Jump to content

Bilstein shocks thread

yanzhixiang

By yanzhixiang
in Modifications & Accessories

 Share

Recommended Posts

2kwik4u Enthusiast

2kwik4u

Posted
Posted
10 hours ago, KJS Sullivan said:

I just saw the Bilstein 5100 set of 4 for $294 free shipping on Amazon oh, FYI all you guys

Got a link to it? I can't find them anywhere on amazon as a set. Especially for that price.

  • Replies 2.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bwilloby46
bwilloby46

I put the bilstein 5100s on the rear of my 14 High Country with a new 2" block a few weeks ago. Ride is unbelievable compared to stock. Liked it so much I got the adjustable 5100s for my front, remove

schloppy
schloppy

Hello, I'm not new to the forum but I just joined and figured I'd contribute to the community.   2016 Silverado 1500 "Z71" removed rancho's and swapped with Bilstein 5100's all around. So after d

Jullian is not my name
Jullian is not my name

I just got done with installing my 6112's on my 2014 GMC Sierra Crew Cab.  Reading some install guides on here really helped, along with printing some Chilton Repair guide torque specs that I got from

Posted Images

Yondu Enthusiast

Yondu

Posted
Posted
54 minutes ago, 2kwik4u said:

Sounds like the 5100's are the way to go. Would I just leave them on the lowest setting, or is there a "middle setting" that results in no lift/drop?

 

My biggest complaint with the Ranchos is the "bounce" after the hit. Most noticeable on sharp edged bumps like expansion joints and things like that. It's almost as if there is NO rebound damping, and only bound damping. Hit the bump and there is a noticeable procession after the initial hit. Feels like there are 3-4 more oscillations in the suspension before it comes to rest. The low shaft speed damping seems OK as the truck doesn't float or bounce excessively, but the high shaft speed damping is off and makes the truck to stiff overall.

 

With any luck the 5100's will cure some of that. I'm nervous on going to a P tire as I tow a LOT in the summer. 2 trips a week on average to the lake with a 5,200lb boat, 4 people, coolers, etc. Don't want to get a set of tires that tow "squishy". Had P tires on my '03 Yukon, swapped to LT tires and the towing got much better immediately.......I'll go read some other threads on that though :D

The lowest setting will give you 0 lift or drop. In theory it should give you the best and softest right as well, but I've only tried the third setting which is a 1.25 inch lift.

 

The Bilstein will fix that bounce and wallow you get after you had a big bomb. They didn't work miracles like some people reported in my opinion, but they were a definite improvement. My truck also had under a thousand Miles when I put them on. 

 

As for LT tires even a p rated tire exceeds our trucks rated capability, but I'm sure not all tires are created equal as far as ride quality and towing confidence. I'd only want LT tires if I offroaded and was afraid of my tires getting cut by sharp rocks, or I had a 3/4 ton.  I don't have a ton of experience towing though what size tire and rim size were you using? Extra wide tires would definitely describe the problem you were having as well. 

2kwik4u Enthusiast

2kwik4u

Posted
Posted
2 minutes ago, Yondu said:

The lowest setting will give you 0 lift or drop. In theory it should give you the best and softest right as well, but I've only tried the third setting which is a 1.25 inch lift.

 

The Bilstein will fix that bounce and wallow you get after you had a big bomb. They didn't work miracles like some people reported in my opinion, but they were a definite improvement. My truck also had under a thousand Miles when I put them on. 

 

As for LT tires even a p rated tire exceeds our trucks rated capability, but I'm sure not all tires are created equal as far as ride quality and towing confidence. I'd only want LT tires if I offroaded and was afraid of my tires getting cut by sharp rocks, or I had a 3/4 ton.  I don't have a ton of experience towing though what size tire and rim size were you using? Extra wide tires would definitely describe the problem you were having as well. 

Thanks for the info on the shocks. 

 

I can't remember the tire size on the Yukon. They were stock size as best as I can tell. I also moved to a 17in rim from a 16in rim at the same time. That might also have contributed to the increased stiffness, hadn't thought about that until now. I'll have to check the axle ratings and the tire ratings to see where I land on a set of P tires. I do very little off-roading around sharp rocks. Lots of gravel and mud trails around a friends farm, and then the wet boat ramps dictated the 4wd.

KJS Sullivan Enthusiast

KJS Sullivan

Posted
Posted
1 hour ago, 2kwik4u said:

Got a link to it? I can't find them anywhere on amazon as a set. Especially for that price.

Bilstein 5100 Front 0-2.5", Rear 0-1" Lift Shocks Kit for 99-10 Chevy Silverado 1500HD 2500 2500HD 3500 3500HD 2WD / 4WD 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 https://www.amazon.com/dp/B01EXJDLAE/ref=cm_sw_r_other_apa_i_zF7eCb9KAXQ3Q

SquireSCA Enthusiast

SquireSCA

Posted
Posted

The Ranchos seem to have a decent compromise on the compression damning, for soaking up bumps, but as others have noted, it is the rebound damping that is too little, so it rebounds fast and gives that "sproingy" feeling when you go over a speed bump.  When I hit a speed bump at a decent speed it does an ok job of soaking up the hit, but then the shocks, especially the rear, spring back too fast and causes the rear to hop.  Suspension that is properly dialed in will soak up movement in BOTH directions, not just the initial hit and downward stroke.

The upward or rebound stroke is where the stock Rancho shocks seem to really fall short.

KJS Sullivan Enthusiast

KJS Sullivan

Posted
Posted

When I replace my Ranchos I was able to compress two of the shocks with one hand on and they wouldn't even rebound one of them is still compressed in a box for trash and it still has never rebounded yet. So you can imagine the difference in my ride quality with  new bilstein's

Yondu Enthusiast

Yondu

Posted
Posted
27 minutes ago, 2kwik4u said:

Thanks for the info on the shocks. 

 

I can't remember the tire size on the Yukon. They were stock size as best as I can tell. I also moved to a 17in rim from a 16in rim at the same time. That might also have contributed to the increased stiffness, hadn't thought about that until now. I'll have to check the axle ratings and the tire ratings to see where I land on a set of P tires. I do very little off-roading around sharp rocks. Lots of gravel and mud trails around a friends farm, and then the wet boat ramps dictated the 4wd.

I've put tires too wide for the wheel on my GTO before and it made it a bit squirmy on the highway. You could also look for p rated tires that are XL for extra load they'll be a little bit stiffer than a p but not like an LT tire.  

 

What wheels do you have?

2kwik4u Enthusiast

2kwik4u

Posted
Posted
16 minutes ago, Yondu said:

I've put tires too wide for the wheel on my GTO before and it made it a bit squirmy on the highway. You could also look for p rated tires that are XL for extra load they'll be a little bit stiffer than a p but not like an LT tire.  

 

What wheels do you have?

Running the factory 10-spoke 20" wheels that came on it.

 

Here's a pic from the day I bought it. Not a great picture, but the only one I have on my office PC.

2015GMCSierra.jpg

2kwik4u Enthusiast

2kwik4u

Posted
Posted
40 minutes ago, KJS Sullivan said:

When I replace my Ranchos I was able to compress two of the shocks with one hand on and they wouldn't even rebound one of them is still compressed in a box for trash and it still has never rebounded yet. So you can imagine the difference in my ride quality with  new bilstein's

How old were they when you replaced? I'm sitting at ~63.5k miles right now and I've put the last 30k miles on the truck with little change in the ride/handling that I can tell. Wondering if mine were busted when I got it?

KJS Sullivan Enthusiast

KJS Sullivan

Posted
Posted
40 minutes ago, 2kwik4u said:

How old were they when you replaced? I'm sitting at ~63.5k miles right now and I've put the last 30k miles on the truck with little change in the ride/handling that I can tell. Wondering if mine were busted when I got it?

I had 45,000 miles on them, however I noticed something thousands of miles ago where I was just getting his extra clanking noise up front try to research it and everybody said the crossmember at the calipers check all this as soon as the shocks were replaced no more noise, I believe I had two blown out shocks for about 30,000 miles these Rancho things are garbage. When I was reading my window sticker on my truck they made it sound like the Ranchos were such a wonderful thing that they were doing for us LOL, I am running a 3/4 ton however so I know I'm going to have a much rougher ride but these bilstein's make the ride really really good even for a 3/4 ton truck. So replacing them was probably the best thing I could have done and should have done many thousands of miles ago but I only learned about the shocks on this site

2kwik4u Enthusiast

2kwik4u

Posted
Posted
19 hours ago, KJS Sullivan said:

I had 45,000 miles on them, however I noticed something thousands of miles ago where I was just getting his extra clanking noise up front try to research it and everybody said the crossmember at the calipers check all this as soon as the shocks were replaced no more noise, I believe I had two blown out shocks for about 30,000 miles these Rancho things are garbage. When I was reading my window sticker on my truck they made it sound like the Ranchos were such a wonderful thing that they were doing for us LOL, I am running a 3/4 ton however so I know I'm going to have a much rougher ride but these bilstein's make the ride really really good even for a 3/4 ton truck. So replacing them was probably the best thing I could have done and should have done many thousands of miles ago but I only learned about the shocks on this site

Thanks for the info. Looks like the 5100 are the way I'm going to head. Hoping for a year end blowout sale from somewhere to pick them up from.

 

Anyone have a recommended dealer/shop to purchase from?

RHStansbury Enthusiast

RHStansbury

Posted
Posted
8 hours ago, 2kwik4u said:

Thanks for the info. Looks like the 5100 are the way I'm going to head. Hoping for a year end blowout sale from somewhere to pick them up from.

 

Anyone have a recommended dealer/shop to purchase from?

After upgrading to 275/60r20s last week, I'm hoping for a year end blow out on 5100s as well.  Don't seem to need the extra height, but an inch or so certainly wouldn't hurt, right?

 

Also, totally unrelated to this post, but are you the same 2kwik4u from way back on SSF?

2kwik4u Enthusiast

2kwik4u

Posted
Posted
5 minutes ago, RHStansbury said:

After upgrading to 275/60r20s last week, I'm hoping for a year end blow out on 5100s as well.  Don't seem to need the extra height, but an inch or so certainly wouldn't hurt, right?

 

Also, totally unrelated to this post, but are you the same 2kwik4u from way back on SSF?

I feel like there is a "That's what she said" joke in there somewhere.

 

And yeap, same 2kwik4u from SSF. Still post over there once a month or so. Only about 6 of us left that are actually active though :(

JCKustoms Enthusiast

JCKustoms

Posted
Posted
Thanks for the info. Looks like the 5100 are the way I'm going to head. Hoping for a year end blowout sale from somewhere to pick them up from.
 
Anyone have a recommended dealer/shop to purchase from?



FYI - Autopartswarehouse has the front Bilstein for $75 each (today only), and Amazon has the rears for $62 each. Pretty darn good deal!


Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      GM discontinuing interior parts on a 5YO vehicle??

      By Atlas · Posted

      If one can't be found, a good automotive upholstery shop should be able to replace/sew in a new panel where the damage is on the old cover. It might not be the cheapest option..
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Does your dealer charge you for the tire rotation on top of the oil change price ?. I haven't had any service work done at my dealer yet other than when I brought it back soon after owning it to have the front end aligned to correct the steering wheel being off center a bit. Oh they called me at least twice hounding me to bring it in for an oil change and pushing a 300.00 package of oil change and tire rotation and whatever other quick simplistic checks they would do. Only going off of what a friend gets charged for his half ton for the basic oil change and its the same amount of oil as the L8T holds, it was about 150.00. Once one buys a set of tires from most shops these days or so I believe, they will do free tire rotations and some do free tire balancing as well as free tire repairs.    Certainly doing a tire rotation is no five minute job, and definitely not at home but because I run a set of winter tires on their own wheels, I swap them at home and its a one tire at a time deal because of the tire season swap although I jack up the rear and do it and drop it back down and then raise the front and do them and coordinate the tire rotation into that process for both sets of tires. I am using a floor jack though and if I need to raise both ends at once I use a couple sets of jack stands to have all four tires off the ground. I use either an air impact or battery impact and have electric impact as well so no shortage there of easy methods to spin the lug nuts, and then retorquing the lug nuts. None of it goes quick though but my wages are cheap though ... zero. I live an hour out of town, its easier just to do things like that myself than waste a bunch of time in town and having to make an appointment and probably a special trip and sit there at the tire shop waiting for them to get my vehicle in and get it done and not screw something up in the process. 
    • mrbflat
      Clunk when coming to a stop... driveshaft/slip yoke? Mechanic couldn't recreate it

      By mrbflat · Posted

      I do have the 8 speed.  Interestingly enough, after driving my truck for the past 2 days now, I have not had the clunking issue at all!  I am beginning to think it may have been suspension/leaf spring related, and somehow when the shop put my truck on the lift to do their initial inspection, it relieved some built up tension/pressure that was causing my problem.  I swear it felt I was a bull rider on a bucking bull the way the truck would almost rock back and forth slightly before the big thud/clunk when coming to a stop.  I am hoping I got lucky here and it's gone for good.
    • Pryme
      first oil change - 2026 2500HD gas

      By Pryme · Posted

      Bring it to discount tire. They do free rotations even if you didn’t buy your tires there. I didn’t believe it until I tried and they did. You can tip the employee if you would like 
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      Best part of this video is how it resets expectations. Wonderfully done piece. It also made clear a few points I've made from day one. Detergent oils DO NOT KEEP A MOTOR CLEAN at the recommended or longer change intervals. They just get dirty slower than a non-detergent oil and there isn't spits difference between them on this point if they carry the DEXOS license. Great thing about the license that gets missed is it assures CONFORMITY even it that means a low bar.    One thing he did not talk about that I paused on an magnified was the condition of the oil ring separator. Besides a stuck ring a plugged separator and land drain back is huge when it comes control. We see in short order improvement in control IF that is the problem.    Another item I took exception to and he did not make plain was the condition of the timing chest and under valve cover having something to do with indicating piston cleanliness. Schaeffer's Oil makes that same omission in their million mile Ford video. I'm guessing he has never torn down a Red Line HP, AMSOIL SS motor that has been on that diet from the get. What he showed in the video was a good deal of varnish. Something totally absent in Peppers 165K cover off look. I smiled because he did his at the same milage.    He also makes the mistake of assuming oil temperatures in the pan are the temperature all over the motor even though he makes note of the piston being the hottest part of the engine. that baffled me a bit.    I can tell you from personal experience and witnessing teardowns of family motors that even oils of the 1960's would keep them squeaky clean when OCI's were 1500 to 2000 miles without exception. At 3K and above you get what he experienced and the longer you leave it the quicker to gets to the junkyard.    I think his is missing a opportunity not tearing it down again when he's done killing it. Time would be his only cost. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...