Jump to content

2019+ leveled trucks

jimmyboy8301
 Share

Recommended Posts

  • Replies 537
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

BlackLS
BlackLS

1.5" Motofab leveling kit. I plan to run this spacer until BDS comes out with a 4" lift for the Trail Boss/AT4  

Bluerado23
Bluerado23

2” ready lift front only 315/70/17 ko2 17x9.5 wheels

asalinasz39
asalinasz39

Just a 1.5” in the front with motofab lower strut spacer. Still have 1” rake and stock duratracs 32.3” tall. Sent from my iPhone using Tapatalk

Posted Images

Satinsteelmetallica Enthusiast

Satinsteelmetallica

Posted
Posted
On 10/6/2019 at 7:47 PM, hramales said:

How the ride quality on that set up, I’m looking at doing something similar on my 2wd RST. Also do the tires stick out any on the sides? Any rubbing issues?.. Sorry for the bombardment of questions but I’m new to the truck scene. Thanks 

It's all good.  No issues.  Rides like factory.  No rubbing.  Tires do not stick out. 

20190917_140036.jpg

scdaren Enthusiast

scdaren

Posted
Posted
On 10/7/2019 at 7:48 AM, tannerm24 said:

Motofab 1.5” level. 
35/11.50r20 Ridge Grapplers. 
 

No offset. No trimming. No rub. 
 

Make sure to measure your rake. I had the 1.5” level installed and it’s perfectly level. 2” would have been too much. 

8CB99441-05D5-48E0-ABEC-EBB61D3D6B65.jpeg

Thanks for posting, good to know. That’s just very slightly smaller than a 295/65r20, so that should fit well too. I have 2” both front and back, so kept the rake. 

elleshoe Enthusiast

elleshoe

Posted
Posted
On 10/8/2019 at 8:31 PM, Satinsteelmetallica said:

It's all good.  No issues.  Rides like factory.  No rubbing.  Tires do not stick out. 

20190917_140036.jpg

Can you post a pic like this but from the rear so I can see tire width from that angle please? 

Frank DeVoe Enthusiast

Frank DeVoe

Posted
Posted

Learning a lot in this thread, looks like a 2 inch level on my ltz 2wd will give plenty of room to put 33's on the stock 18's. Quick question though, is there one leveling kit that's better than the other when comparing a top spacer or bottom spacer? Thanks. 

Satinsteelmetallica Enthusiast

Satinsteelmetallica

Posted
Posted

You can fit 33's without a leveling kit with plenty of room.  The stock wheels that came on my truck were 275 60 20 which is a 33.  With the leveling kit you can go with a wider 33 or taller than 33. I have the 2 inch Rough Country level which is a bottom spacer with 295 60 20 Nitto Terra Grappler G2 and it rides nice.  I don't know if a top or bottom spacer is supposed to be better but so far I like the bottom spacer on my truck.

  • Like 1
  • Thanks 1
Ezekiel2517 Enthusiast

Ezekiel2517

Posted
Posted

I called several level kit companies.  Some claim top vs bottom doesnt matter.  Others say top is better as it is more robust I'd u did actually go offroad 

JHP Enthusiast

JHP

Posted
Posted

Sorry to ask what may be for some of you the DUMBEST question of all time, but . . . what are all of you meaning when you say the term "rake"?   

 

????

 

Just trying to learn the vocabulary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined

  • Who's Online   5 Members, 0 Anonymous, 1,383 Guests (See full list)

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Declaring victory would upset the demons that possess this Blazer, so I won't. But I did make progress today--after it put up a fight. Always a fight.   I had the day off so I spent the morning cleaning up the shop and I thought I'd get ahead of things by filling the cooling system in prep for the final part I needed to arrive: the driver's side knock sensor. Glug, glug, glug....and then the unmistakable sound of liquid hitting the shop floor. It induces the same chagrin when the sonar and targeting laser temporarily malfunction during a late night bladder evacuation over the toilet with the bathroom light off. D'OH!!! That made a mess...   Oh, hey, that knock sensor I removed? It threads into a wet port. Who knew?! Learn something new every day. Put a pin in that chore, I'll fill it the rest of the way later.   The knock sensor arrived at about 1pm. I threaded it in, connected the wire, filled up the coolant, checked for leaks, and... drumroll.... fingers crossed for a perfect start, excellent timing, model fuel trims, and ...no squeaks... Here goes.....   No, it didn't start. At all. I cranked it a few times and it wasn't sounding good. Furthermore, I heard leaking again. Jesus H Tapdancing Christ, stop leaking all over the dang floor. This time I had accidentally overfilled the coolant reservoir and the churn of the water pump via cranking caused a bit to burp out. Ok, just, breathe... Put the flamethrower down. Dang thing wouldn't burn anyway, leaks too much...   Did you know the rotation of a round crank sensor in a round hole, matters? I do now. Took me about half hour to retrace steps and realize what I had done. Then it started right up.   No squeaks. The squeak was the old balancer.   Once it entered closed loop, fuel trims are dead on, hovering right around zero at idle. No more -30%. I'll credit the injector rebuild on that one.   Timing? I think there's an OBD 1.5 translation error with my Actron scanner. It's anywhere from -20 to -30 at idle, sometimes as high as -40 cruising. Sorry, the engine just isn't running that smoothly at -40 degrees ignition advance. It's just not. It's smooth all through the rev range and has decent power. I'm going to have to trust the seat of my pants on this one.   The new exhaust is very quiet. The old catalytic converter? Not melted, but definitely not healthy. Rains glitter when you turn it on its end...all the precious metal is flaking out. Once the new exhaust system burned in/smoked off a bit, the engine's exhaust smell is normal again. Not that I'd recommend going around huffing car exhaust, but, you know what I mean?   One problem to correct. The new exhaust has the opposite problem of the old spliced up exhaust. It wants to hit the floor where the old one wanted to rest on the cross member. Happy medium, please? Still noodling on that one, need to look at how I can adjust some hangers.   I don't know what's next. On one hand I want to run away from this thing as far and as fast as I can -- there have been a lot of NOT fun moments. On the other, now that it kinda drives nice, maybe drive it around for a little bit?   Shhh... it's not currently dripping oil all over the floor. I can see just a little wet at the bottom of the timing cover where it meets the oil pan seal. It's not dripping multiple drops with every ignition cycle, in fact, after some driving this evening it has yet to even form a drop that could drip off yet. But the weekend is young... I fully expect this could turn into Exxon Valdez by Sunday. Because this Blazer hates me. LOL.      
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      About that:   Once upon a time in a land far far away lived a car company that was shy about taking your money and wanted to be sure that they gave you more that you asked for so that you'd come back. No really, not a fairytale. 😱   But after the field got thinned out enough to limit the competition it seemed good enough to give you only what you asked for. Fair enough I say but in such a market you have to give something the others are not or they go to the one who does. Gimmicks or glitz. Oh, fins and chrome. Yea, shinny crow like cars. Yum.    Field narrows a bit more and 'brand loyalty' becomes a thing and the minute it does they start thinking to themselves, "Could we make more money if we gave them less than they expect and they will hang in there for brand and comfort with the known?" They gave it a try and da*n, it worked!!    Well, what if we teach them, groom them into believing that less is "Normal" and cut some more corners. Will that work? Oh heck yea!    🤔 I wonder, can we give then WAY less than they expect and make them mad enough to spit nails and STILL get them to pay up? Sure, if we get everyone else to do the same so that the choice is less or nothing at all. How would be do that? Platform sharing.  What a concept, right?  Steal like there is no tomorrow and it's legal too!    Truth is no one is going to give up driving, not for very long. The Gen Z crowd is fine with it and will be as long as someone not Gen Z will haul them around. At some point we all die.    Economic voting only works if you cast a NO vote now and again and enough of them to get dumb and dumber to wise up. Well, that's how I was taught anyway. And it should have worked. Would have worked. But the Bail out!!   Look, you have another choice if  you take that bag off your head. If the dumb it down to some predetermined expectation of how John Q Public will use it the, that is under design it to failure they you use it to a lower stress mode. D'ho!    A 1950 Royal Enfield Bullet 500 will go anywhere a Suzuki Hayabusa will and for just as long. But you will have to treat it for what it is and not for what you wish it was. 
    • Vu1can
      Bridgestone vs Goodyear tires?

      By Vu1can · Posted

      Maybe I was just too unlucky, but I had nothing but bad luck with Bridgestones. Out of 3 sets, they all started losing a lot of air when they got down to about 1/2 tread life, and at that point also wet traction suffered more than it should have. Also, the only tire I ever had in my 60 years of driving that had a side wall blow out was a Bridgestone.   I'm currently running Goodyear Wrangler Workhorse AT and am very happy with them.   
    • davester
      Broke Down on the Mountain

      By davester · Posted

      maybe when the trip is over, check all the other joints in the front end, like all the ball joints, tie rods, pitman & idler arms, etc...
    • Carlos Eduardo Silva
      adding 360 surround view, UVI (Trailer Camera) package to UVS (Surround/invisible Trailer) Upgrade 2020 Silverado RST

      By Carlos Eduardo Silva · Posted

      Thks, and actually it was my bad, because here in this post there is someone showing the correct wire position as well. My bad... But thank you a lot with the help as well. I was able to find and buy a 10 channel VPM that came from a sister silverado of mine. The same year, same mode, same trim, same everything. 2022 Silverado 1500 LTD LTZ (pre-refresh). I also found to buy just the bottom mirror part that has the cameras, so way cheap than the full mirror. + a used front camera. I did test everything together, cameras, cables and the VPM.... everything worked EXCEPT my original Bed camera and the backup grid lines. I think the reason is because now I need to do the VPM reprogram. I sent a msg White Automotive & Media Service to confirm that it is the problem and that they can do it service for me case.   Once I get it 100% done I will post here result....

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...