2014+ Suspension Lifts

Buttercup24 · April 19, 2016

I got the 6'' basic kit as money was an issue for me and the new coil overs, to me, wasn't worth the extra cost. The rear shocks do provide a quality ride so I did go that route.

I was definitely in the same boat, then the new version fox shocks came out and I was just curious. I probably will pick up the fox tears being they are fairly inexpensive

Love your trucks color btw, had a burgundy 01 Silverado and. Red jewel 11' 2ss camaro. Almost went with it again but I needed to break the trend!

NoleLife · April 19, 2016

I've got the Zone 4.5" lift on order, and am sure that it is the size and stance I want. But if I wanted to increase the height in the future, is there a way to easily upgrade from the 4.5 to the 6.5in? Would it just be a larger block and drop for the front that re-uses all the other parts? Or would an entire new kit be needed?

randomposter · April 19, 2016

Turned out great! The wheels look good. They look like they have a pretty deep lip for a 20x9 and positive offset. I might have to switch out my fuel nutz for a set.

Thanks, it seemed like it took me forever to find what I wanted. I like a basic 5 to 6 spoke wheel with some type of lip. I bought the wheels site unseen and am pretty happy with the choice.

randomposter · April 19, 2016

After the lift I put on this past weekend I'm thinking I would like 1"-1 1/2" inches added to the rear. I was debating on doing the Add-A-Leaf with Zone but was unsure if it would stiffen the ride in the rear. Any suggestions?

Robert.jean1 · April 19, 2016

I was definitely in the same boat, then the new version fox shocks came out and I was just curious. I probably will pick up the fox tears being they are fairly inexpensive

Love your trucks color btw, had a burgundy 01 Silverado and. Red jewel 11' 2ss camaro. Almost went with it again but I needed to break the trend!

Thanks I truly love the color also. This is the first non black vehicle I've owned and went to buy another black truck until seeing this one on the lot and immediately knew I had to have it.

skallywag · April 20, 2016

Has anyone done the 6.5" zone or another 6" kit with the bottom spacer left installed from a rcx level? Wondering if i can keep my angles manageable and run the 6.5" the spacer on bottom the aal in the rear and 37x12.50 on my factory 20s

Kennith Pujol · April 20, 2016

Finally got the wheels and tires in. Next week she will be lifted. Pretty damn happy! ?

Kennith Pujol · April 20, 2016

37x13.50 Toyo Open Country MT and 22x12-44 Fuel Maverick D260s

Nab · April 20, 2016

Sweet man. Anytime you get a chance i know how it goes.

Sorry it took so long man we have been busy as hell...

skallywag · April 20, 2016

awesome man that's the 6" right? going to do spacers in the rear to even it out? if so what size?

Bpun2016 · April 21, 2016

Ok finally got through this one after weeks on my phone, screenshot a bunch of pics but still a couple questions.

Im down to the Zone 6.5 and the Fabtech gen II/procomp 6 looking to fit 325/20 or 35x12.5x20. With these which would I be able to use with stock 20 wheels at first and change out later. Obviously theres a huge price difference between zone and fabtech but is there any noticeable difference quality wise. Last question, I think the only one of these that retains the factory track width is the fabtech but ive read the turning radius becomes even worse, any expertise with that?

Thanks for all the help, sad it came to an end after 153 pages

Edit: Also what am I looking to spend install wise in orange county, los angeles, CA (recommended shops if from this area)

Edited April 21, 2016 by Bpun2016

skallywag · April 21, 2016

when i was out there i took mine to outlaw offroad in Santa Ana they were great

BHolland · April 21, 2016

Thanks for all the info in this thread. I ended up with the following setup.

4.5" Zone suspension lift

20x9 (+10 offset) Hostile Hammered Wheels

33x12.5/20 Toyo Open Country MTs

1.5" Wheel spacers in the rear

Before:

Just the lift without wheels (looks lower in the rear because I had all my factory parts and crap in the bed weighing it down):

After:

Your truck looks great. In the pic with the factory wheels, did you have the 1.5 inch rear spacers on? Also, does the 4.5 inch Zone still leave a slight bit of rake?

Gonzalez210 · April 21, 2016

37x13.50 Toyo Open Country MT and 22x12-44 Fuel Maverick D260s

what size lift are you going with? Edited April 21, 2016 by Gonzalez210

randomposter · April 21, 2016

Your truck looks great. In the pic with the factory wheels, did you have the 1.5 inch rear spacers on? Also, does the 4.5 inch Zone still leave a slight bit of rake?

Thanks... Are you talking about the 1.5" spacers I added to the wheel or the factory 1.5" block since your mentioning the rake?

There is no rake with the 4.5" zone. I'm thinking about going the add-a-leaf route in case I ever haul anything I'm not a fan of the squatting look. The way it sits without anything it seems perfectly level from front to back.

Edited April 21, 2016 by randomposter