Jump to content

Recommended Posts

Posted (edited)
14 hours ago, JohnCasey said:

Class action suits just enrich lawyers. I don’t want enrichment I want a non leaking truck. Shouldn’t be that hard to produce for the $50,330.85 I spent. 

I agree. I just want to confidence that my truck is going to be able to stop, that my window won’t leak, that if these issues arise THEY CAN BE FIXED. I never had to think about any of these issues with my Taco. NOT to bash my AT4, I absolutely love it. I only have the 5.3 and love the power, love how it tows, the mpg etc...

Edited by mistaare
Grammer
Posted
On 1/10/2020 at 11:09 AM, OhioSpartan said:

They installed new cabin pressure valves as the originals were not seated correctly.

Did yours pop out completely like mine did?  (Video here: )

How long did you have to wait for yours to come in?  While my glass came in remarkably quick, I am still waiting for the vents to come in!

Posted

Update: Just got my truck back from the dealer. Looks like they performed the repair per the TSB.  No shotty sealant job on mine.

15AD3129-6554-42E1-8829-38C04103467C.jpeg

  • Like 1
Posted
26 minutes ago, SeTex said:

Update: Just got my truck back from the dealer. Looks like they performed the repair per the TSB.  No shotty sealant job on mine.

15AD3129-6554-42E1-8829-38C04103467C.jpeg

They may have done it neatly which is good. But caulking over a cracked window frame with seam sealer is shoddy in my book, no matter what...

  • Like 2
Posted
8 hours ago, n8huntsman said:

Did yours pop out completely like mine did?  (Video here: )

How long did you have to wait for yours to come in?  While my glass came in remarkably quick, I am still waiting for the vents to come in!

Dealer ordered mine on Dec 20th and they arrived Dec 30th. They told me the delay was because they had go back to the parys supplier in Lansing.  I don’t think mine popped out, just rattled so bad the window rattled

Posted

Got mine back tonight. Window was replaced with the same make and model my 2020 came with from the factory. I was very upfront with my dealer about the bad experience I had before with the glass company and my truck getting scratched and greasy fingerprints. It was obvious they were stressed this had to be done perfect. My truck was detailed inside and it looked like it came off the showroom floor. They washed the outside more on that in a minute.

There was a good sized chip in my paint on the rear rocker from them getting in and out with boots on. Not a big deal should touch up with a drop of paint. That was about it I thought. Then I noticed the middle seatbelt was twisted. Not a big deal. Just need to undo the bolt and untwist it.

Then I ran to the store and it was warm out (42 deg, yeah that's warm here). So I cracked the sunroof and opened the rear slider. Something seemed off. I hit the button for the rear window again and nothing. They must have forgotten to hook up the rear window. So we went through all that and nobody thought hey should I check if this window works before I put it back together? I mean really? So now I have to drop it back off. Hopefully it just isn't connected and will be quick fix. God if they have to install another window...

My truck only has 2000 miles so with early snow, and hunting season I didn't really give the truck a good wash yet or pay much attention because bit was covered in mud. But since my dealer washed it I looked at it in the dark with a flashlight. Granted it is black but what the heck, my truck looks like it was sand blasted. I hand washed it with some soap and it doesn't really come off.. some of it did it I picked at it but not really. The front quarter panels, and bumper have it all over but just a few speckles on the rest of the truck. Any idea? I don't think it's water spots. Almost looks like white paint overspray?35c19ff94fa83ccf105629298ee22345.jpg30141b39a6af25b459e14e8da064b638.jpga875bcb617090e0af70ca146591e6ea4.jpg

Sent from my Pixel 4 using Tapatalk

Posted

I can’t believe this issue is still going on. I was one of the first. I was absolutely livid that my $70K 2019 Sierra Denali began leaking at the rear window. My heart goes out to all who have been affected by this defect and the myriad other issues. There’s nothing worse than having a brand new vehicle with problems. I’ll list mine in order:

1. Rear window leak

2. Infotainment glitches

     a. Infotainment Climate control intermittent malfunction

     b. Can’t find Navigation SD card

     c. Blue screen for reverse cam

3. Anti collision braking not working        
4. Brake life indicator counting down too quickly

5. Passenger side mirror not folding in completely

6. Intermittent loss of side view camera image

7.  Slight shaking at highway speeds

8. Driver side front window auto up stops half way and goes back down (really annoying)

9. Passive door locks sometimes don’t work

10. Horn chirp is muted (Sounds soft and weak) when remote arming security system

 

i think that’s all ?

 

Oh!...and now none of the driver assist features work after the latest front camera software recall (N192275630) performed by the dealership today. No lane assist, no pedestrian braking, no forward emergency braking.


I love the way this truck looks and how it rides (except for the occasional shaking at highway speed - which is intermittent), but overall disappointed in GM’s quality control. Most of these systems are not new technology so this isn’t first model year issues, with the exception of the rear window leak. 

Posted
10 minutes ago, ShamrockShooter said:

Got mine back tonight. Window was replaced with the same make and model my 2020 came with from the factory. I was very upfront with my dealer about the bad experience I had before with the glass company and my truck getting scratched and greasy fingerprints. It was obvious they were stressed this had to be done perfect. My truck was detailed inside and it looked like it came off the showroom floor. They washed the outside more on that in a minute.

There was a good sized chip in my paint on the rear rocker from them getting in and out with boots on. Not a big deal should touch up with a drop of paint. That was about it I thought. Then I noticed the middle seatbelt was twisted. Not a big deal. Just need to undo the bolt and untwist it.

Then I ran to the store and it was warm out (42 deg, yeah that's warm here). So I cracked the sunroof and opened the rear slider. Something seemed off. I hit the button for the rear window again and nothing. They must have forgotten to hook up the rear window. So we went through all that and nobody thought hey should I check if this window works before I put it back together? I mean really? So now I have to drop it back off. Hopefully it just isn't connected and will be quick fix. God if they have to install another window...

My truck only has 2000 miles so with early snow, and hunting season I didn't really give the truck a good wash yet or pay much attention because bit was covered in mud. But since my dealer washed it I looked at it in the dark with a flashlight. Granted it is black but what the heck, my truck looks like it was sand blasted. I hand washed it with some soap and it doesn't really come off.. some of it did it I picked at it but not really. The front quarter panels, and bumper have it all over but just a few speckles on the rest of the truck. Any idea? I don't think it's water spots. Almost looks like white paint overspray?35c19ff94fa83ccf105629298ee22345.jpg30141b39a6af25b459e14e8da064b638.jpga875bcb617090e0af70ca146591e6ea4.jpg

Sent from my Pixel 4 using Tapatalk
 

Looks like overspray to me. Never seen water spots that small and they generally come off with a wash.
 

Clay bar should take it off but you’ll likely need a good polishing after. Already see some faint “love marks” in the paint.

Posted
Looks like overspray to me. Never seen water spots that small and they generally come off with a wash.
 
Clay bar should take it off but you’ll likely need a good polishing after. Already see some faint “love marks” in the paint.
Yeah those little scratches were there when I bought it with 100 miles. What would that overspray be from? It's white and my truck is black. It is very dense on quarter panels but oddly just a speck or two on hood, like it happened when hood was up or not on vehicle

Sent from my Pixel 4 using Tapatalk

Posted
31 minutes ago, ShamrockShooter said:

Yeah those little scratches were there when I bought it with 100 miles. What would that overspray be from? It's white and my truck is black. It is very dense on quarter panels but oddly just a speck or two on hood, like it happened when hood was up or not on vehicle

Sent from my Pixel 4 using Tapatalk
 

Could have been something leaking from a truck and the vehicle in front of you kicked it up, kinda like how wet roads leave a film on the sides of your vehicle but not the hood or roof so much. I agree with OnTheReel, need to clay the truck before the sun cures whatever that is. From your description, sounds like paint. Get a bucket of soapy water (heavy soap) and clay bar (I like to use synthetic clay). Griot’s and Mother’s both make synthetic clay and available at local auto parts store. Do a 12” x 12” section at a time keeping the panel and the clay very soapy. Rinse and repeat until that section is free of the overspray. It usually doesn’t take that much elbow grease, let the clay do the work...don’t press too hard and use up and down, not circular motion. Once finished, wash the entire truck and apply a good coat of wax/polymer sealant. This not only protects the paint, but will make it much easier to remove bugs, tar and future overspray. Good luck. Zaino Brothers website has some great clay bar techniques and advice if you care to check it out. No, I’m not soliciting business, just some good techniques I found on the site a while back.

Posted
Could have been something leaking from a truck and the vehicle in front of you kicked it up, kinda like how wet roads leave a film on the sides of your vehicle but not the hood or roof so much. I agree with OnTheReel, need to clay the truck before the sun cures whatever that is. From your description, sounds like paint. Get a bucket of soapy water (heavy soap) and clay bar (I like to use synthetic clay). Griot’s and Mother’s both make synthetic clay and available at local auto parts store. Do a 12” x 12” section at a time keeping the panel and the clay very soapy. Rinse and repeat until that section is free of the overspray. It usually doesn’t take that much elbow grease, let the clay do the work...don’t press too hard and use up and down, not circular motion. Once finished, wash the entire truck and apply a good coat of wax/polymer sealant. This not only protects the paint, but will make it much easier to remove bugs, tar and future overspray. Good luck. Zaino Brothers website has some great clay bar techniques and advice if you care to check it out. No, I’m not soliciting business, just some good techniques I found on the site a while back.
Thanks for all the great tips. Unfortunately the high forecast for Friday here is 19 degrees. It going to have to wait a while

Sent from my Pixel 4 using Tapatalk

Posted
I can’t believe this issue is still going on. I was one of the first. I was absolutely livid that my $70K 2019 Sierra Denali began leaking at the rear window. My heart goes out to all who have been affected by this defect and the myriad other issues. There’s nothing worse than having a brand new vehicle with problems. I’ll list mine in order:
1. Rear window leak
2. Infotainment glitches
     a. Infotainment Climate control intermittent malfunction
     b. Can’t find Navigation SD card
     c. Blue screen for reverse cam
3. Anti collision braking not working        
4. Brake life indicator counting down too quickly
5. Passenger side mirror not folding in completely
6. Intermittent loss of side view camera image
7.  Slight shaking at highway speeds
8. Driver side front window auto up stops half way and goes back down (really annoying)
9. Passive door locks sometimes don’t work
10. Horn chirp is muted (Sounds soft and weak) when remote arming security system
 
i think that’s all [emoji848]
 
Oh!...and now none of the driver assist features work after the latest front camera software recall (N192275630) performed by the dealership today. No lane assist, no pedestrian braking, no forward emergency braking.

I love the way this truck looks and how it rides (except for the occasional shaking at highway speed - which is intermittent), but overall disappointed in GM’s quality control. Most of these systems are not new technology so this isn’t first model year issues, with the exception of the rear window leak. 


Intermittent highway vibration is usually from a couple tires slightly out of balance rotating enough to finally line up just right and combine forces. I always road force balance tires when I get to about 5,000 miles. Very rarely do they break in and stay balanced perfectly. Tires are great now in terms of comfort and mileage, but they can be a bitch to balance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Very true.   However.  GM did give those trucks with the single speed case Terrain Mode.  Terrain Mode mimics 4LO minus the gear reduction and torque capability.  It uses the ABS/braking system to perform the operation.  It also gives these one pedal driving (sort of) when in Terrain Mode via the active brake during throttle lift.     Does it have its limitations over a true 2 speed case?  Sure.  But it works.         
    • Of course actually engaging four wheel drive is step one or even daring to use a ramp like that with a two wheel drive and getting into a mess because of it. As to 4 low, these last few years if its a GM half ton it may not even have low range. A lot of the newer pickups have a lot lower first gear in an automatic transmission then they once did as it was common at one time for a gas engine truck or even the older diesels to just sit there and bog the engine due to the torque converter stall point and not enough torque was generated on reasonable traction to even spin a tire or get out of its own way up a steep grade and 4 low HAD to be used to get enough power to four tires to get them turning. These days traction control systems may hinder a vehicle in a situation like that although that means a tire or tires are spinning so in some ways the traction control can reduce wild spinning and anyone can correct me on that but I think some vehicles cut traction control off in low range ?.    By the sounds of it and you may have the proper equipment but if your responsible for helping vehicles out if they are not able to get out under their own power, I would say to be using a nylon tow rope or have one available so that one is able to give a bit of a run to help sling shot them some initial momentum as most tow straps are made out of polypropylene and impart way too much shock load if used to jerk a stuck vehicle into motion but are totally fine to use if going more from almost a dead pull with the tow vehicle and they are a lot less expensive to replace if damaged. That and some soft shackles to hook onto closed loop tow hooks on the truck your pulling as well as you having the proper shackle insert in your truck so there are no bad accidents with metal clevises joining things together or chain on the end of a tow rope or tow balls being hooked onto etc flying and causing damage or worse if it lets go. Its always a challenge pulling people because some are clueless and will over run the tow rope or strap and drive over it or that risk of ramming into the back of the tow vehicle so usually a few instructions are needed to clue in the driver of the stuck truck. Yeah ... have fun out there 😉
    • In their own words:    https://blog.amsoil.com/how-engine-sludge-forms-and-how-to-prevent-it-2/   [Quote] Synthetic Oil Helps Prevent Sludge Fortunately, sludge and varnish deposits are something that can be controlled. Using thermally stable synthetic base oils reduces the rate of degradation (oxidation).   Antioxidant additives further help reduce the rate of degradation. One of the most widely used is zinc dithiophosphate. Not only is it an excellent oxidation inhibitor, but it is also an outstanding anti-wear additive.   High-Quality Additives Fight Sludge Fortunately, it is possible to address many of the issues that occur after the initial oxidation stage. Additives, such as detergents and dispersants, help promote the suspension of contaminants within the oil and keep them from agglomerating.   Detergents, which are also alkaline in nature, assist in neutralizing acids generated in the sludge-building process. Antioxidant, dispersant and detergent additives are consumed during use.   To achieve maximum life expectancy, use a motor oil with high concentrations of antioxidant, dispersant and detergent additives.  [End Quote]   So quality base oil and then the last sentence above. TBN and ZDP levels matter. The one thing not covered was sufficient viscosity. Sad.     And yet we now have since API SN lower amount of them all with the only real change being a slight up tick in base oil selection. Along with lower concentrations of everything that makes oil work and lower and lower viscosity there is still an insistence on longer OCI's.    How low does the peanut butter and jelly level have to get before we say it's just white bread folded?    The new smoke and mirror treatment is the 'additives are INVISIBLE' to UOA testing with a health dose of TRUST ME.    I'm not picking on AMSOIL. This is coming from all of them. Every last one of them that abandon the low wear model in favor of the high mpg/EPA compliance model. 
    • First off use it in the way you’re more comfortable. In working in off road situations most of my life I used 4WD low range very little. In most cases when equipped I used auto 4WD. If I wanted maximum control going up and down very steep terrain  I used low range. Especially if I was driving a diesel. Same with very rutted terrain. In very muddy or snowy conditions I wanted momentum so high range worked well for that. With gravel ramps with limited traction I would try high range first. I would want smooth even increasing speed if I was fighting traction. Low range could give you too much to the wheels breaking traction trying to move. 
    • Having owned 4wd vehicle since the 1970s I find there are varying opinions on how to use 4wd, every owner is an expert in their minds.  IMO, 4LO is the appropriate gear and what I would use,  You have to feather the gas to avoid spinning tires and the lower the gear the better chance.  But like I said you will find those that think their method is best.  I live near a boat launch.  Yesterday there was a new Ford Maverick pulling out a pontoon boat almost 2x its size, they had no problems and they don't have a LO range.   True story. One winter day not long ago I was coming out of small town post office and there was a F150 4wd parked in front and was stuck foot deep snow ruts. I knew the lady so I asked her to put it in 4wd (wondering why in the middle of a 2-day snow storm she wasn't).  Her reply surprised me, "my husband" (the expert) told me not use that because it uses too much gas. She finally got unstuck spinning in 2wd which likely used more gas than not.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...