Jump to content

Drop Shackles

Tano53180
 Share

Recommended Posts

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

mafd2
mafd2

Looks good . Spinning the shim does clear the vib. I like the looks of dropping the rear to level than raising the front.

Zach-91
Zach-91

Got mine in today. Tried to install them on the higher set of holes and found that I still had about 3/4" of rake so I went ahead and went with the lower set. Also flipped around the shims just to be

19trailbossRic
19trailbossRic

Installed those 2”  dropshackles and used the 1.5” hole. Also did airbags to stop the porpoising I was experiencing while pulling a travel trailer at highway speeds over dips. I ride it 1/2” higher th

Posted Images

mafd2 Senior Enthusiast

mafd2

Posted
Posted
Just now, Passivaggressor said:

Put the shackles on mine on the 2" setting. I also experienced some vibration and spun the shims around. 

20190717_114236.jpg

Looks good :thumbs:. Spinning the shim does clear the vib. I like the looks of dropping the rear to level than raising the front.

  • Like 4
  • Thanks 1
Zach-91 Enthusiast

Zach-91

Posted
Posted

Glad to hear that spinning the shim is the fix for everyone. Received mine today and hoping to install tomorrow. 

mafd2 Senior Enthusiast

mafd2

Posted
Posted
23 minutes ago, Zach-91 said:

Glad to hear that spinning the shim is the fix for everyone. Received mine today and hoping to install tomorrow. 

Post pics.

  • Like 1
19trailbossRic Enthusiast

19trailbossRic

Posted
Posted

No vibration on the z71 trailboss so maybe only for 2wd & 4wd (no lift)? She still has a rake for a comfortable ride so just ordered these motofab strut spacers chasing the ilusive level comfortable TrailerBoss. Hopefully the Bag, Drop, chop does the trick. If not will prob go back to the stock shackle with these strut spacers. Will keep you posted! Pic of truck pre-1.5” read dropBC6ED428-C634-4FB2-9F9C-4E3FED227865.thumb.png.8204a78e7607f3fa74875afd463337df.png

A657BC33-7EEC-4C3D-97D6-87FF224C984B.jpeg

Zach-91 Enthusiast

Zach-91

Posted
Posted

Got mine in today. Tried to install them on the higher set of holes and found that I still had about 3/4" of rake so I went ahead and went with the lower set. Also flipped around the shims just to be safe. no vibrations. Just need to adjust the headlights not and all should be good. 

 

Before:

IMG_1346.thumb.jpeg.2357db4626260ab63ccde366b637f100.jpeg

After:

IMG_1347.thumb.jpeg.34fb7feb977967bece08dbfc690e8b37.jpeg

  • Like 5
  • 2 months later...
808 HI Enthusiast

808 HI

Posted
Posted

Sorry for bringing a dead thread back up but sounds like everyone who installed lowering shackles ended up spinning the lower leaf shim. My kit is on the way and wanted to see if I should just spin mine regardless if itll vibrate or not just so I dont have to mess with it again. 

  • 4 months later...
TonyL New Member

TonyL

Posted
Posted

I bought a set of Max Trac shackles from Amazon for my 2019 Z71 and noticed that the bottom was .5 narrower than the factory ones. I decided not to do the install because of this. Has anyone else experienced this issue or would it have not made a difference?

  • 1 month later...
hotrodz37 Senior Enthusiast

hotrodz37

Posted
Posted

For those of you who had the vibrations at 30 mph, was it a vibration like an out of balance tire, or more of a rumble in the cab? 

 

I am experiencing this even though i haven't lowered the rear. I think mine might be pinion angle related as well. It seems as though some trucks came with shims and others didn't.

BlancoSilverado Enthusiast

BlancoSilverado

Posted
Posted
On 1/25/2020 at 7:13 AM, TonyL said:

I bought a set of Max Trac shackles from Amazon for my 2019 Z71 and noticed that the bottom was .5 narrower than the factory ones. I decided not to do the install because of this. Has anyone else experienced this issue or would it have not made a difference?

I dont have any experience with the drop shackles, but and i'm not positive on this, they might of sent you the "old body style" shackles?

moonmaan Enthusiast

moonmaan

Posted
Posted

Just wanted to add some input here because I didn't see anything posted.

 

I have a 2020 custom 2wd crew cab. Had no shake slowing down at low speeds. Installed 2" drop shackles and now have the shake. Truck also came without any shims to rotate. Not sure what to do about the shake.

Zach-91 Enthusiast

Zach-91

Posted
Posted

1st step should be to measure the angles per the link that is above and determine what angle you actually need. 

 

That said, I think the shims that are on my truck are 2 degrees. flipping the shims means we are changing the pinion angle by 4 degrees in the opposite direction because it is double the opposite direction. So if you just want to know what to buy, I'd buy a set of 2 and 4 degree shims and start with the 2 and work my way up to see if 2 is enough. Shims are cheap enough, it's just annoying to pull everything apart a bunch of times which is why it's best to measure.

 

Mine is back at stock height as I have been back and forth with the dealer to get new tires for another vibration. Just got the truck back today so I plan to go back to the drop shackles now. I'll try and get some measurements stock vs dropped with flipped shims since I have to go through the trouble of doing it over again.. 

  • 4 weeks later...
Ryan Valterria Enthusiast

Ryan Valterria

Posted
Posted

I installed the maxtac ”leveling kit” 2” drop shackles on my 2020 Sierra elevation 2wd  crew cab short box. My truck still sits a little high in the back anyone else have this issue?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Coastie05
      Casey from the Texas Hill Country

      By Coastie05 · Posted

      Enjoy the new truck, it’s a beauty. I’m glad you’re keeping the OBS, I love those old trucks. 
    • chris21
      Towing In Loose Gravel

      By chris21 · Posted

      With large equipment or deep mud it is more of a use the higher gear to avoid spinning tires, getting stuck because of spinning tires and doing damage to your machine. The idea is if you run out of torque before you spin tires you can still downshift for more torque. If you are just spinning your tires in the lowest available gear you are stuck and things break.   Automatic transmissions, traction control and electronic transfer cases change the calculation a little as you the driver have less control over each piece. 
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      are there any codes? with lots of rust, perhaps disconnect/clean both sides of the connection/examine cable ends (the wires) for corrosion going into the sheath & replace if necessary/reconnect ALL the power AND ground cables between the battery, engine, frame, cab, fuse box and starter charm.li (website) has a no-start diagnostic procedure you can work through to get it working.
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...