-
Sign up for FREE! Become a GM-Trucks.com Member Today!
In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience.
-
Similar Content
-
By youn1033
or sale are my set of custom painted, OEM Sierra Denali LED Tail Lights. I had these painted to go on my truck and unfortunately they took so long I had to go a different direction before I got them back.. I have since moved up to a 3/4 diesel and am hoping these can find an owner who will appreciate the time, effort, and $$$ that went into creating them!
These OEM LED Tail Lights are selling for $300 - $500 a piece online, and the cost to have these custom painted Mineral Metallic to match the Denali paint + the lens smoked (lightly, not enough to dim them when lit!) was $700 - looking to get $1,000 including shipping. Can cut a better deal if wanting to pick up in person in the Houston, TX area.
Please reach out for additional pictures, questions, etc. I respond much quicker via text (405) 642-9097
Thanks!
-
By youn1033
For sale are my set of custom painted, OEM Sierra Denali LED Tail Lights. I had these painted to go on my truck and unfortunately they took so long I had to go a different direction before I got them back.. I have since moved up to a 3/4 diesel and am hoping these can find an owner who will appreciate the time, effort, and $$$ that went into creating them!
These OEM LED Tail Lights are selling for $300 - $500 a piece online, and the cost to have these custom painted Mineral Metallic to match the Denali paint + the lens smoked (lightly, not enough to dim them when lit!) was $700 - looking to get $1,000 including shipping. Can cut a better deal if wanting to pick up in person in the Houston, TX area.
Please reach out for additional pictures, questions, etc. I respond much quicker via text (405) 642-9097
Thanks!
-
By hamz
I recently bought a Sierra 1500 Denali because I love this truck but I am now noticing parts are really hard to find, I want to replace or delete my quad steer but have no idea where to start or look. I haven't been able to find anything in hours. Any help?
-
By Derick R
Hello all I'm new to this read forums my entire life when needing help on a issue someone had back in 99. But anyway I have a 2008 Yukon xl 5.3 bought it a few years back quickly realized there was a issue on top of issue. I got screwed and screwed big time. Truck was sold as 168k miles. It was clean nice good looking truck for 4800 bucks. Turns out won't go over 65. We'll we just said screw it and run it for a while until we got our excursion. So now I've been trying to fix it. I need help I've tried refresh at the dealer it sat there for a entire day in a bay with a tech and they couldn't figure it out. So back to the drawing board. Later on tried to trade it in they pulled the carfax trunk our dude swapped the cluster and it was said the last reported mileage was 278k. Well ******. I want to figure out why it will not surpass 65. It has all the gears. Engine has all the power. No limp mode no codes. I have even pulled the cluster and drove it and that didn't change anything. Please help. Thank you. Derick r.
-
By Henry L
2020 Silverado 2500, have taken this truck to two different GM dealers and they cannot find an issue. At the at the 7-pin plug when the manual gain is depressed at 100%, it only puts out 7 volts. Need 12 to lock up brakes. Cannot properly set up my gain when hooked to trailer before towing. Dealership has replaced fuse block brake controller and I had them change out the plug on the bumper. Still the same. At neither dealership have they been able to give me voltage going in the controller and coming out. One even said they can't put a volt meter on it. I believe it's a wire somewhere. But due to my health issues I cannot physically work on my truck. I'm probably going to end up taking it to an auto electrician. Any thoughts!
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
242k
Total Topics1.4m
Total Posts -
Member Statistics
-
Who's Online 40 Members, 0 Anonymous, 998 Guests (See full list)
- SC Dean
- Jv
- bullet225ho
- JimCost2014
- bdallas
- Churchill729
- Rutt
- Steve-2019
- CRApex
- reeseb
- diyer2
- dennismc
- Workdog
- Bleepster
- Grumpy Bear
- J697523
- jerracing1
- CCBIRDDOGMAN
- markyezy
- Salsa De Piña
- mikystyle
- wahoowad
- Jettech1
- XY74
- BrinleyEarnhardt
- Codeman00
- KARNUT
- Pryme
- Kirk Fisher
- eppieguy
- Braulio Boada
- jaxcam02
- 77xbody
- Rock
- Black02Silverado
- Manuel Espino
- Steven-O
- canyon56
- jccshmny
- TwentyEighthNight
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.