Jump to content

Recommended Posts

Posted (edited)

I think its retarded to not have a handle to drop the gate.. My pops truck has been to the dealer twice for the tailgate now. All because the button isn't working...

Edited by 20Bowtie14
  • 2 months later...
Posted

I think everyone knows these are gravity drop and everything has to be perfect to drop.  I had a GM tri fold soft cover that locked it up tighter than a tick.  So I took the rear seal of the topper  out (it's directional) and reversed it.  Applied a small amount of silicone oil and as long as I'm level or up hill it releases every time. Any parking downhill and gravity does its thing. 

  • 4 weeks later...
Posted

I have the exact same issue. When I pull on the tailgate with even a little pressure (guessing about 5lbs with 1 hand) and press the release button with the other, I hear the clicking, but nothing happens. I noticed it when I had some doors for the house in the bed and I had to unload the bed one door at a time lifting over the sides because it wouldn't open.

 

I took it to the dealer today, they checked for recalls and service bulletins, found nothing. The dealer said they tried it on another truck on the lot and it did the same thing. Now I'm wondering if I should take it in again.

 

How "normal" is this issue? Members that aren't having a problem, have you tried pulling on the tailgate while you press the release button?

 

 

Posted

This is honestly the most ridiculous problem to have on a pickup! Sorry for the OP's problem, but there isnt even a key hole or handle to open it manually! My fathers had this same issue and he had to have the dealer reprogram something. He couldn't get his tools out of the bed to do a job we had because he has a hard tonneau cover!

Posted
8 hours ago, 20Bowtie14 said:

This is honestly the most ridiculous problem to have on a pickup! Sorry for the OP's problem, but there isnt even a key hole or handle to open it manually! My fathers had this same issue and he had to have the dealer reprogram something. He couldn't get his tools out of the bed to do a job we had because he has a hard tonneau cover!

 

Agreed! If there was a "manual tailgate" as an option I would have sought it out. Seems like a very gimmicky feature.

Do you know what your dad had done, and has it worked since they did whatever they did? I'm looking for a solution.

Posted

My 2019 trail boss tailgate does the same thing.  Most of the time the first button push just makes a click sound but doesn’t drop.  Then if I press it again the tailgate usually drops.  Mine has been that way since day one as well.  I’d much rather have a handle since this mechanism doesn’t seem to be all that reliable.  

  • 5 years later...
Posted

I am having this issue with my tailgate.  It won’t release more than one out of about 50 tries.  I have taken it apart and I see that the linkage system and electric actuator are a joke.  With the cover off the side of the tailgate, I can release it every time, quite easily, if I grab the linkages and release them manually.  Clearly there is an adjustment issue, or the switch actuator just doesn’t move far enough.  The linkage hooks into plastic bushings and and has about a half inch of free play.  If the play was not there, it would open fine…there seems to be a very obvious and bad design flaw in this electric release system.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • If anyone lands here looking for an update - the problem wasnt with the hose, the clamp, etc... I purchased a metal Thermostat housing that just must not of been made to spec. It just wouldn't plug up the hose.. Went back to a plastic cheap housing - leak fixed. Some plumbers tape carefully placed in tandem with a clamp likely would've gotten the job done.   Best,
    • For anyone following, this is what I have deduced from this forum - and my very specific niche case. Please do let me know if you see me going in the wrong direction here. For context, I have a 16 sierra 1500 w/t. Has TC and Cargo light switches. Removed the switch to find the X1 and X2 of the S48A connection populated with wires (x1 10-14, and x2 1-5).   Took photos of the X61A-X5 to find the wires from S48A-X1 land here at their respective pins (10, 11, 17, 23 on the X5). Was hopeful that this means my X51A fuse box has the appropriate pins... No cigar. So now I will be routing wires from the rear of the X61A-X1 to the engine bay and to their respective negative relay triggers. Please see to the diagram. If any has insight as to where the S48A-X2 pins 4 and 5 land that would be awesome.   Note: please disregard fuse sizes. Main fuse will like be 25A, all mini bus fuses will likely be 10-15A   Cheers
    • 287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...