What Have You Done With Your T1 Today ?????

[SILVER SLED]

Ran a 13.61 at the racetrack today and swapped out the chrome/red Z71 emblems for black.  

[New2GM4]

On 8/12/2020 at 10:36 PM, Htown T1 said:

Found a mint condition dual exhaust bumper. I installed it and installed the powder coated tips I had already. Simple swap, it looks much better now. I took it to the exhaust shop today to reroute the exhaust. 

How did you get the matte black tailgate? Is it dipped or a cover? 

[Htown T1]

1 hour ago, New2GM4 said:

On 8/12/2020 at 9:36 PM, Htown T1 said:

Found a mint condition dual exhaust bumper. I installed it and installed the powder coated tips I had already. Simple swap, it looks much better now. I took it to the exhaust shop today to reroute the exhaust. 

How did you get the matte black tailgate? Is it dipped or a cover? 

It’s a cover from Air Designs. It’s goes on with double sided tape. 

[Julio13]

Installed rough country hooks and Baja designs fog lights




Sent from my iPhone using Tapatalk

[New2GM4]

2 hours ago, Htown T1 said:

It’s a cover from Air Designs. It’s goes on with double sided tape. 

Did you just transfer your lettering or did it come with it? If it didn’t, did you paint etc? Thank you 

[mjonesjr84]

Swapped the OEM rear under seat storage compartment (small) for the Du-Ha compartment. The Du-Ha one is the only one I've found that mounts the same way as the OEM one with the jack and tool set holding it in. I did have to trim the floor liner at the jack location so it would sit flat on the floor.

[Htown T1]

3 hours ago, New2GM4 said:

Did you just transfer your lettering or did it come with it? If it didn’t, did you paint etc? Thank you 

Yes, I transferred the letters over. You have to remove the “silverado” letters on the lower left and any letters you may have on the lower right to put this cover on. I had ordered OEM gloss black “silverado” letters from eBay and spaced them out in that blank area. So the cover does come blank but I decided to put the letters on there and leave the way it comes (Matte black) instead of painting it. I’m sure you can go a cheaper route and just plastidip your current letters. 

[jimmyboy8301]

Went for a drive today





Sent from my iPhone using Tapatalk

[GTPprix]

I dont know why... but I put those "GMC" logo puddle lamps in... Actually really dig them then again I'm also easily Amused

[lapoolboy]

1 minute ago, GTPprix said:

I dont know why... but I put those "GMC" logo puddle lamps in... Actually really dig them then again I'm also easily Amused

Yep!  I got the Chevy ones!  I stare at them and smile every time I unlock the doors! 

[GTPprix]

Yep!  I got the Chevy ones!  I stare at them and smile every time I unlock the doors!  [emoji16]

So far I’m doing the same LOL!!

[NorthernAT4]

Removed some badging and added the carbon pro AT4. Black gmc front and rear. Little jet seal coat before winter and now waiting on the bilstein 5100 front and 5160 rese rears to show up with cognito control arms. 

[mjonesjr84]

Replaced the OEM antenna with a shorty. So far I can't tell any signal loss (I mostly listen to SiriusXM anyway). The OEM antenna hit my garage door when pulling in and out. I'm not really a fan of the shorty antenna, not sure why GM couldn't have put the antenna in the XM antenna like my Equinox and my previous 2016 Colorado was.

[Transient]

Ordered OEM black exhaust cutouts for the rear bumper that come on the midnight edition Silverados. Then went to the carwash to find out my truck is too tall to use that carwash. With the light bar installed I estimate I need a minimum of 7'5" of clearance. This particular carwash was only 7'2".

 

Truck is headed into the dealership Monday for its first routine service. Ironically, as the oil change notification came up, so did a CEL. That was Thursday. Had OnStar email me the DTC code readout. P25A2. I do suffer from the squeaking belt at start up. I wonder if this is related. Also notice the belt squeaking a bit more over bumpy roads at 35mph while I was driving with my windows open. Once I cleared the bumps the belt stopped squeaking. I wonder if the squeaking is associated with the alternator pulley.

 

Sent from my SM-N960U using Tapatalk

 

 

 

 

[TA^Guy]

Did some badge overlays and removed the “Sierra” from the tailgate.