WTB: Diablo Intune i1000 or Trinity T1000
-
Similar Content
-
Diablosport inTune i3 8246 Platinum Tuner - $350 Shipped
By erodriguez24,
- diablosport tuner
- Silverado
- (and 3 more)
- 0 replies
- 1,754 views
-
- 1 reply
- 1,445 views
-
- 3 replies
- 2,642 views
-
Parts for 2014-2018 Sierra or Silverado1 For Sale!!!!!!! 1 2
By Csjumper2003,
- diablosport
- kicker
- (and 9 more)
- 20 replies
- 5,329 views
-
- 5 replies
- 2,782 views
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
250.4k
Total Topics2.7m
Total Posts -
Member Statistics
342,835
Total Members8,960
Most Online
-
Who's Online 10 Members, 0 Anonymous, 578 Guests (See full list)
-
Latest Articles
-
Posts
-
By Texasdeere · Posted
I've put a few thousand miles on the truck and it seems to have settled where it should be. The stance looks right to me now. Before it was a little lower in the front. The truck has 133K on it. I can put a tape on it if you want some numbers. -
From what I’ve read, yes, that would be the best thing to do. However, it is very expensive and there’s no guarantee that the lifters will actually fail, especially if you’re not going to keep the truck for its entire useful life. My plan is to wait until I hear a lifter go bad and hope I can catch it without it being a catastrophic failure. At that point, they have to open up the engine anyway so that’s when I’d mechanically eliminate the AFM. Plus, there is a 5 year 60K mile warranty on the drive train. I have an extended warranty so I’m good until March of 2027, so I’m certainly not doing anything mechanical before then. I do have the Range disabler and I change the oil way sooner than suggested hoping that will get me into the 100K mile mark at which point, I may sell the truck. I don’t drive much. My ‘21 has 48K miles on it so to get to 100K miles will probably take another 5 years. Probably more because I drive less now than the first few years of ownership. -
By Hoginedgewood · Posted
Was looking at new trucks online, only the upper models advertise a 2 speed? Maybe I read it wrong. -
Yeah, its not an instruction anywhere but instead a unofficial shortcut that some, including myself, use. It does take considerable leverage against the exhaust crossover to allow enough room to clear the pans, but it doesn't strain it any more than normal driveline torqueing of the exhaust pipe and components. -
And there aren't any "bellows". There are solid plastic doors the actuators move, which largely seal just by themselves, and then have a strip of foam around the edge to better seal the door. The foam does deteriorate over time, but this is unlikely to be a significant cause of the problem.
-
-
GM-Trucks.com Clubs
-
Black Truck Club
Open Club · 612 members
-
White Truck Club
Open Club · 380 members
-
Canadian Owners Club
Open Club · 282 members
-
Red Truck Club
Open Club · 157 members
-
diesel 3.0
Open Club · 281 members
-
Texas Owner's Group
Open Club · 371 members
-
NorthSky Blue Club
Open Club · 118 members
-
Midwest Owner's Group
Open Club · 213 members
-
2015 Custom Sport Club
Open Club · 5 members
-
GM Snow Plowing Club HD
Closed Club · 14 members
-
-
Popular Contributors
-
.thumb.JPG.2c573de60d3a3a4407c7d92298db46dd.JPG)
Recommended Posts
Archived
This topic is now archived and is closed to further replies.