Jump to content

What Have You Done With Your T1 Today ?????

Sierra Dan

By Sierra Dan
in Modifications, Wheels & Tires

 Share

Recommended Posts

Comscan Enthusiast

Comscan

Posted
Posted
5 minutes ago, 19chevysilver said:

the fender flares are bushwacker OE style flares. I can measure how far they stick out.

Sent from my SM-N975U using Tapatalk
 

If you would please and thx.

  • Replies 5.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Englshmn
Englshmn

Fabtech Trail Boss / AT4 4" lift Method 305 NV 18x9 -12 4.5" Toyo MT 35x12.5r18

Mbcorry
Mbcorry

Deep matte black vinyl wrap with a gloss black chrome delete!

lt1z
lt1z

First paint correction and seal on the AT4 now that winter is over. This blue looks even better after a clay/polish/seal.

Posted Images

Swiftks Enthusiast

Swiftks

Posted
Posted (edited)

Changed "break-in" oil at 1,500 miles to Amsoil Signature, and added a Fumoto valve while I was at it.

Edited by Swiftks
Chris Callanan Enthusiast

Chris Callanan

Posted
Posted
2 hours ago, Mbcorry said:

Went on a snowy drive!

9E80440D-58A3-4E26-B1F8-3A31A066E1F8.jpeg

Did you stop in the middle of the road to get that photo? Or do you have a drone flying with you for photo-ops?  

  • Like 1
Mbcorry Enthusiast

Mbcorry

Posted
Posted
2 hours ago, Swiftks said:

Changed "break-in" oil at 1,500 miles to Amsoil Signature, and added a Fumoto valve while I was at it.

Total middle of the road stop ?

  • Haha 1
Dunn Senior Enthusiast

Dunn

Posted
Posted
5 hours ago, Swiftks said:

Changed "break-in" oil at 1,500 miles to Amsoil Signature, and added a Fumoto valve while I was at it.

damn, that was quick.....

 

just now gna change it at 5k, 

lapoolboy Senior Enthusiast

lapoolboy

Posted
Posted
38 minutes ago, Dunn said:

damn, that was quick.....

 

just now gna change it at 5k, 

Yep.  I wanted to get all the initial metallics out of the engine from the early break-in process.  I'll do it again at the normal, specified interval.

  • Like 1
Swiftks Enthusiast

Swiftks

Posted
Posted
1 hour ago, Dunn said:

damn, that was quick.....

 

just now gna change it at 5k, 

 

1 hour ago, lapoolboy said:

Yep.  I wanted to get all the initial metallics out of the engine from the early break-in process.  I'll do it again at the normal, specified interval.

Yeah, what he said.  ?

Brandon Watson New Member

Brandon Watson

Posted
Posted (edited)

My New 2019 Silverado Trail Boss Custom 

- 5% tint all around with sun strip 

- chrome tailgate emblems are now factory black emblems 

- Carven Muffler R series with no resonators 
 

Next to do is add a ronin short antenna and leveling kit for the front since it has the factory 2” lift kit . Then get some 20” Factory wheels with 35s 

88995865-2C60-4D66-96AE-8835424082BD.jpeg

Edited by Brandon Watson
  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted
16 hours ago, lapoolboy said:

Yep.  I wanted to get all the initial metallics out of the engine from the early break-in process.  I'll do it again at the normal, specified interval.

I used to do it on my motocross race bikes when they were new, but found out they actually run em a bit b4 they hit salesfloor....my KTM had a magnetic drain plug that would catch the little shavings.....on my truck I am not too worried but yeah not bad idea to do

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...