What have you done to your K2 today?

[Waterfowler41]

Is that the DeeZee one?

 

I need to do something for carrying my canoe. I'm not ready to just do the foam blocks on the roof yet.

I made an install and review video. Especially for canoe/kayak hauling this rack system comes off really easy for storage.

 

 

 

 

Sent from my iPhone using Tapatalk

[RoadWins]

Making my Black 2017 Z71 just a little blacker

 

Vinyl Sticker for the steering wheel

 

Masked it off

 

Sprayed with Plasti Dip

 

Think it came out pretty good.

[SilveradoSaver]

Making my Black 2017 Z71 just a little blacker

 

Steering Wheel.jpg

Vinyl Sticker for the steering wheel

 

Wheel 2.jpg

Masked it off

 

Wheel 3.jpg

Sprayed with Plasti Dip

 

Wheel 4.jpg

Think it came out pretty good.

 

 

I'm pretty decent with Plastidip, but when I tried to do the small bowties on my old wheels it turned out like crap lol. Good job on yours. I also tried to do the steering wheel bowtie with Plastidip; same result. I should look into using vinyl like you did.

[RoadWins]

 

 

I'm pretty decent with Plastidip, but when I tried to do the small bowties on my old wheels it turned out like crap lol. Good job on yours. I also tried to do the steering wheel bowtie with Plastidip; same result. I should look into using vinyl like you did.

 

I bought a precut bowtie for the steering wheel. lucky it came with 2. Second time I peeled it off the backing then re-stuck it on the backing with only about 1/2 of the sticker on the backing. That let me adjust it till I had it just right. Then peeled the other half off. On the plasti dip I taped each line individually. I found that was a whole lot easier than trying to cut out the bowtie.

 

 

 

[SilveradoSaver]

 

I bought a precut bowtie for the steering wheel. lucky it came with 2. Second time I peeled it off the backing then re-stuck it on the backing with only about 1/2 of the sticker on the backing. That let me adjust it till I had it just right. Then peeled the other half off. On the plasti dip I taped each line individually. I found that was a whole lot easier than trying to cut out the bowtie.

 

Wheel 6.JPG

 

 

Wheel 5.jpg

Thanks for the tip. I also taped off each line too but I think I rushed it. Oh well; I have aftermarket wheels now lol.

[Barman84]

Today. I put in an AAL and a half inch shackle on the rear and a 1.5" level up front on top of my 6" skyjacker lift. Deleted the muffler it sounds ok but not overly loud but not loud enough which is weird. I'm going to open the flapper valve and see if that makes any changes or not. Or I might just get rid of the resonator to and put a magnoflow one in its place not sure yet. Overall my tears up now 7.5" and my fronts up 7.5". I don't like a leveled lifted truck when I haul my motorcycle I don't like the way it was squated JB the back at all. Rides. It bad with the AAL and pulling my 22 foot ski boat it looked just perfect finally instead of looking like I had a 1k tongue weight on my trailer. It's 550 but dang.

[Abearclaw]

 

 

Sent from my iPhone using Tapatalk

[Static]

Today. I put in an AAL and a half inch shackle on the rear and a 1.5" level up front on top of my 6" skyjacker lift. Deleted the muffler it sounds ok but not overly loud but not loud enough which is weird. I'm going to open the flapper valve and see if that makes any changes or not. Or I might just get rid of the resonator to and put a magnoflow one in its place not sure yet. Overall my tears up now 7.5" and my fronts up 7.5". I don't like a leveled lifted truck when I haul my motorcycle I don't like the way it was squated JB the back at all. Rides. It bad with the AAL and pulling my 22 foot ski boat it looked just perfect finally instead of looking like I had a 1k tongue weight on my trailer. It's 550 but dang.

[6.2Midnight]

...

[Bmz72]

 

 

Sent from my iPhone using Tapatalk

[cbrsilv15]

Took 10 mins and installed my grab handle.

 

 

The instructions are very unclear. I just removed the tether all together. Just pull down to keep a constant pressure on it and insert the screwdriver in all 4 slots. Just like the one in this pic.

 

[slj2008]

Making my Black 2017 Z71 just a little blacker

 

Steering Wheel.jpg

Vinyl Sticker for the steering wheel

 

Wheel 2.jpg

Masked it off

 

Wheel 3.jpg

Sprayed with Plasti Dip

 

Wheel 4.jpg

Think it came out pretty good.

looks good. where did you get the steering wheel decal from ????

[smcgillis10]

Cleaning my intake valves. 67k miles. First time it's been done. Need to find some to Walnut blast them. The B12 chem tool worked alright.

 

Sent from my Pixel XL using Tapatalk

[ShamrockShooter]

Removed rear seats (crew cab) and carpet and installed dynamat and pad. 9 hours later it's all back together.

 

Sent from my SM-G930V using Tapatalk

[cbrsilv15]

Where'd you pick up the dynamat? I need to get some to start inside my truck when I have the back seat out.