Jump to content

Rough Country mixup.

Byron Greenleaf
 Share

Recommended Posts

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
Posted

So I bought this 2015 Sierra and it needs ball joints replaced. Only problem is I can’t get a straight answer about If I need new upper control arms or stock ones put back in. It currently has Rough Country arms but when I asked RC they told me that they should not be installed. ALSO I’m not 100% sure in the size of the lift. RC says it’s a 5” but it doesn’t seem like it. Just looking for some input. Thanks 

E5B248F8-9884-47C5-838A-C0D034957450.jpeg

D08BA8D5-4FC6-4950-990E-78F36C067CE1.jpeg

080BD0C3-E5CF-4151-B9C2-157598045C87.jpeg

14 Silvy Enthusiast

14 Silvy

Posted
Posted

Thats the 3.5 lift with RC arms. It has those to correct the upper balljoint angles. I would go back ith them or drop it back down to no more than a 2.5 level to help all the angles. Also you could go bigger to the 5 inch and angles would be flat like factory.

Sent from my SM-G988U using Tapatalk

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
  • Author
Posted

Thank you. I measured from center of the wheel to fender and I’m at 25”. What leveling kits would you recommend. I’m already rubbing when the wheel is turned all the way. Is there a good 4” or 5” that might not be so stiff. Any bump is pretty jarring. 

Donstar Senior Enthusiast

Donstar

Posted
Posted

This is a pretty rough (no pun intended) way to lift your truck.  Returning to stock or a proper lift, as already suggested, are the best options. You have a nice looking truck and you probably purchased it in part due to the lifted look.  I'd take it to a reputable 4x4 shop and have a proper 6" lift installed. It may cost more than you would like for now but the ride, safety and durability are worth the initial expense, imo.

IronVilkas Enthusiast

IronVilkas

Posted
Posted (edited)
9 hours ago, Byron Greenleaf said:

Thank you. I measured from center of the wheel to fender and I’m at 25”. What leveling kits would you recommend. I’m already rubbing when the wheel is turned all the way. Is there a good 4” or 5” that might not be so stiff. Any bump is pretty jarring. 

Your not really going to find a leveling kit above 3.5 inches because it causing excess wear and ride stiffness. You would want to go with a 4-4.5 inch lift at least depending on what tire size you want. 

 

Zone/BDS are good companies to look at for 4.5 to 6inch lifts. Fabtech and CTS makes a good 4 inch lift as well

Edited by IronVilkas
IronVilkas Enthusiast

IronVilkas

Posted
Posted

yea for sure a smoother ride. The angle on your control arms are pretty drastic rn. They should be back to stock/level with the BDS, plus the new shocks will be quality

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
  • Author
Posted
11 hours ago, IronVilkas said:

yea for sure a smoother ride. The angle on your control arms are pretty drastic rn. They should be back to stock/level with the BDS, plus the new shocks will be quality

Do I need to go with coilovers for a decent ride?

Donstar Senior Enthusiast

Donstar

Posted
Posted

Good luck with your project!  Hopefully you found a business that you trust and will make your truck ride and perform better than new!  My caution at this point is choice of height.   I find that lifted truck owners have a tendency to want to go higher rather than lower.  A 4" lift sounds like a practical height, but 6" has the wow factor, imo.  I don't have a lifted truck but I do know what it's like to settle for fear of being too bold.  If you're spending this amount of money to significantly alter your truck,  make sure you don't regret spending a little extra to get a lot more!

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
  • Author
Posted
12 hours ago, IronVilkas said:

yea for sure a smoother ride. The angle on your control arms are pretty drastic rn. They should be back to stock/level with the BDS, plus the new shocks will be quality

Do I need to go with coilovers for a decent ride?

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
  • Author
Posted
28 minutes ago, Donstar said:

Good luck with your project!  Hopefully you found a business that you trust and will make your truck ride and perform better than new!  My caution at this point is choice of height.   I find that lifted truck owners have a tendency to want to go higher rather than lower.  A 4" lift sounds like a practical height, but 6" has the wow factor, imo.  I don't have a lifted truck but I do know what it's like to settle for fear of being too bold.  If you're spending this amount of money to significantly alter your truck,  make sure you don't regret spending a little extra to get a lot more!

 

Thanks. Good point on going big but it’s a daily driver and I still need the sucker to fit in the garage preferably. Not much of a difference though between a 4” and 6” in price. My 33” would probably look a little small if I went taller. 

14 Silvy Enthusiast

14 Silvy

Posted
Posted

I'm running the RC 5 inch bracket lift with a 2 inch level and a add a leaf in the rear. I also added a 1.5 zone body lift. I bought the Rc lifted struts with the kit and it rides very well. I am running 22x12 with a 35x12.50 with no rubbing. A lot of people on here down RC but I haven't had a single issue with it.355c66fbead91d3340ac0bb7539982fb.jpg12afeb8deb87e54dd4a97128f35ddf83.jpg

Sent from my SM-G988U using Tapatalk

IronVilkas Enthusiast

IronVilkas

Posted
Posted
20 hours ago, 14 Silvy said:

I'm running the RC 5 inch bracket lift with a 2 inch level and a add a leaf in the rear. I also added a 1.5 zone body lift. I bought the Rc lifted struts with the kit and it rides very well. I am running 22x12 with a 35x12.50 with no rubbing. A lot of people on here down RC but I haven't had a single issue with it.355c66fbead91d3340ac0bb7539982fb.jpg12afeb8deb87e54dd4a97128f35ddf83.jpg

Sent from my SM-G988U using Tapatalk
 

I was very close to getting one of these kits. It keeps all the suspension angles stock just moves them down and keeps the stock knuckle and with the new struts it would probably ride very nice. The other benefit is it doesnt increase the front track width like the BDS and other lifts do

IronVilkas Enthusiast

IronVilkas

Posted
Posted
21 hours ago, Byron Greenleaf said:

Do I need to go with coilovers for a decent ride?

I think youll get a good ride with or without coilovers Since BDS makes a quality lift. The coilovers would make it that much better, I would say you need to ask someone who has the coilovers if its worth it since they are usually pricey. 

Byron Greenleaf Enthusiast

Byron Greenleaf

Posted
  • Author
Posted

Yeah I’m talking with BDS. I’m a Michigander and want to support them. Also helps they make quality products. But yeah it’s expensive, buy once cry once? 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      seat base height *lowering* (base 40/20/40 seat, 2026 1500 WT std cab)

      By bwiese · Posted

      Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...