Jump to content

Tightening front shock nut HELP

danmc96
 Share

Recommended Posts

danmc96 Enthusiast

danmc96

Posted
Posted (edited)

I mistakingly removed the nut on top of my front passenger side shock while installing MotoFab front leveling kit. I got everything back together but the shaft spins and I can’t grab it with anything due to it being sunk into frame. Any ideas on what to use to tighten this up?   I’ll try to snap a pic tomorrow. 

Edited by danmc96
davester Senior Enthusiast

davester

Posted
Posted

Typically, the tip of the shock is used to prevent it from rotating.  Some will have provision for an allen key (or something similar), some will have a machined in square or hex to put a wrench on the end.

Ryguy Enthusiast

Ryguy

Posted
Posted

Wait you removed the top strut bolt that holds the spring down? Did you remove it completely? If so you will need to pull the coil over out and use a spring compressor to re-secure the nut.

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

A vise grips with some rubber hose on the ends would work if you can get it to grab on to the shock piston through the coil spring. Then brap it down with an impact gun.

AJMBLAZER Enthusiast

AJMBLAZER

Posted
Posted

I have had good luck with the weight of the truck pushing down on it and the impact going to town.
 

If you are asking how to reassemble a completely apart strut and coil Then yes, you will need some spring compressors.

  • 8 months later...
andrewb24 Enthusiast

andrewb24

Posted
Posted
On 5/16/2020 at 12:51 AM, danmc96 said:

I mistakingly removed the nut on top of my front passenger side shock while installing MotoFab front leveling kit. I got everything back together but the shaft spins and I can’t grab it with anything due to it being sunk into frame. Any ideas on what to use to tighten this up?   I’ll try to snap a pic tomorrow. 

whats the update on this issue? were you talking about the center nut on the strut?

Gangly Senior Enthusiast

Gangly

Posted
Posted

I did the same thing while not paying attention awhile back.  I had to remove the coil and shock from the vehicle to repair it.

  • 3 years later...
rahool82 Enthusiast

rahool82

Posted
Posted (edited)

Can you tell me how you got the spring out? The top of my strut snapped off and I've tried lowering the control arm as far as it'll go but I can't get pressure off it. I'm thinking my only option are the widow maker spring compressors if I can get them in there and cranked down. Looks like it might work but I'm not exactly rushing to try it lol. Any ideas or tips greatly appreciated!!

Edited by rahool82
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted (edited)
4 hours ago, rahool82 said:

Can you tell me how you got the spring out? The top of my strut snapped off and I've tried lowering the control arm as far as it'll go but I can't get pressure off it. I'm thinking my only option are the widow maker spring compressors if I can get them in there and cranked down. Looks like it might work but I'm not exactly rushing to try it lol. Any ideas or tips greatly appreciated!!

With weight on the strut, you can wrap/lace the spring (the weight on it keeps it compressed some) with a heavy gauge wire. The more and tighter you get it laced the safer it will be. It should be enough to hold it all together to get it out of the truck. Unless you have a fancy strut compressor, then the dangerous part of getting the wire off while under tension. At least its not going to damage the truck and its not right in your face either.

 

Out of the truck you could take it to a shop too.

Edited by asilverblazer
rahool82 Enthusiast

rahool82

Posted
Posted (edited)
2 hours ago, asilverblazer said:

With weight on the strut, you can wrap/lace the spring (the weight on it keeps it compressed some) with a heavy gauge wire. The more and tighter you get it laced the safer it will be. It should be enough to hold it all together to get it out of the truck. Unless you have a fancy strut compressor, then the dangerous part of getting the wire off while under tension. At least its not going to damage the truck and its not right in your face either.

 

Out of the truck you could take it to a shop too.

Not a bad idea, might do this in addition to the screw down compressors, just for some extra pieces of mind. Thanks!

 

No fancy spring compressors here, just the old beater rentals from autozone

Edited by rahool82
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted
20 hours ago, rahool82 said:

Not a bad idea, might do this in addition to the screw down compressors, just for some extra pieces of mind. Thanks!

 

No fancy spring compressors here, just the old beater rentals from autozone

Get it out of the truck then using the rent-a-compressor will be easier.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Coastie05
      2027 GMC Sierra: Official Discussion

      By Coastie05 · Posted

      Sure, but they do have some affordable options like the Trax, Trailblazer, Envista, and Encore. Some of these have a cheaper base price than the Civic, though the fuel economy isn’t as high. The main problem is that people WANT the highest trim with all the goodies and finance for like 7 years. That’s how ppl “afford” the more expensive vehicles. 
    • Jsdirt
      07 yukon xl 6.2 stalls at hot idle and wont restart

      By Jsdirt · Posted

      Holy s**t - not much of a parts thrower you say? You BLASTED that thing with the parts cannon!  You'd have been probably $1,000 ahead if you had just brought it to a competent shop rather than shotgunning a bunch of parts it clearly didn't need.   Just FYI - oil additives are really, REALLY good at ONE thing ... and that's emptying your wallet. They're ALL useless gimmicks.   If that has the L94 or L99, then #7 is an AFM cylinder. I'd suspect a failed lifter in that case.   If you leaned on wiring, sensors, and/or connectors while changing the oil, you'll have to check all that to be sure pins didn't get pulled out, connectors broken, etc.. Old wire loom that was barely adequate when new is certainly brittle by year 19 - make sure wires aren't chaffed and shorting out somewhere where you might have leaned. or supported yourself on it.   If your a mechanic, why didn't you just find out what you were missing and troubleshoot from there??  TIMED spark, fuel PSI / injector pulse, air, compression.  Can't make ANY money going the parts cannon route.
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      LOL! Are you joking?? That wax SUCKS! 100% gimmick made to "look" good.    After just TWO winters I had severe surface rusting in patches over 90% of the frame. Only reason it looks great in the pics is because I SATURATED the frame every single fall with used motor oil for 14 of the 16 years I owned it. Otherwise it would've been sent to the crusher 8 years earlier with the speed it was rusting prior!    I sold that POS 3 years ago. Was a gigantic headache the second it rolled off the showroom floor. Brakes pulsated on the TEST DRIVE. Door trim fell off the 1st week! Interior squeaked and rattled, and the drivetrain clunked after 2k miles. 4x4 switch failed shortly after. Front end - ball joints, struts, hub bearings - all failed between 38k-50k. Engine started burning oil at 50k. Rear and and transmission failed before 100k. Nothing but problems, and frustration with the piss-poor engineering designed to make you give up. Well, it worked! Nothing on that truck was easy to remove ... except the wheels. They haven't figured out how to screw that up yet. Give 'em time ...   I won't make that mistake again. EVER.   Such fond memories ... https://postimg.cc/K1qf23tS  https://postimg.cc/gallery/X02z64J  https://postimg.cc/gallery/mHSRXZv  https://postimg.cc/gallery/D4mMRfL
    • davester
      OBD not ready?

      By davester · Posted

      Different monitors do their test only under conditions specific to that monitor.  you MIGHT find the drive cycle conditions for the monitor that isn't ready on this site: https://lemon-manuals.la/   If it's not there, then it should be on alldata.com for your truck, but it requires a paid subscription.   And you need to know which specific monitor isn't ready.
    • RW2018GMC
      Me too……..

      By RW2018GMC · Posted

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...