Jump to content

Recommended Posts

Posted

I will do my own oil changes and maintenance until no longer able to.

  • Like 2
Posted
22 minutes ago, diyer2 said:

I will do my own oil changes and maintenance until no longer able to.

I already can not in the winter and I don't think the cow will let me milk her just 6 months of the year. 

? 

 

Kidding aside; I don't let dealers do anything but unavoidable recalls. I have a trusted and groomed local shop who satisfies my requirements for competence, talent and cost. They are getting harder to find too. Hold on to the ones you can find. 

  • Like 1
Posted (edited)

https://www.consumer.ftc.gov/articles/0138-auto-warranties-routine-maintenance

 

Quote

Do I have to use the dealer for repairs and maintenance to keep my warranty in effect?

No. An independent mechanic, a retail chain shop, or even you yourself can do routine maintenance and repairs on your vehicle. In fact, the Magnuson-Moss Warranty Act, which is enforced by the FTC, makes it illegal for manufacturers or dealers to claim that your warranty is void or to deny coverage under your warranty simply because someone other than the dealer did the work. The manufacturer or dealer can, however, require consumers to use select repair facilities if the repair services are provided to consumers free of charge under the warranty.

That said, there may be certain situations where a repair may not be covered. For example, if you or your mechanic replaced a belt improperly and your engine is damaged as a result, your manufacturer or dealer may deny responsibility for fixing the engine under the warranty. However, according to the FTC, the manufacturer or dealer must be able to demonstrate that it was the improper belt replacement — rather than some other defect — that caused the damage to your engine. The warranty would still be in effect for other parts of your car.

Will using 'aftermarket' or recycled parts void my warranty?

No. An 'aftermarket' part is a part made by a company other than the vehicle manufacturer or the original equipment manufacturer. A 'recycled' part is a part that was made for and installed in a new vehicle by the manufacturer or the original equipment manufacturer, and later removed from the vehicle and made available for resale or reuse. Simply using an aftermarket or recycled part does not void your warranty. The Magnuson-Moss Warranty Act makes it illegal for companies to void your warranty or deny coverage under the warranty simply because you used an aftermarket or recycled part. The manufacturer or dealer can, however, require consumers to use select parts if those parts are provided to consumers free of charge under the warranty. 

Still, if it turns out that the aftermarket or recycled part was itself defective or wasn't installed correctly, and it causes damage to another part that is covered under the warranty, the manufacturer or dealer has the right to deny coverage for that part and charge you for any repairs. The FTC says the manufacturer or dealer must show that the aftermarket or recycled part caused the need for repairs before denying warranty coverage.

 

Edited by elcamino
Posted

I do my own, unless under lease maintenance.

Too many people rushing and not doing a diligent job.

Well said by many others.

Bottomline, sloppy maintenance might lead to a failure that’s your problem, sludge, or overfilling...


Sent from my iPad using Tapatalk

  • Like 1
Posted

It's $80 at my dealer for an 8-qt. oil change and tire rotation. It costs me about $50 for the oil and filter. I don't have the equipment to easily do the tire rotation. It's worth the extra $30 to me to let the dealer do it. For that $30, my tires get rotated, I don't make a mess in my garage and I don't have to deal with the used oil. 

Posted

Ridiculous.
I change my own for $40.
Mobil 1 0w20 12 qt box,
(oil is in a bag inside a box like a wine box),
at walmart is $49. Ac delco filters are $7.
I get 24 qts ( two boxes) of oil and 3 filters for around $120 = $40 . At this price I change it every 3500-4000 miles. Both of my 2018 5.3's.
I wouldn't let the dealer touch my trucks for an oil change. The last time they spilled oil all over, dirty hand prints and it wasn't full. 1/2 qt low when I got home.
They must have spilled the rest.
They let the car clean up kids do oil changes. No thanks.

Sent from my Pixel 3 using Tapatalk

Posted
1 hour ago, dieselfan1 said:

Ridiculous.
I change my own for $40.
Mobil 1 0w20 12 qt box,
(oil is in a bag inside a box like a wine box),
at walmart is $49. Ac delco filters are $7.
I get 24 qts ( two boxes) of oil and 3 filters for around $120 = $40 . At this price I change it every 3500-4000 miles. Both of my 2018 5.3's.
I wouldn't let the dealer touch my trucks for an oil change. The last time they spilled oil all over, dirty hand prints and it wasn't full. 1/2 qt low when I got home.
They must have spilled the rest.

They let the car clean up kids do oil changes. No thanks.

Sent from my Pixel 3 using Tapatalk
 

Actually they threw it away! I get my bottles back and found that they leave about 2 ounces per quart for quarts and four to five ounces per gallon jug in the containers. The dump the containers so fast......you get the idea......

Posted
4 hours ago, elcamino said:

You can claim this all you want but the minute something does go wrong with your vehicle GM will ask you or the dealer where it has been serviced at and if it’s not a GM certified mechanic good luck having them warranty anything.  Like I said, GM has WAY more money then you do!  
For the $20 to $30 difference. I’ll let them pick up my truck do it, deliver it back, and when something breaks, guess what, the records show they have done all the maintenance on the vehicle. 
 

As for someone else commenting on being lazy or too fat. I’m far from that, I love tinkering with my truck. Heck my father has a shop, but when the truck is under GM Warranty, you best believe I’ll let the certified guys handle it till it’s up. 

Posted

Dealers have bulk oil tanks. Unless you are bringing them your own oil (who does that?), they aren’t pouring it out of quart bottles all day and leaving a few drops in each one. Imagine the waste.

  • Like 1
Posted

You'd think an oil change and tire rotation is brain surgery......I can get an oil change done in 20 minutes dragging ass and the rotation done in another 20 with a floor jack and jackstand.  If you don't have an hour of time available in your life, you should reconsider how you're living.    

Posted
2 hours ago, TNTSilverado said:

You can claim this all you want but the minute something does go wrong with your vehicle GM will ask you or the dealer where it has been serviced at and if it’s not a GM certified mechanic good luck having them warranty anything.  Like I said, GM has WAY more money then you do!  
For the $20 to $30 difference. I’ll let them pick up my truck do it, deliver it back, and when something breaks, guess what, the records show they have done all the maintenance on the vehicle. 
 

As for someone else commenting on being lazy or too fat. I’m far from that, I love tinkering with my truck. Heck my father has a shop, but when the truck is under GM Warranty, you best believe I’ll let the certified guys handle it till it’s up. 

Fear mongering.

  • Thanks 1
Posted

Its a 2 beer job - and who doesnt like day drinkin? Rotella gas truck had a rebate ending up at $9 per 5qt - thats good oil for a hell of a price though normally decent synthetic oil is around $20 per 5g. 50 bones is about standard these days with a free change every 4 changes due to the 2 qts left over after each change...

Sent from my SM-G975U using Tapatalk

  • Like 1
Posted

I'd hate to think of how many quarts of oil I've poured doing them myself for over 35 years.  Of course now I've got 3 Chevy's and a Pilot to do, not to mention Quad, ZTR, outboard, tiller, log splitter... holy crap.  If a good coupon shows up I will allow the dealer to do the wifes' Pilot.  I will get my freebie and then do them myself.  I recently started using the Rotella myself, buy 5.3 filters by the 6pk.  I bottle the old and take it to the local tech who burns it in his shop HVAC.  

Posted
6 hours ago, dieselfan1 said:

Ridiculous.
I change my own for $40.
Mobil 1 0w20 12 qt box,
(oil is in a bag inside a box like a wine box),
at walmart is $49. Ac delco filters are $7.
I get 24 qts ( two boxes) of oil and 3 filters for around $120 = $40 . At this price I change it every 3500-4000 miles. Both of my 2018 5.3's.
I wouldn't let the dealer touch my trucks for an oil change. The last time they spilled oil all over, dirty hand prints and it wasn't full. 1/2 qt low when I got home.
They must have spilled the rest.
They let the car clean up kids do oil changes. No thanks.

Sent from my Pixel 3 using Tapatalk
 

That is why I built this.  Out of all the oil changes I do I get a couple of qts every month from what drains out of the bottles after an oil change.  I use it in lawn equipment or when I get an old beater that uses oil every 1000 miles.  I can add more to it to hold as many qts or jugs as needed.  I just stopped at 5..  What I do is let the qts sit  on their side over night then dump them on here.  That way the oil is on the side and then drains right out and not trying to drip from the bottom of the container.

 

image.thumb.png.8c66628130d5bc4a88401e0e0e618c92.png

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Did have to make 1 modification because of the WeatherTech rear mud flaps and that was needing 3 longer screws than what came with the install package. 😄
    • Picked up the liners yesterday. Installed passenger side WITHOUT any modifications. All mounting holes lined up perfectly. Rain is interfering today with drivers side. Very Happy! Will add pics when finished
    • As a matter of amusement I’ll leave this conversation with this. Do you beat the government average fuel estimate? Statistics are a guide to me. Not a rule. Someone once said I have to have the last word. If true and possible may be. I’ll blame that on working in a family business.
    • That is a fair point, and I agree that trying to log “everything in the truck” would be the wrong direction.   There are a lot of modules and a lot of traffic. If the product became a full-truck datalogger, the amount of data would get huge very quickly, and most owners would never use it.   I think the first useful version would need to be narrow: - powertrain-side event evidence - selected high-value parameters - communication / voltage / reset events - pre/post event window - short report first, raw log only as backup   One distinction I should make is between active OBD/PID polling and passive bus capture. If you are polling PIDs through OBD, then yes: the more parameters you request, the lower the effective sample rate becomes, and you are adding diagnostic traffic to a vehicle that is already busy running itself. With passive CAN capture, the recorder is not asking all the modules for data. It is listening to traffic that is already on the bus. So it does not consume vehicle bus bandwidth in the same way that a scan tool polling hundreds of PIDs would. But your point still applies in a different way.   Even if passive capture does not add bus traffic, the recorder still has limits: - processing rate - storage rate - timestamp accuracy - decoder workload - event filtering - report size - user attention span   So the answer cannot be “log everything and let the user figure it out.” The product would need to store enough raw evidence to be useful, but only decode, graph, and present the important parts around the event.   A practical report should probably show: - what triggered the capture - how much pre/post data was preserved - which selected parameters changed - how those values compared to baseline - whether the same pattern happened before - whether any voltage, reset, bus-off, lost-message, or communication fault occurred - selected graphs around the event - raw data only as supporting evidence   So I agree with you. More data is not automatically better. The real product is the reduction from raw data into a useful event report.
    • That makes sense, and I agree with most of that.   I think the product would need both: 1. a default powertrain template, so it is useful out of the box; 2. user-selected priority parameters, so the owner or shop can choose what they want to see first.   Different users are going to care about different things. One owner may care about oil pressure and voltage. Another may care about misfire trend, AFM/DFM behavior, or U-codes. A shop may want communication events and repeatability first. Your baseline point is probably the most important one. Raw data is not very useful unless the report can show what normal looked like for that vehicle under similar conditions.   The way I would think about it is: - start with a basic known-good baseline - learn normal behavior for that specific vehicle over time - allow the event to be overlaid against baseline - show whether the event was a one-time spike or a repeatable pattern - provide a simple severity level, but with clear limits on what that severity means   For example, early severity could be something like: - Info: event captured, no obvious abnormal pattern - Watch: value moved outside baseline, but not repeated - Warning: repeatable abnormal pattern under similar conditions - Critical: communication loss, voltage drop, bus-off, reset, or severe repeated event   I would not want the first version to say “replace this part.” That would be overclaiming unless there is repair-confirmed data behind it. It would be more honest to say “this pattern deserves inspection.”   On the OBD port question, I think OBD absolutely has a role. OBD is probably the right place for: - DTCs - freeze frame - VIN - calibration information - normal scan-tool parameters - Mode 6 / enhanced diagnostic data if available The reason I am still looking at an ECM-side recorder is that the failure may happen before anyone connects a scan tool. If the owner plugs in a scanner after the event, the pre-event evidence may already be gone unless the ECU happened to save it. So I do not see this as “OBD versus ECM-side.” I see it more like: - ECM-side recorder: always armed, rolling buffer, event evidence - OBD/DLC companion: DTCs, freeze frame, VIN, calibration, normal scan data - phone/cloud: status, notes, upload, report generation, notifications   I agree that phone connection and push notifications would be useful. I just would not want the phone or cloud connection to be required for capture. The recorder should save the event locally even if the phone is not connected. The phone should help with event marking, download, notes, upload, alerts, and report viewing.   For a default GM V8 event report, would this list make sense? - RPM - calculated load / MAP - throttle position - vehicle speed - gear / torque converter state if available - coolant temperature - oil pressure - oil temperature if available - battery voltage - commanded AFM/DFM state if available - actual AFM/DFM state if available - misfire counters / roughness by cylinder if available - fuel trims - relevant U-codes / communication events - bus-off / lost periodic message / module reset / voltage drop events Which of those would you remove, and what would you add?
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...