Jump to content

Snow tires

rjgvt

By rjgvt
in 2020-2026 Silverado HD & Sierra HD

 Share

Recommended Posts

rjgvt Enthusiast

rjgvt

Posted
Posted (edited)

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm.

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

Edited by rjgvt
  • Like 1
rdonarski Enthusiast

rdonarski

Posted
Posted

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the all-terrain tire option, and they seem to be doing just fine in the snow. 

rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

rdonarski Enthusiast

rdonarski

Posted
Posted
2 hours ago, rjgvt said:

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

As it would turn out, I checked this morning, and my closest Harbor Freight (50 miles away) doesn't stock them. Said I could go to the store, order it and have it shipped to the store for free (2 trips to store). Checked on shipping it - $6.99 - oh hell yes! Wouldn't make one trip for $6.99.

  • Like 1
Ejl923 Enthusiast

Ejl923

Posted
Posted

Been using the HF dolly for years.  Hurt my back 20 yrs ago and this allows me to lift/rotate tires.  The fact that the tire can be spun to line up lugs is the best thing.

  • Like 2
Johnsondavid New Member

Johnsondavid

Posted
Posted (edited)
On 9/12/2024 at 7:31 AM, rjgvt said:

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm. Geometry Dash Scratch

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

I like your idea. Replacing new wheels will help the car operate better and above all it provides safety when moving.

Edited by Johnsondavid
revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
On 9/12/2024 at 7:38 AM, rdonarski said:

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the [b]all-terrain tire option[/b], and they seem to be doing just fine in the snow. 

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Edited by revrnd
  • 2 weeks later...
revrnd Senior Enthusiast

revrnd

Posted
Posted

This comment came to mind yesterday after reading the good & bad comments about Michelin's quality in the other ongoing tire thread in the Silverado HD section.

 

My brother had 2 sets of Michelin LTX M+S tires on his 2016 2500 Sierra HD. He was happy w/ the tire wear on the 1st set, however the 2nd set wore out faster than expected. 

 

His set up and/or usage hadn't changed. Talking to the tire shop, they said that they had seen the less than satisfactory tire wear from Michelin tires.

rdonarski Enthusiast

rdonarski

Posted
Posted
On 9/19/2024 at 9:35 PM, revrnd said:

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Thought I responded to this, but don't see it. Yes, they are the Transforce ATs. They have worked fine for me in the winter, but with this being my 'Till death do us part' truck, I try to minimalize winter use.

revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
2 hours ago, Hoginedgewood said:

Will you have to use a tpms relearn tool every spring and fall?

 

 

Yes. This is the relearn tool that I picked up on Amazon. It works fine w/ the GM sensors. 

 

20241006_205615.thumb.jpg.12a1633d74c89c49440e77b0df3dcb7a.jpg

 

My set of winter rims have aftermarket Schrader(?) sensors & the truck wouldn't recognise them. My local garage was able to 'match' 1 of them to my truck using their Snap-On 'tool' so I'm hoping once they do the rest, my tool will work when I do the swap in the fall.

 

I'll try to remember next month to post.

Edited by revrnd
rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

I have used an Autel TS508 to relearn the TPMS sensors on my previous 1500’s. I used it to program the tire placard pressures to 55psi front/rear on my 2024 AT4 HD. Will use it to relearn the sensors when I take off the KO3’s and put on the snow tires/wheels.

  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted

I spent 2 years in the Rockies in a 1975 Ford Ranger 2WD....it had studded tires on the rear and I stuck 2 manhole lids in the bed....I was actually quite surprised how well the truck did in the snow and ice.....I remember trying to beat the snowplow going up highway 285 on way home at 5 in the morning.......2-4in of dry colorado powder is like driving on asphalt compared to the plow scraping down to the ice.....studded tires are awesome

revrnd Senior Enthusiast

revrnd

Posted
Posted

Studded tires are fine where they're legal.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • BuckWallace
      2027 GMC Sierra: Official Discussion

      By BuckWallace · Posted

      Gotta say the Silverado wins in the exterior looks department, in my opinion.
    • Zane
      2027 GMC Sierra: Official Discussion

      By Zane · Posted

      Not sure about DFM tech but i know there's a stop/start deactivation button. 
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      I could be interested if they axed cylinder deactivation and at least have a button for stop start. I’m sure the HP numbers will be higher. I would want a longer warranty to help build confidence. I’m a less is more guy as I get older. A V-8 work truck model would be my choice. I know a few outfitters for custom additions I prefer. 
    • Zane
      2027 GMC Sierra: Official Discussion

      By Zane · Posted

      It's official. GMC pulled the covers off the next-gen 2027 Sierra 1500, and we got the first official look. Full breakdown here: https://www.gm-trucks.com/next-gen-2027-gmc-sierra-1500-v8-trim-changes/   The quick hits: SLE and SLT are dead. The new core retail trim is just called "Elevation". Two new V8s, a 5.7L and a 6.6L built with high-performance Corvette architecture roots. No horsepower or torque numbers yet. The 2.7 TurboMax finally ditches the old gearbox and gets the 10-speed automatic. AT4X moves to larger standard 35-inch tires with front and rear e-lockers, Multimatic DSSV dampers, and heavy-duty Jounce Control Dampers. Over 60 inches of combined display on Denali Ultimate and AT4X, complete with a motorized articulating center screen and an adaptive passenger screen. Seven simplified trims across the entire model line to clean up ordering confusion.   So let's get into it: New 5.7L and 6.6L gas V8s with custom active exhaust tuning and a Corvette connection. Is this the exact engine lineup half-ton traditionalists have been begging for? Purging the iconic SLE and SLT names after all these years to lean entirely on Elevation as the high-volume core. Bold move, or a mistake? That motorized articulating 16.3-inch screen that slides up to reveal a hidden dashboard vault. Awesome mechanical theater, or does it make you nervous about long-term durability? Physically lowering the headlamps in the front fascia to improve road courtesy and stop blinding oncoming traffic. Smart real-world engineering, or does it hurt the truck's aggressive stance? What trim are you putting your name down for on day one? Drop your first impressions below.  
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      My overnight hospital stay turned into five.  I developed a post operative fever and an erratic  heart rate.  A blood clot in the lungs was the culprit.  This is apparently a common post surgical complication and easily remedied.   I was the youngest in a four bed ward and a Doctor with a Geriatric specialization was in charge of my care.  All of the nurses were good and some were outstanding at dealing with old people.  It was very evident that my age triggered a different level of care!  My advice to any senior going for a hospital stay is to have a trusted family member advocate visible.  If not, you will still be well cared for, but you may discover that your voice  isn't as strong as it once was! 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...