Jump to content

Recommended Posts

Posted (edited)

Ready for some travelling soon. Forest RIver Salem Cruise Lite 17'. Added the GM trailer camera system too.

 

A few camera views here.....

 

Default view from side mirrors

https://www.youtube.com/watch?v=zhMS11KDJQU

 

Transparent Trailer Cam view

https://www.youtube.com/watch?v=eiTgTIGAqFw

 

 

1206201125_resized.jpg

Edited by richmz
  • Like 3
Posted
2 hours ago, richmz said:

Ready for some travelling soon. Forest RIver Salem Cruise Lite 17'. Added the GM trailer camera system too.

 

A few camera views here.....

 

Default view from side mirrors

https://www.youtube.com/watch?v=zhMS11KDJQU

 

Transparent Trailer Cam view

https://www.youtube.com/watch?v=eiTgTIGAqFw

 

 

1206201125_resized.jpg


Nice! What engine/tranny do you have? How does it pull? How is the squat?

Posted (edited)
17 hours ago, Jrodpic said:


Nice! What engine/tranny do you have? How does it pull? How is the squat?

It's the AT4... 6.2L gas with 10 speed. Pulls like a dream. Trailer weighs only around 4,000 lbs plus the water tank was full, so maybe 4400 or so, but when we go off fully loaded with stuff it'll likely be around 5k.  No Gray or Black water in it when I test drove my setup after they delivered it.

 

The trailer rating for the truck is 9,200 lbs. I have a load leveling hitch setup and set it so the truck is within about  1/4" or so from the unloaded level position. No squatting. IIRC when I first connected up it only squatted about 1 1/2" at the rear bumper which surprised me. After I set the torsion bars to raise it it came right into it and leveled off nicely.

 

I had a '06 Silverado(5.3L, 4 Spd auto) for 15 years and towed my 23' Continental enclosed car trailer(cars were about 3,500 lbs, total about 7,000 lbs) and it always struggled and I always had to drive in D3. The '06 was rated about 7,500 so I was using all of it.

 

Night and day between the 2. That's why I upgraded to the 6.2L, knowing I'd be better off, but didn't want to go the HD 2500 route or get into a diesel. 

 

Rich

PS the last 3 photos..... I had 23 bags of bark mulch loaded in the bed when I took those photos. I was amazed how it held up. When I drove back from HD all loaded up it felt great. Amazing truck.

 

1206201125_Burst01_resized.jpg

1204201134_resized.jpg

1024201610_Burst01_resized.jpg

1202201605_Burst01_resized.jpg

1202201605_resized.jpg

1202201605a_resized.jpg

Edited by richmz
typos
  • Thanks 1
Posted
1 hour ago, richmz said:

It's the AT4... 6'2L gas with 10 speed. Pulls like a dream. Trailer weighs only around 4,000 lbs plus the water tank was full, so maybe 4400 or so, but when we go off fully loaded with stuff it'll likely be around 5k.  No Gray or Black water in it when I test drove my setup after they delivered it.

 

The trailer rating for the truck is 9,200 lbs. I have a load leveling hitch setup and set it so the truck is within about  1/4" or so from the unloaded level position. No squatting. IIRC when I first connected up it only squatted about 1 1/2" at the rear bumper which surprised me. After I set the torsion bars to raise it it came right into it and leveled off nicely.

 

I had a '06 Silverado(5.3L, 4 Spd auto) for 15 years and towed my 23' Continental enclosed car trailer(cars were about 3,500 lbs, total about 7,000 lbs) and it always struggled and I always had to drive in D3. The '06 was rated about 7,500 so I was using all of it.

 

Night and day between the 2. That's why I upgraded to the 6.2L, knowing I'd be better off, but didn't want to go the HD 2500 route or get into a diesel. 

 

Rich

PS the last 3 photos..... I had 23 bags of bark mulch loaded in the bed when I took those photos. I was amazed how it held up. When I drove back from HD all loaded up it felt great. Amazing truck.

 

1206201125_Burst01_resized.jpg

1204201134_resized.jpg

1024201610_Burst01_resized.jpg

1202201605_Burst01_resized.jpg

1202201605_resized.jpg

1202201605a_resized.jpg

Thanks for the info. The older 5.3 is a good chunk less powerful than the new ones. And the 4 speed is probably what killed you. Looking at a trailer that is around the same dry weight. Didn’t know the 6.2 was that much heavier. My 5.3 weighs about 220 pounds less so the max is 9400 and 940 tongue weight. Or maybe the GMCs are heavier???

Posted
12 hours ago, Jrodpic said:

Thanks for the info. The older 5.3 is a good chunk less powerful than the new ones. And the 4 speed is probably what killed you. Looking at a trailer that is around the same dry weight. Didn’t know the 6.2 was that much heavier. My 5.3 weighs about 220 pounds less so the max is 9400 and 940 tongue weight. Or maybe the GMCs are heavier???

Yes the old iron block 5.3L Vortec was ok and a better choice over the base(4.6L iirc?) at the time. I've read about the present aluminum block Ecotec3 5.3L version being more powerful.

 

My '06 was 4WD so it likely dropped the tow capacity down a bit due to added weight . It had the HD Trailer Tow pkg. Not sure if that actually adds weight or not, or is a wash for the tow capacity.

 

I'd imagine the same with the AT4  being 4WD that they drop it down a bit from a 6.2L base rig in 2WD. The 6.2 is likely a bit heavier than the 5.3 but probably not too much. Is yours 4WD? If so then maybe as you said the GMC flavor may be a few hundred pounds heavier and they have to drop the tow rating to compensate.

 

Rich

 

Posted
17 hours ago, richmz said:

It's the AT4... 6.2L gas with 10 speed. Pulls like a dream. Trailer weighs only around 4,000 lbs plus the water tank was full, so maybe 4400 or so, but when we go off fully loaded with stuff it'll likely be around 5k.  No Gray or Black water in it when I test drove my setup after they delivered it.

 

The trailer rating for the truck is 9,200 lbs. I have a load leveling hitch setup and set it so the truck is within about  1/4" or so from the unloaded level position. No squatting. IIRC when I first connected up it only squatted about 1 1/2" at the rear bumper which surprised me. After I set the torsion bars to raise it it came right into it and leveled off nicely.

 

I had a '06 Silverado(5.3L, 4 Spd auto) for 15 years and towed my 23' Continental enclosed car trailer(cars were about 3,500 lbs, total about 7,000 lbs) and it always struggled and I always had to drive in D3. The '06 was rated about 7,500 so I was using all of it.

 

Night and day between the 2. That's why I upgraded to the 6.2L, knowing I'd be better off, but didn't want to go the HD 2500 route or get into a diesel. 

 

Rich

PS the last 3 photos..... I had 23 bags of bark mulch loaded in the bed when I took those photos. I was amazed how it held up. When I drove back from HD all loaded up it felt great. Amazing truck.

 

1206201125_Burst01_resized.jpg

1204201134_resized.jpg

1024201610_Burst01_resized.jpg

1202201605_Burst01_resized.jpg

1202201605_resized.jpg

1202201605a_resized.jpg

That's a good looking truck and a nice set-up.

 

I am somewhat surprised at the difference in the load & towing capacity when compared to my 2020 Silverado, Z71/RST, CC, 5.3L.

 

When comparing the capacity stickers, my 5.3L, Z71/RST, CC, is 375 lbs lighter (5179 lbs), has a max payload that is 475 lbs more (1921 lbs), a conventional towing weight/tongue weight rating that is 400/40 lbs more (9600/960 lbs), and a goose-neck trailer/tongue weight that is 1900/285 lbs more (9500/1425 lbs).

 

I guess I am most surprised by the difference in curb weight and max payload. The max payload difference is around 25%. That said, it's hard to argue against the power of the 6.2L in a pick-up truck.

 

Looks like you have a comfortably paired combo of truck and travel trailer. Enjoy the travel.

 

JMHO

No expertise implied or expressed.

Posted
7 hours ago, richmz said:

Yes the old iron block 5.3L Vortec was ok and a better choice over the base(4.6L iirc?) at the time. I've read about the present aluminum block Ecotec3 5.3L version being more powerful.

 

My '06 was 4WD so it likely dropped the tow capacity down a bit due to added weight . It had the HD Trailer Tow pkg. Not sure if that actually adds weight or not, or is a wash for the tow capacity.

 

I'd imagine the same with the AT4  being 4WD that they drop it down a bit from a 6.2L base rig in 2WD. The 6.2 is likely a bit heavier than the 5.3 but probably not too much. Is yours 4WD? If so then maybe as you said the GMC flavor may be a few hundred pounds heavier and they have to drop the tow rating to compensate.

 

Rich

 

5.3 10 speed Trailboss

Posted
3 hours ago, Coles5515 said:

What size trailer is that? Motor/trans?

Its the Cougar 27RESWE so its about a 29' trailer in total. The truck had the 6.2l with 10 speed. I say had, because after crunching the numbers, with truck, canopy, passengers, dogs and trailer tongue weight I was about 500-600lbs over the payload of the truck as it did not have the HD package. Long story. We took it from our home in Oregon to Flathead Lake in Montana and the truck had no issue towing the setup, I am just a worry wort, and didn't want to give the insurance CO any reason to deny a claim should anything happen. Stepped up to a 2020 2500 Denali. So that setup was do able, just not for me.

Posted
3 hours ago, Coles5515 said:

What size trailer is that? Motor/trans?

Oh also the 6.8-7.2 MPG sucked towing. I expect the Duramax to do much better...

Posted

Hey guys. Does anyone have any real world examples of a 1/2ton truck towing another 1/2 Ton truck?

I have a 2019 trail boss LT 5.3L v8. Want to see if I can tow my 2011 silverado extended cab also with 5.3.

I ran some numbers and I am coming up with a technical “yea” I could do it. But I’m planning on a 6 hour drive over the grapevine in CA (big elevation changes). I used an online calculator and had to input a couple variables like - guessed that the trailer would have GVWR of 10,000lb (pj trailer buggy hauler model) and that the trailers “cargo weight” is simply the curb weight of the 2011 truck being towed which I put in as 5500 lbs.

Here is the trailer sticker from my truck.

I’m debating renting a 3/4 ton truck from enterprise instead.

f1b31a39560ef2b0bcdf9eec8c2db9fb.jpg
a1bacdbe4c8fc128c0d1de01eb4ae2b2.jpg


Sent from my iPhone using Tapatalk

Posted

Your truck can do it in my opinion, but you are close to it's limits and with inclines and declines I'd feel much better if I were in a 3/4 ton with better brakes, I'm not concerned about suspension, brakes are the big thing in my opinion.

 

 

Just my .02

  • Like 1
Posted
On 2/4/2021 at 10:02 PM, Londart2020 said:

Oh also the 6.8-7.2 MPG sucked towing. I expect the Duramax to do much better...

 

I am surprised by how poor your mileage was towing.  I have seen as low as 4.5 mpg pushing hard with big load going up steep hill, but overall tow cycles are in the 8.2 to 9.6 range.  Can you tell us how much your trailer weighs, how  tall, type of towing terrain,- over mountains - head wind and your typical towing speed - other factors that may have impacted that. 

 

I only ask as I had a 2019 AT4 - 6.2 10 speed - towed about 10k miles with that and now have a 2020 AT4 (6.2 10 speed with tow mirrors) and have towed about 4,500 miles with it.  The 2019 on a typical trip got 8.2-8.8 mpg - the 2020 on my last two trips (450 miles +/-- round trip) got 9.2 and 9.6 mpg respectively.   All towing a 24' Inteck race car trailer (30' overall length) loaded to about 8,500 lbs. 

 

My typical tow loop is from Orange County to Sand Dunes (Gordon's Well - south end of Glamis) and back - which includes up and over a 4,200 foot grade over and back (about 50 miles of the trip is up and down in the mountains), there is aways wind in the mountains and often a head wind the last 5 miles out of the desert before you head up the mountain.

 

649394741_2020AT4w-trailers.thumb.jpg.2703ef3e644cd0af3c16d84403f6d586.jpg

Posted
6 hours ago, Supercup said:

 

I am surprised by how poor your mileage was towing.  I have seen as low as 4.5 mpg pushing hard with big load going up steep hill, but overall tow cycles are in the 8.2 to 9.6 range.  Can you tell us how much your trailer weighs, how  tall, type of towing terrain,- over mountains - head wind and your typical towing speed - other factors that may have impacted that. 

 

I only ask as I had a 2019 AT4 - 6.2 10 speed - towed about 10k miles with that and now have a 2020 AT4 (6.2 10 speed with tow mirrors) and have towed about 4,500 miles with it.  The 2019 on a typical trip got 8.2-8.8 mpg - the 2020 on my last two trips (450 miles +/-- round trip) got 9.2 and 9.6 mpg respectively.   All towing a 24' Inteck race car trailer (30' overall length) loaded to about 8,500 lbs. 

 

My typical tow loop is from Orange County to Sand Dunes (Gordon's Well - south end of Glamis) and back - which includes up and over a 4,200 foot grade over and back (about 50 miles of the trip is up and down in the mountains), there is aways wind in the mountains and often a head wind the last 5 miles out of the desert before you head up the mountain.

 

649394741_2020AT4w-trailers.thumb.jpg.2703ef3e644cd0af3c16d84403f6d586.jpg

It's a 29' TT it's about 10'6" tall that weights in at about 7700lbs + passengers+150lb of dogs. It was from Oregon to Montana so there was a bit of mountain towing. Don't recall too much wind. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • The part # is 84520447, mine does not have the cooled seats but I'm willing to possibly change the cover and foam if needed.   I tried that site and a few others,  added to cart and then paid. About an hout later I received a refund stating it has been discontinued. 
    • Thought I would add to what Bruce answered, not only do the HD models use the torsion bar system, there are I believe 5 different torsion bar spring ratings that are all physically interchangeable with all the HD trucks going from a two wheel drive 2500 all the way up to the duramax or a gas engine truck with a snow plow prep package front end weight capacity that use the maximum sized torsion bar. It starts from a 4400 lb rated set in 400 lb increments up to 6000 lb. If one wants to fine tune the ride for a certain truck application they can swap out the torsion bars. 
    • First off pay close attention to what Newdude pasted as he is a GM tech !.    I have a couple of questions which might cross off some questions others on this forum would be wondering about as well. So when was the engine oil changed prior to this trip, was it almost brand new oil or did it already have a fair bit of use on it before you started the trip.   Did you check the oil level on flat ground and was it at the full mark just before leaving on this trip which I gather from google map is about 700 miles or so. Why I ask and this is not the first time in history that has happened, that either a dealer or some other shop changed the oil on the vehicle and the vehicle left the shop and the owner ( you ) assumed the engine oil was full but in reality the person who changed the oil simply did not put enough oil into the engine .. it happens !. Also that a shop put the wrong viscosity oil in and an engine was not happy with that thinner viscosity and oil got past the rings at a higher rate than the proper viscosity. Not to mention if there was any leaking out of a drain plug or the filter gasket etc. 
    • You could, although in the end it really doesn't make much difference what comes out in exact terms since it comes down to putting enough back in so that there is enough volume so that something flows back out once the trans is up to temp for the check procedure. I presume your putting a pan on that has a drain plug but its probably the same pan mold/size as at least a while back no extra volume pan was made for the gas truck version due to the exhaust cross over pipe issue. All I can say as per volume I put back in and this was based on changing out the filter as some is trapped in it that does not come out until its removed because of the way its made inside and my truck had sat over night with the trans having been hot when shut down and dripping internally before I pulled the pan. I went off of what the trans shop suggested as a minimum volume he found worked which was 9 1/2 quarts and I had enough flow out of the stand pipe that I knew I was right on the money once it slowed to a dribble and never wasted hardly any oil but it would be totally fine to throw in a full 10 quarts too. I guess personally I wouldn't ruin a perfectly good pan by drilling a hole in it, not with the cost of replacement pans up here or the dorman one anyway with the drain was 500.00 when I priced one out a while back, totally stupid.    I might not have said before but this trans oil type really expands with heat and I think its been said on this forum and the trans shop said the same so I wanted to try and hit the lower temp of the range vs at the top or go shooting above it as that would allow more oil to flow out which wouldn't be ideal. 
    • Since I am going to be replacing the pan, I am just going to drill a hole in the original to drain it so I will be able to catch the fluid easier and measure how much I took out.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...