Jump to content

active aero shutters

H1ghlndr
 Share

Recommended Posts

H1ghlndr Enthusiast

H1ghlndr

Posted
Posted

I have a 2020 Sierra HD AT4 3500 SRW Duramax built 1/29/20.  It does not have active aero shutters in front of radiator - looks like it has the holes for each shutter, but no shutter.  Didn't really think about it until watching a YouTube duramax channel with a grille off a 2020 and there were active aero shutters.  I have no codes so I wonder if this was intentional from factory?

 

Do others have (or not) these active aero shutters shutters on their 2020 L5Ps?

 

 

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

newdude
newdude

I had some built after OPs truck  (so Feb build) and some before Jan 2020 and what I found was consistent with the whole plow prep deal.     I also checked dually VINs this morning, no duall

GMC4Zee
GMC4Zee

Just to be clear the reason for the active shutters is to retain engine heat/. BTW I have a 2021 AT4 3500 with plow prep and no shutters.

Crazy Canuck
Crazy Canuck

I am pretty sure that the purpose of the active shutters is to help with aerodynamics.  I am not sure how the GM system works but the 19 f150 I got out of for my 2500 Denali actually would prevent the

Posted Images

unit Enthusiast

unit

Posted
Posted

Diesels don't have the shutters, gasoline engines only.

H1ghlndr Enthusiast

H1ghlndr

Posted
  • Author
Posted

Here is the video I saw.  This is a 2020 duramax...

 

From GM: " In addition to the Silverado HD’s larger dimensions and distinctive trim personalities, 2500 and 3500 SRW models are available with active aero shutters for improved efficiency and a taller, more dominant hood line that asserts the trucks’ strength and character."

 

 

 

cdnSpinalTap Enthusiast

cdnSpinalTap

Posted
Posted

I don't know about the active shutters, but I have seen his videos before.  I could not imagine paying $80k+ (Canadian) for a truck and then ripping it apart like he does...gives me nightmares.

LSPowered65 Enthusiast

LSPowered65

Posted
Posted

Mine has the shutters, 2020 GMC AT4 with a Duramax, you can see them behind the grille. I had to extract a extra push pin fastener from mine, also found one in the hood scoop drain, someone must of felt generous on the assembly line that day. That or my truck is falling apart....

cdh7917 Enthusiast

cdh7917

Posted
Posted
11 hours ago, unit said:

Diesels don't have the shutters, gasoline engines only.

My 2020 AT4HD 2500 Duramax has active shutters.

 

I am wondering if this is a 2500 vs 3500 thing...

unit Enthusiast

unit

Posted
Posted

That's a conundrum  for sure.  I can't imagine why engineers would put shutters in front of that giant charge air cooler and radiator.  As I stated above, my 2020 LTZ 2500HD does not have shutters.  I can see where the shutters would fit into the front grill work for gasoline powered trucks but I didn't think any diesels had them.   It will be interesting to find out what the thinking is on them.

sdelam Enthusiast

sdelam

Posted
Posted (edited)

My 2500 Denali L5P does not have them either. Tied to 5th wheel tow package maybe?

Edited by sdelam
H1ghlndr Enthusiast

H1ghlndr

Posted
  • Author
Posted

I don't have 5th wheel, but snow-plow and towing as part of 3500.  I am wondering if people with no shutters have an option like snow plow prep or something else?  Weird that there are 2500s with / without.  My initial thesis was 2500 and them and 3500s didn't.

 

What options do people have with and without shutters?

Tomato Enthusiast

Tomato

Posted
Posted

I don't see them on my 3500 DRW...L5P Denali with 5th wheel package.

LSPowered65 Enthusiast

LSPowered65

Posted
Posted

I have a 2500 AT4 crew cab, 6’9” bed with the 5th wheel package, not sure about snow plow prep, I would have to check the window sticker.

Tomato Enthusiast

Tomato

Posted
Posted

This is strange...Those that have them - Are they in the top, lower (below bumper) or both sections of the grill?

BlancoSilverado Enthusiast

BlancoSilverado

Posted
Posted

I know for the 1500s, options like trailboss/AT4, snow plow prep, max trailering,.... will play into if you will have shutters. It is probably an option that you have on your truck that does not allow you to have them. 

 

ill go back to my side now. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By asilverblazer · Posted

      Compression test? Weird noises? Fuel trims?
    • asilverblazer
      Wow I'm in a pickle. (Broke down truck) and a story.

      By asilverblazer · Posted

      I suspect at some point in the near future, the hardware will be free and you pay a subscription to access the vehicle - alldata style.
    • parthery
      BAK MX4 EZ-Lift Install and Review

      By parthery · Posted

      I've been eyeing an upgrade to my tonneau cover for a bit now.  Intrigued by the BAK MX4 EZ-Lift with the torsion spring and went for the upgrade.  Thoughts and musings during unpacking, install and a few days of usage.   Once my order went into Realtruck, it took about 4 days to ship.  Unfortunately, FedEx Ground destroyed the box and contents and it was unusable upon receipt.  To Realtruck's credit, one email with pictures and an RMA was sent to me to send the first one back, and another unit was shipped out.  It arrived 3 days later, unscathed.   I opened the box and it looked like every other BAK MX4.   Biggest differences are the rails and retaining clamps, and of course the spring attached to the cover itself.     NOTE - if you are upgrading from a MX4 to the EZ-Lift, you will have to replace the rails.  The EZ-Lift rails have a notch cut in them to allow the new style retaining clamps to fit properly.  The new retaining clamps also have 2 knobs/carriage bolts and there are two tracks underneath the front panel. The strap clips are mildly different (more like the Undercover Flex clamps) in that the screws go in from the underside.  Personally I prefer these over the BAK clamps that use the nutserts that are a nuisance to install.  The remainder of the parts in the box (drain tubes, rail clamps, and bumper pads) are standard issue BAK.     I did not replace my front bed seal at the time because it seemed to be in decent shape.   BAK recommends shims on the GM trucks unless you place the clamps on the flanges about 1/3 of the way in from both the front and rear of the bed.  I shimmed the front and the middle, and initially placed the clamps equidistant.  This also turned out to be a mistake, because when I set the cover in place, the new style retaining clamps wouldn't clear the front clamp.   New style clamp inserted in the track:     And the issue which occurred because the front rail clamp was too far forward:     Once I removed the shim from the front of the bed, and slid the clamp back to the front flange, everything cleared fine.     The cover set on the rails without issue and I installed the strap clamps.  After I completed my adjustments, I pulled the pin to activate the torsion spring.  Mistake #3 on my part.  PULL THE PIN AS THE VERY VERY VERY LAST STEP!  The reason is, once you pull the pin, the torsion spring is activated.  If you have to loosen the front clamps and adjust the cover, the front panel will - by virtue of the spring, refuse to lay down.  The only way to get it to lay down so you can reinstall and tighten the clamps is to fully open the panel against the back of the cab, which will then allow the front panel of the cover to lay down and be tightened.  Not a big deal unless you haven't installed the foam pads yet (typically the last step) because minus the foam pads, you will need to place something between the frame of the cover and the back window so it doesn't get scratched.  The next time I install one I will install the foam pads before I pull the pin and activate the spring.   After using it for a few days:   The spring assist is great.  You literally can open it with one hand.  My shoulders aren't getting any younger and this was part of my motivation to swap out. The second panel latches and unlatches itself as you open and close the cover.  Neat in concept, however it took me a minute to get used to closing the cover and not hearing the "latching" sound that would tell me it was locked in place. The paddle handles are a huge upgrade and I wouldn't be surprised to see them become the standard across the Realtruck line.  They effectively eliminate the concern that a thief could coat hanger the cover open and get to the contents in the bed. I'm not sure why the very front panel on my cover has a different finish from the other 3 panels.  I have a request into Realtruck to find out if mine was not manufactured properly or if it was by design.   All in all I'm pleased.  Same level of protection, looks good, keeps stuff mostly dry (they all leak around the tailgate) and easy to install.
    • KARNUT
      PF63 Oil Filters Going Away?

      By KARNUT · Posted

      Thanks not an answer 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      /facepalm

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...