Jump to content

Recommended Posts

Posted

^^ nice Legend (and pull vehicle)! I'm guessing you fit the RZR in it?

Yes I'm really happy to have an all aluminum unit now after seeing how brutally rusty my old steel open trailer frame has gotten over the years (even paint it every second year). My tandem 7x19 has torsion axles so no leaf springs to rust either. 

  • Like 1
Posted

Found some windows on eBay that are narrow enough to fit between the framing. Busted out the jigsaw and sheets of insulation foam. It’s now my better-than-a-tent camp trailer.

 

The Honda is much taller than the rzr and rubs the rear opening. 76” tall just fits.

 

e8954ce281fd42d5cdb06b16d6d46235.jpg

 

  • Like 1
  • 5 months later...
Posted
On 1/15/2019 at 6:03 PM, cperk said:

Pic last fall, I’ve since upgrade to a 2500 diesel.cca3a5b75404b34090311ad2fb6cd256.jpg318d9a272960238c3dd36b8db94065b9.jpg
Just have to get a shell and the kayak racks back on!!!


Sent from my iPhone using Tapatalk

Holy cow that's a long travel trailer. Do you just camp in pull-through spots? There's no way that beast would fit anywhere go. I barely get my lifted 18' jayco into where we camp without ripping the jacks or decals off.

Posted

Upgraded the truck to a 2020 AT4 2500 HD Duramax.

8da97c5d6210f3340b755d6af045b6b3.jpg


Sent from my iPhone using Tapatalk

  • Like 1
  • 2 months later...
Posted

New to us 2017 308bhts. 9a052fbdb5f665683d5fcb337ab57ac1.jpgc7d40e75d806f20e6bfb6c23d375b0b2.jpg

Sent from my SM-G975U1 using Tapatalk

  • Like 2
  • 3 weeks later...
Posted

Awesome trailer and absolutely impressive setup. Now I'm inspired to upgrade my current setup. I wanted to turn my truck into an off-road recovery vehicle before. I'm currently looking at fifth wheel hitch at 4wheelonline and see if it will suffice for towing. 

  • 4 weeks later...
  • 4 weeks later...
Posted

20200726_191412.thumb.jpg.8eb52428cdeb80409106e227fe7a42dd.jpg

Towed a new toy home. Really gotta get a new receiver to adjust for the lowered suspension. And I'm fairly certain the Uhual trailer weighed more than the bike. 

Posted

Rented a 6x10 cargo trailer to move some stuff this week.

I loaded the trailer with lots of tongue weight, in addition to having lots of weight in the truck bed. It leveled out the truck pretty good. I hauled it 5h down the highway. Got 14.1 l/100km loaded, with a tailwind. On the way back, empty, I got 16.5 l/100km into a very strong headwind.

ad20f7e6e59060a6640985a98e68ee23.jpeg


Sent from my iPhone using Tapatalk

Posted

2020 Rockwood 2509S. Our first trip a few weeks ago, Headed to Cumberland Mountain State Park, Tennessee 90bfc2d96cbec0c3f0b2b3abbca9f44e.jpg

Sent from my SM-N960U using Tapatalk

  • Like 1
  • 5 weeks later...
Posted
Heading to the lake after the storm cleared out.  Trailer is about 35', about 5000 lbs with the boat.  

IMG-0245.thumb.jpg.d43f3d654e763f2547b4c1e0035e457d.jpg

We sold our 2008 Harris Flotebote 250 and picked up a brand new Harris Mariner 230. Looks just like yours!

 

 

Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Conditions for Meeting a Cold Start   The ignition voltage is between 10 and 15 V. The barometric pressure (BARO) is more than 75 kPa. The engine coolant temperature (ECT) at start-up is less than 42°C (108°F). The intake air temperature (IAT) is between 2–32°C (36–90°F). The engine is OFF for greater than 6 hours or the following conditions must be met: The start-up IAT minus start-up ECT are within 12°C (22°F). The start-up ECT minus start-up IAT are within 50°C (90°F). Fuel level is between 25 and 75 %.   Circuit/System Verification Verify that all I/M System Status indicators report YES, and that no I/M Test DTCs are present.If any I/M Test DTCs are set Refer to Diagnostic Trouble Code (DTC) List - Vehicle. If no I/M Test DTCs are set All OK. Inspection/Maintenance (I/M) System Set Procedure   Warning: Refer to Road Test Warning. Note: Do NOT touch the accelerator pedal until told to do so. A change in TP Sensor angle or an increase in engine speed may invalidate this portion of the test.   Note: An I/M Test DTC will not be stored or erased from the ECU except at the end of trip processing, which occurs 5 s after ignition OFF.   Ensure that the vehicle meets the conditions for a cold start listed above. If the EVAP I/M System Status indicator displays NO, perform the EVAP Service bay test if applicable. Turn OFF all of the accessories; HVAC system, other electrical loads, including aftermarket/add-on equipment, etc., and open the hood.   Set the vehicle parking brake and ensure the vehicle is in park for automatic transmission or neutral for manual transmission.   Start and idle the engine for 2 min.   Close the hood, release the parking brake and Accelerate at part throttle to 72–80 km/h (45–50 mph) with this speed maintained until the engine reaches operating temperature, 8–10 min.   Continue operation under these conditions for an additional 6 min.   Accelerate at part throttle to 90 km/h (55 mph) with this speed maintained for 2 min.   Release the accelerator pedal for at least 10 s. This will allow the vehicle to enter the decel fuel cut off.   Safely stop the vehicle, with the engine in drive for automatic or neutral with the clutch pedal depressed and parking brake applied for manual. Allow the vehicle to idle for 2 min.   Shift the vehicle to park for automatic and neutral for manual. Turn OFF the ignition and exit the vehicle. Do NOT disturb the vehicle for 45 min.   Observe the Inspection/Maintenance (I/M) System Status with a scan tool. All of the I/M System Status indicators should display YES.   If the EVAP I/M System Status indicator displays NO, turn OFF the ignition, ensure that the vehicle meets the conditions for a cold start, and repeat steps 6-11 three more times, or until the EVAP I/M System Status indicator transitions to YES. If the indicator continues to display NO, refer to the Inspection/Maintenance (I/M) System DTC Table to identify the DTCs that did not run.   If any of the I/M System Status indicators display NO, refer to the Inspection/Maintenance (I/M) System DTC Table for the indicator which did not display YES. The I/M System DTC Table identifies the DTCs associated with each I/M System Status Indicator.   Observe the I/M Test DTC information with a scan tool. Verify there are no I/M Test DTCs present. If an I/M Test DTC is set, diagnose the DTC using the Diagnostic Trouble Code (DTC) List - Vehicle and refer to Inspection/Maintenance System Check.   Observe the engine DTC information with a scan tool. Verify no DTCs are present. If a DTC is set, diagnose using the Diagnostic Trouble Code (DTC) List - Vehicle. After repairs, perform the Inspection/Maintenance Complete System Set Procedure to verify no further DTCs are set.       Looks like one procedure to me.  Repeated as necessary.
    • My 2020 AT4 6.2 has had the valve spring issue addressed at ~200 miles, front cover/pump replaced at 18k, water pump at 34k and idler pully at 65k.  I would agree with ditching by 100k unless you elect to go with upgraded hardware...say built 10l80 and an lt4 or l8p swap.
    • I also need one of your modules for my 1993 chevy c2500 7.4 Thanks! My email is [email protected]
    • Chevy needs to do a black regular cab short box SS model with the new 6.6L.  400SS.
    • You might find the drive cycle you need somewhere on charm.li (website), otherwise I suggest a subscription to alldata.com to get them for your truck.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...