Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

lobstermen Enthusiast

lobstermen

Posted
Posted

I went from my stock 265/65/r18 tires to duratrac 275/60/r20s with oe all terrain rims. My average mpg went from 19 to 13. Now I did not truck recalibrate my truck for these bigger tires. So I assume the average mpg on trucks computer is off a bit? On the highway yesterday truck would stay in v8 mode 90 % of the time. My question is whether this is about the same everyone else is seeing? I was expecting about a 2-3 mpg loss. But 6 seems like alot.

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

graves_7 Enthusiast

graves_7

Posted
Posted

I went from my stock 265/65/r18 tires to duratrac 275/60/r20s with oe all terrain rims. My average mpg went from 19 to 13. Now I did not truck recalibrate my truck for these bigger tires. So I assume the average mpg on trucks computer is off a bit? On the highway yesterday truck would stay in v8 mode 90 % of the time. My question is whether this is about the same everyone else is seeing? I was expecting about a 2-3 mpg loss. But 6 seems like alot.

I have a p275/60r20 on 20x9 XD Addict wheels and I averaged 16.3 MPG's on my last tank of fuel (hand calculated so it is accurate). I have some cheapo Pathfinder S/AT tires that Kumho makes for Discount Tire that I purchased for my old truck because I knew I was going to trade it then I ended up keeping the wheels and tires for my 2014 Sierra. It is hard to find any specs on my tires but I believe they weigh around 45lbs (looks like the Duratracs weigh around 48lbs) and my wheels are around 31lbs each (not sure what the factory wheels weigh). I drive mostly city...I have a 10 mile stretch on my way to work that is a 4 lane, but it has occasional red lights I hit. I also towed two ATV's on my trailer for about 15 miles on that tank of gas.

Yamiryder Enthusiast

Yamiryder

Posted
Posted

Ok guys, any help is appreciated....I have a dilemma between going 295/70/18(unknown fitment) vs 275/70/18(known to fit easily).

 

My setup is 2014 Sierra A/T Double Cab with RCX 2.5" kit.

 

My question is geared towards the 295/70/18... how bad will I rub on 18x9 +12 ? What 18x9 wheel offset would work?

I see some guys doing 295/60/20, on the 2.5" kit, and that measures about .25" shorter than the 295/70/18.

 

I just don't wanna invest that kinda cash and not be satisfied with overall width and height of the tire. 275/70/18 just doesn't seem like a large enough increase to justify. I don't really wanna go to a 20" wheel for overall ride quality and the look just isn't for me, I like meaty sidewalls. Any input is appreciated, I'm ready to pull the trigger.

I felt the exact same way. I'm going with 295/70/17's. Could have gone 33x12.50x18, but for some reason, the standard sizes cost way more per tire and I refuse to pay that price haha.
  • Like 1
abronstrup21 Enthusiast

abronstrup21

Posted
Posted

I have a 2015 Sierra Denali and I just put the 2.5" RC level kit on the front. I didn't add the rear block because it sits almost perfectly level now. The problem I have is that it rides like a dump truck now. The front is really tight and bouncy. It has been aligned professionally and everything but the ride is definitely worse than I had anticipated. Anyone else have this problem? The truck does have the factory 22" wheels and the side wall of the tire is pretty low profile but this has me thinking of taking it off completely. Any suggestions because Rough Country said they had never heard of this before?!

No Tyme Senior Enthusiast

No Tyme

Posted
Posted

I have a 2015 Sierra Denali and I just put the 2.5" RC level kit on the front. I didn't add the rear block because it sits almost perfectly level now. The problem I have is that it rides like a dump truck now. The front is really tight and bouncy. It has been aligned professionally and everything but the ride is definitely worse than I had anticipated. Anyone else have this problem? The truck does have the factory 22" wheels and the side wall of the tire is pretty low profile but this has me thinking of taking it off completely. Any suggestions because Rough Country said they had never heard of this before?!

 

 

I have a 2015 Sierra Denali and I just put the 2.5" RC level kit on the front. I didn't add the rear block because it sits almost perfectly level now. The problem I have is that it rides like a dump truck now. The front is really tight and bouncy. It has been aligned professionally and everything but the ride is definitely worse than I had anticipated. Anyone else have this problem? The truck does have the factory 22" wheels and the side wall of the tire is pretty low profile but this has me thinking of taking it off completely. Any suggestions because Rough Country said they had never heard of this before?!

My 2014 LT Crew 4X4 has the RC 2 1/2" level/lift kit with complete install and I will agree that the front end seems stiffer and that the back seems mushy. I was thinking of trying the Rancho shocks on the rear of my LT to see if that would change (stiffen) things in the rear. I know it would effect the ride quality...

I have also given some thought to pulling out the upper spacer to reduce it to a 2" level kit since it's .5" and only gives you .5" of lift. Keep us informed.

  • Like 1
CptMcSaug Enthusiast

CptMcSaug

Posted
Posted

This is the ready lift 2.25 in the front and 2 in block in the rear

 

Before

20141109_125707.jpg

 

After

20150112_144140.jpg

 

UPDATE With Tires

275/65r20 Cooper ST Maxx

20150114_155408.jpg

How's the ride?
tanner709 Enthusiast

tanner709

Posted
Posted

I have 295/70x70 with a +18 offset i havent trimmed anything and thats with the 2.5 rc kit , i could have gone a bit bigger i think youll be fine with a 295/70x18

Nice truck, I like those wheels and still haven't confirmed kmc vs method yet. I like the setup but 295/70/17 and 295/70/18 differ by 1" in height. Do you have more than a 1/2" of clearance at all points around your tire ?

abronstrup21 Enthusiast

abronstrup21

Posted
Posted

 

I have a 2015 Sierra Denali and I just put the 2.5" RC level kit on the front. I didn't add the rear block because it sits almost perfectly level now. The problem I have is that it rides like a dump truck now. The front is really tight and bouncy. It has been aligned professionally and everything but the ride is definitely worse than I had anticipated. Anyone else have this problem? The truck does have the factory 22" wheels and the side wall of the tire is pretty low profile but this has me thinking of taking it off completely. Any suggestions because Rough Country said they had never heard of this before?!

 

 

My 2014 LT Crew 4X4 has the RC 2 1/2" level/lift kit with complete install and I will agree that the front end seems stiffer and that the back seems mushy. I was thinking of trying the Rancho shocks on the rear of my LT to see if that would change (stiffen) things in the rear. I know it would effect the ride quality...

I have also given some thought to pulling out the upper spacer to reduce it to a 2" level kit since it's .5" and only gives you .5" of lift. Keep us informed.

 

 

 

I have a 2015 Sierra Denali and I just put the 2.5" RC level kit on the front. I didn't add the rear block because it sits almost perfectly level now. The problem I have is that it rides like a dump truck now. The front is really tight and bouncy. It has been aligned professionally and everything but the ride is definitely worse than I had anticipated. Anyone else have this problem? The truck does have the factory 22" wheels and the side wall of the tire is pretty low profile but this has me thinking of taking it off completely. Any suggestions because Rough Country said they had never heard of this before?!

 

 

My 2014 LT Crew 4X4 has the RC 2 1/2" level/lift kit with complete install and I will agree that the front end seems stiffer and that the back seems mushy. I was thinking of trying the Rancho shocks on the rear of my LT to see if that would change (stiffen) things in the rear. I know it would effect the ride quality...

I have also given some thought to pulling out the upper spacer to reduce it to a 2" level kit since it's .5" and only gives you .5" of lift. Keep us informed.

 

Did you add the rear blocks as well? It doesn't appear is if you did. I am also thinking of taking the front .5" spacer to help with ride quality. If you do this soon, let me know how it changes things. Thanks

MattUofM Enthusiast

MattUofM

Posted
Posted

here is a the radylift leveling kit. think this one is 2.5in. anyway i drove it around and it seems to ride and drive nice. the only place i feel it is stiffer is on larger bumps. anyway, i think we are going to start making this a "package for the all-terrains that we get in. make them the way they should come from the factory. leveled and bfgoodrich m2's

IMG_20150128_080632_zpsdj27lyel.jpg

  • Like 1
5RWill Enthusiast

5RWill

Posted
Posted

here is a the radylift leveling kit. think this one is 2.5in. anyway i drove it around and it seems to ride and drive nice. the only place i feel it is stiffer is on larger bumps. anyway, i think we are going to start making this a "package for the all-terrains that we get in. make them the way they should come from the factory. leveled and bfgoodrich m2's

IMG_20150128_080632_zpsdj27lyel.jpg

 

Those look like KO2s, here is the M2. Still great looking truck. I wish i would've gotten the all terrain just for the rims, then debadged it.

chrome_mo951_bfg_km2_35x12_5x17_002.jpg

  • Like 1
bubaloo1983 Enthusiast

bubaloo1983

Posted
Posted

is anyone running the 3 inch body lift, with a level and 35s?

 

Im thinking about this set up as my final specs. im running a 2 inch level on slightly larger then stock tires now. it just isn't high enough for me lol :)

if you do can you post pics please. thanks!

Jim31 Enthusiast

Jim31

Posted
Posted

OK,

I really like the stock height of my truck.

Do not want to change it.

BUT, I would like to get more rubber between my rims and the road.

So, with just a leveling kit, no raising the rear, what kit would that be?

 

Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • parthery
      GM Hard Folding Tonneau by REV review

      By parthery · Posted

      Some clarification may help with some of these issues.   - Rev Industries is/was the division of BAK (now Realtruck) that makes covers under the OEM names.  So if you see one with a Ford logo on it, or if you are buying the GM Accessories cover, you are essentially buying a BAK G2 cover with different branding.   - Rev Industries now markets under RealTruck "Advantage."   - As of May 1, 2025, the Advantage covers now have a 5 year warranty.  Anything before that was a 36/36K warranty.   - Parts for the covers are available from Realtruck or BAK.  The email address to reach them is [email protected] or you can call them at 818-365-9000   - If the entire cover has to be replaced, you have to go through your local GM dealer.  Service dept opens an RO, notes the damage and submits it as a warranty claim.  Keep your paperwork handy so they can confirm when you purchased it and it's within the warranty timeframe.  Once the warranty claim is approved, Parts orders the replacement cover.  When it arrives at the dealership, service will remove and install the new one for free as labor is included under warranty.   - The Advantage covers are not the latest and greatest Gen 3 covers.  They still use the old school clamps, elevator bolts, etc...If you want the newer technology, consider buying your cover in the aftermarket world.  That way, if you have an issue you can deal directly with the manufacturer.   - Finally, RealTruck has a program with many of their authorized dealers that doubles the warranty to 10 years if the authorized dealer does the install.     Hope this helps.
    • parthery
      Upgrade to a 2026 AT4 with the 3.0L Duramax

      By parthery · Posted

      Welcome to the group!  My '22 just crossed 150K miles.  Runs perfectly.  Oil pump belt will be done in the next 30 days or so and onward hopefully for another 150K.  Love the truck.
    • richard wysong
      Needing this part.

      By richard wysong · Posted

      Still looks like a rivet to me in the pics, I don't see a nut and none of the pics show the head of the screw. But if you says so.....
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks for all the help so far!   I did try right from 2026 right down to 2021, and only from 2023 down lets me select the option for tire psi change, but I get the vehicle not supported error!   I'll definitely try it under Chevrolet after work today, and I'll get the sensor number from gm for my truck tire sensors. And I'll let you know if it works for me under Chevrolet!   And if that doesn't work, I'm going to guess that what @Atlas said about maybe I have a different body control module could be true!  
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...