Jump to content

Bilstein shocks thread

yanzhixiang

By yanzhixiang
in Modifications & Accessories

 Share

Recommended Posts

Snowcamo Senior Enthusiast

Snowcamo

Posted
Posted

Well I have a strut failure. I forget how long its been, but i posted here when I installed them. Passenger front is bouncing like the black factories used to. Drivers still functions as designed. Spoke with 4 wheel parts and they will have someone ride and verify and inspect. I'll pull it and have it swapped. Will update. They say it'll be covered under bilstein warranty.

  • 3 weeks later...
  • Replies 2.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bwilloby46
bwilloby46

I put the bilstein 5100s on the rear of my 14 High Country with a new 2" block a few weeks ago. Ride is unbelievable compared to stock. Liked it so much I got the adjustable 5100s for my front, remove

schloppy
schloppy

Hello, I'm not new to the forum but I just joined and figured I'd contribute to the community.   2016 Silverado 1500 "Z71" removed rancho's and swapped with Bilstein 5100's all around. So after d

Jullian is not my name
Jullian is not my name

I just got done with installing my 6112's on my 2014 GMC Sierra Crew Cab.  Reading some install guides on here really helped, along with printing some Chilton Repair guide torque specs that I got from

Posted Images

18LT Enthusiast

18LT

Posted
Posted (edited)

I’m a little late to the party but after dealing with a slow leak on my truck I’m ready for new tires and a leveling kit but wanted to ask a couple tires. My truck is a 18 LT. I don’t go offroading I just want a little more clearance and bigger tire for northern MI winters. so I don’t need anything too hd which after reading seems like the 5100 will give me that along with a better ride. I know the fronts can go up to around 1.8”. Do the backs raise it at all? Or what do you guys use for the rear? Also where have you guys bought yours from I didn’t really see, the, on the bilstein website. Any input is appreciated. Also I read through a lot of the posts on here just looking for a little more info. 
 

infound this which looks like the front adjustable plus a strut spacer and 1” rear lift. But I imagine it doesn’t ride as good as without the strut spacer.

https://socalsupertrucks.com/bilstein-leveling-2-5-lift-5100-shocks-2014-2018-silverado-sierra-1500/

 

and these from bilsteinlifts.com is that the actual bilstein website? It says the rear shocks are 0-1”. Is rear adjustable also or what brings the rear up. 
https://www.bilsteinlifts.com/shop/chevy-gmc/silverado-1500/14-17-chevygmc-silverado-1500sierra-1500-4wd-bilstein-5100-0-1-8-front-0-1-rear-lift-shocks/

 Sorry for all the questions Im sure they have been answered but I can’t find them. Just want to make sure I buy the right part

Edited by 18LT
ThundahBeagle Enthusiast

ThundahBeagle

Posted
Posted

Hi 18LT,

 

The fronts are adjustable, the rears are not. Having said that, the rears a made so that the can withstand it if you did raise the rear about an extra inch. Typically, raising the rear of your truck would be don with blocks at the rear axle. A 1 inch block is really two inches. You remove the original one inch block that came with the truck and replace it with the 2 incher, giving you 1 inch of lift in the rear. I left my rear stock.

 

Regarding the fronts: only use the built in adjustments. Do not then also add a spacer to the fronts. I went with the highest setting and I think it looks good. Be aware that when you do that, sometimes the front might seem higher than the back. It isnt, but it might look like that to the eye. I added a leer cap to mine, that's almost a couple hundred pounds. If I then load the bed up with tools and camping gear, or some other heavy thing, it can sink down a bit and look a little foot-high. If you have the ability to, you may want to experiment putting it on the setting one down from the top, depending on what you like, and what you typically carry or tow.

 

I got mine from a dealer in the Jeep forums because I also have an old Grand Cherokee and I bought stuff for that through him. He will give you the best deal he can

 

His name is Nick, but he goes by Kolak.

Reach him at [email protected]

Tell him that the guy from Boston, who knows where he got "Kolak" from, sent you

  • Thanks 1
Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted
1 hour ago, ThundahBeagle said:

 Having said that, the rears a made so that the can withstand it if you did raise the rear about an extra inch.

Exercise. Extended length minus compressed length is stroke length. 50-60% of that number is a shocks designed static stance dimension. IF you do run this exercise on a stock shock you will find that you have 9 inches of stroke but measurement on the truck unloaded will reveal the shock is 3-1/2 inches ABOVE center! Why? Because the rear shock on a pickup is fitted to be in the 50-60% of stroke range when it is at it's maximum carry load. This also means the when the truck is empty there is nearly zero rebound stroke left. 

 

They may allow an extra inch of ride height but will still be nearly topped out at rest and that extra length won't move the compression bumper any further away. 

  • Thanks 1
ThundahBeagle Enthusiast

ThundahBeagle

Posted
Posted

Hi Grumpy Bear

 

I have no reason to doubt your math and engineering on that. You do mention stock shocks, however. The Bilstein is a replacement to the stock shock, so I'm guessing it's designed with more stroke? They state it is designed for 0 to 1 inch of lift, so I can only presume that they have accounted for all of that?

 

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted
4 minutes ago, ThundahBeagle said:

Hi Grumpy Bear

 

I have no reason to doubt your math and engineering on that. You do mention stock shocks, however. The Bilstein is a replacement to the stock shock, so I'm guessing it's designed with more stroke? They state it is designed for 0 to 1 inch of lift, so I can only presume that they have accounted for all of that?

 

I encourage you to take or get the measurements. If you take them at their face value that would mean a shock with 5" or so more stroke. Is it? Is it really 5 inches longer that stock? Or is it a shock with 1" more stroke? 

 

I use Kings on the rear of mine and they make the same claim but the truth is that shock is exactly the same length at the stock unit with the exact same measured stroke. 21" OAL. 

 

Just say' n. Don't take my word, their word or anyone else. The measurements and math are to simple to get yourself. 

 

For a guy who hauls allot of tows allot at or near maximums this matter not but if you run empty allot you can gain some rebound distance removing the factory block at minimum. It won't put you at center but it is an improvement you will notice on drop off's like pot holes.  

  • 2 weeks later...
stevejones Enthusiast

stevejones

Posted
Posted

I went with the 5100's on the 3rd notch, then replaced the factory Michelins with 265/70 Generals - so up a very slight 1/2" with the tires.  Nothing radical, but I like the look & road manners with this combo.

Trouble_shooting Enthusiast

Trouble_shooting

Posted
Posted
On 11/11/2020 at 10:18 AM, Grumpy Bear said:

Exercise. Extended length minus compressed length is stroke length. 50-60% of that number is a shocks designed static stance dimension. IF you do run this exercise on a stock shock you will find that you have 9 inches of stroke but measurement on the truck unloaded will reveal the shock is 3-1/2 inches ABOVE center! Why? Because the rear shock on a pickup is fitted to be in the 50-60% of stroke range when it is at it's maximum carry load. This also means the when the truck is empty there is nearly zero rebound stroke left. 

 

They may allow an extra inch of ride height but will still be nearly topped out at rest and that extra length won't move the compression bumper any further away. 

I went through a similar exercise of math when outfitting my rear axle.  I ended up using Monroe Load adjusting shock part#: 58640 vs the Chevy spec. part#: 58648

  The #58640 are actually spec. to a 2006 Dodge Ram.  Dimensions though, allowed darn near 2” additional up travel.  While only losing  about a 1/4” down travel.  The GM is 14mm eye compared to Dodge 9/16”
 

Bonus is, it lifted the rear about a 1” and firmed up the rear end.  I now have installed 2 other sets on fellow K2XX owners and so far so good.

 

  • Like 2
Snowcamo Senior Enthusiast

Snowcamo

Posted
Posted
I went through a similar exercise of math when outfitting my rear axle.  I ended up using Monroe Load adjusting shock part#: 58640 vs the Chevy spec. part#: 58648
  The #58640 are actually spec. to a 2006 Dodge Ram.  Dimensions though, allowed darn near 2” additional up travel.  While only losing  about a 1/4” down travel.  The GM is 14mm eye compared to Dodge 9/16”
 
Bonus is, it lifted the rear about a 1” and firmed up the rear end.  I now have installed 2 other sets on fellow K2XX owners and so far so good.
 
Interesting. Does this make the back more smooth or just add more travel. How did you deal with mounting bolts? Thanks.

Sent from my LM-G820 using Tapatalk

  • Like 1
Trouble_shooting Enthusiast

Trouble_shooting

Posted
Posted
14 minutes ago, Snowcamo said:

Interesting. Does this make the back more smooth or just add more travel. How did you deal with mounting bolts? Thanks.

Sent from my LM-G820 using Tapatalk
 

The ride didn’t change much, a little less squat when loaded.  One of the sets that I installed were on my wife’s truck.  She didn’t notice a difference, in ride quality.  
 

As for bolts, I used the factory bolts tighten to factory spec.  No noticeable play or unusual sounds.

  • Thanks 1
  • 2 weeks later...
CbrownGT Enthusiast

CbrownGT

Posted
Posted

Been trying to comb through this and utilize search function but..anyone with a 16-18 with stamped steel UCA’s running the 5100’s up front at settings 2, 3, or 4 and a stock 20 inch rim with a 33 inch tire (275/60/20 specifically) and have zero or minimal rubbing on UCA?  Having a hard time finding answers on this 

jimbrown1 Enthusiast

jimbrown1

Posted
Posted
3 hours ago, CbrownGT said:

Been trying to comb through this and utilize search function but..anyone with a 16-18 with stamped steel UCA’s running the 5100’s up front at settings 2, 3, or 4 and a stock 20 inch rim with a 33 inch tire (275/60/20 specifically) and have zero or minimal rubbing on UCA?  Having a hard time finding answers on this 

I have this setup but I left the front shocks at stock setting and used a Rugged Off-road spacer.  This is on a 2018 Sierra Crew Cab.  No rubbing with the 275/60/20 BFG tires.  

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      Injector update

      By diyer2 · Posted

    • Atlas
      The Peckish Synapse

      By Atlas · Posted

      I'm tangentially aware of what Harley used to be, back in my riding days, although I was into Italian sport bikes. Ducati seems to have gone the other way; still very expensive, but they've made a large subset of their bikes a lot more reliable and accessible, and they've diversified their lineup to include other riding sports too. IMO, a good example of where greed and growth might have also been beneficial to the consumer.   Although GM is charging a relative premium for its most popular pickups, I find that there are some excellent value propositions in its lineup as well.   The Colorado still strikes me as the most attractive midsize on the market, and also the most reasonably priced given capability and features. There's a part of me that wishes I would have bought one instead of my Silverado.   The Equinox ...I must be getting old. The ICE equinox is a great design IMO. Probably because it reminds me visually of an actual SUV aka an S Blazer. Underneath it's nothing even remotely close, but it LOOKS good. It's got all the modern features plus some at a very reasonable price. If I had to run out and buy myself a daily commuter to do everything except tow, an Equinox would be on my list.   It does bug me that mid-tier 1500's reach into the 50-60k range, and Tahoes and Burbs are even more expensive. Less than 10 years ago, dealers were sitting on rows of Tahoe LS and LT's for low 40's. You could even still find Tahoes with a front bench, still!
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      Big oil is raking in billions from the Iran war. Can it avoid Trump’s fury?   Remember I said Big Oil is 'Vertically Integrated"?   Even as they no longer own the majority of the "Pump" they still own the "Well". Crude price upward pressure does not translate into that same pressure on production. Pumping cost remain unaffected and the gap is pure profit. Even after subtraction of a minor, comparatively, lower amount from supposed, but not always, realized refining volume. Consumers hate war, Big Oil, not so much.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      We live in a world where the average person expects more. People say wages and our needs are farther apart. My first new home had 3 bedrooms and one bedroom. My first car and truck had what would be considered a stripped or work vehicle. In my neighborhood back then there were more homes like that and cars too. Middle managers and second home buyers worked their way up to the fancy houses and cars. Car loans were 3 years. GM had different models of cars for different income levels. The cars were pretty much the same size if you wanted a big vehicle. The nameplate designated the opulence. Chevy, Pontiac, Buick, Oldsmobile and Cadillac.  To be fair some of the cost is government mandated. We can’t blame them for giving us what people will pay for. Careful advertising steering people towards more profitable SUVs and trucks. As I learned recently a minivan is a cheaper more efficient form of transportation. Certainly easier to live with. Somebody realized the profit margin wasn’t as big and gave it a soccer mom label. So it lost its coolness. They’re making it the masses are buying it. You hit your hand with a hammer you can’t blame the hammer.
    • Aussie2500HD
      Electrical /Immobilizer Data- Battery Voltage (V) Test malfunction

      By Aussie2500HD · Posted

      Hi All, I’m In need of advice regarding a scan result on my 2023 Silverado HD.  The Sensor Supply voltage relay states ON But…. the following 3 tests show Malfunction. Sensor supply voltage relay control circuit HIGH voltage Test status- Malfunction Sensor supply voltage relay control circuit LOW voltage Test status- Malfunction Sensor supply voltage relay control circuit OPEN test status - Malfunction. No DTC codes are stored. No DIC Lights. Remote Key Fob has been giving a few issues, namely Vehicle will not respond to an Open/Lock command from the key fob. New batteries installed to FOB made no difference, plus on one occasion recently the vehicle unlocked using the Fob, the vehicle started normally via the push button, then a random warning came up on the DIC stating the Remote Key was not found, all this while the key was located next to the central cup holders. Does anyone have any input or advice regarding this scenario? TIA 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...