  Only semi anomaly is that the truck had been sitting, uncranked for 6 days. Elec Stability Control showed immediately upon cranking, not while driving. No drivability issues, just the message. Battery didn't seem to be weak when cranking over.  I drove it, killed it, let it sit a few hrs with no avail.  Truck is 100% stock. No damage. 
    • newdude
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By newdude · Posted

      This can be done.  It is not cheap and requires an instrument cluster swap with custom programming, new steering wheel with the controls on it, and a special jumper harness.   The cluster upgrade - 12.3” Digital Cluster Upgrade – 2022.5–2026 Silverado / Sierra (T1 Refresh Pickup) - WAMS   The wheel upgrade - Steering Wheel Upgrade Kit – 2022.5–2026 Silverado / Sierra (T1 Refresh Pickup) - WAMS   The column harness upgrade - 2019 - 2026 Silverado / Sierra: Steering Wheel LIN Bus Harness - Harness Dr. - DIY Done Right     The problem with doing all of this?  You pretty much can't have any programming done to your truck that involves the cluster ever again.  The dealer won't be able to program the cluster as GM's system will only pull data for the cluster the truck came with.  So it would be advised also to turn off over the air updates.   TLDR;  Should have bought an LT double cab?  You'd have a power seat, the wheel controls, the cluster, all things that you've been seeking in your various posts so far about your new WT regular cab.  
    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      I was unaware of that, thanks for updating me.
    • newdude
      2026 TurboMax L3B 2.7L: AFM/DFM present/disablable? [2026 Silverado 1500WT: 4WD RC RB 2.7L]3GCNKAEK9TG345558

      By newdude · Posted

      Yes.  The 2.7 Turbomax has Active Fuel Management.  It is NOT the same as the V8s.  Totally different system.     Here is an article from GM when the 2.7 came out explaining the cylinder deactivation and the valve lift system.  Starts at the section called "SCS Valvetrain":   New Turbocharged 2.7L 4-Cylinder Engine Powers Full-Size Trucks – TechLink         This is an internet myth going around.  It was alleged that some 5.3s had this mystical 8th digit of the VIN as an "E" which somehow meant it had a new one year only 5.3 that didn't have DFM.  The writer of said article and the person that made the claim conveniently can't count because they posted the VIN.  The 8th digit was a "D" which meant its still the 5.3 with DFM.  The 9th digit of the VIN was an "E" and the 9th digit isn't the engine code.  At all.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...