Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

RobinhoodNC Enthusiast

RobinhoodNC

Posted
Posted

I'm amazed how ridiculous is the stock front suspension downtravel on these trucks. I initially measured for reference exactly 1,5" when I had the 3" front spacers installed with RC forged UCAs, difference from hub to fender. This was without the bumpstop rubber, UCA was resting on the chassis. I thought that the quite poor ride quality was due to that.

 

So I decided to lower the truck to get a bit more downtravel, to 2.25" (readylift). And to my surprise I didn't get that 3/4 inch back in downtravel... No...only a mere 1/5" more ! And the UCA wasn't even touching the bumpstop ! Strut was simply bottomed out...So my 2.4t 20feet long 4x4 truck has hardly 2,4" of downtravel on its front struts. Lol. Even my business car Kia Sportage has more wheel travel...This is maybe explained by the so stiff springs they have. They hardly compress when jacking down. Then  I did put back the rubber bumpstops but these are only slightly in contact with the UCAs. So with a 2 inch level kit on stock UCA I guess that full downtravel is still almost here, that's why ride quality isn't too much impacted. 

 

Know I just need to find longer/smoother springs...but impossible to find the spring rate on mine.

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

ZX14R BUSA KILLER Enthusiast

ZX14R BUSA KILLER

Posted
Posted (edited)

I went with a Rough Country 3" lift leveling kit. 20" KMC DemoDog Wheels with -18 Offset, and with 33" Offroad Tires.

20200304_091621.jpg

20200306_080154_HDR.jpg

Edited by ZX14R BUSA KILLER
Riddick1224 Enthusiast

Riddick1224

Posted
Posted

I’m looking to lower the back of my 2016 to level the truck out. Any suggestions?


Sent from my iPhone using Tapatalk

mcdavis Enthusiast

mcdavis

Posted
Posted
On 4/13/2020 at 10:36 PM, Riddick1224 said:

I’m looking to lower the back of my 2016 to level the truck out. Any suggestions?


Sent from my iPhone using Tapatalk

I've read that you can just remove the blocks from the leaf springs and it'll drop the rear about 1 1/2". Google it, lots of info on it. Doesn't make it perfectly level, but makes it look much better from what I've seen.

Bensjamming Enthusiast

Bensjamming

Posted
Posted

Why does it matter with the RC 2' spacers if you install the bolts from the top down or if you have the nuts on the top of the strut since neither the head or not come into contact with the spacer itself?

mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted (edited)
38 minutes ago, Bensjamming said:

Why does it matter with the RC 2' spacers if you install the bolts from the top down or if you have the nuts on the top of the strut since neither the head or not come into contact with the spacer itself?

The one thing I see with doing the bolts from the top down is that changing out the struts when its needed wont be too easy. From bottom up, it is a much simpler job. However. The bolts used are too long and would cause interference. Some have solved this by cutting down the bolts. But with that being said, I did follow the Rough Country installation directions and installed them from the top down. Hopefully it wont be for awhile but dreading the time when the struts need to be changed out...

Edited by mikeyk101
Bensjamming Enthusiast

Bensjamming

Posted
Posted
2 hours ago, mikeyk101 said:

The one thing I see with doing the bolts from the top down is that changing out the struts when its needed wont be too easy. From bottom up, it is a much simpler job. However. The bolts used are too long and would cause interference. Some have solved this by cutting down the bolts. But with that being said, I did follow the Rough Country installation directions and installed them from the top down. Hopefully it wont be for awhile but dreading the time when the struts need to be changed out...

I was thinking the same thing. Is the interference with the cv axle then I take it? If so I might just measure the thickness of the stock configuration from bolt head to end of stock bolt and then just add the thickness of the spacer and cut the bolts right away. Just seemed like alot more work then needed when they could be put in the other way.

mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted

Yes, it is the CV joints that get in the way. If I had a way to properly cut the bolts down, I would have gone that way myself. I guess I could have just run out to the Menards or Home Depot and got the right sized bolts but at the time, part of the front end was in pieces so I had no way to get there, LOL!

Bensjamming Enthusiast

Bensjamming

Posted
Posted

I ended up just taking it all apart and doing it the right way. Start to finish it took me about 45 minutes to do both sides by myself this morning. Was way easier then I thought it was going to be. 

  • Like 1
superdave160 Enthusiast

superdave160

Posted
Posted

I installed the Rough Country spacers on my 2017 Silverado 1500 this weekend.  I could not get the upper ball joint to separate.  I didn't want to use a fork and damage the ball joint or the boot.  The tie rod ends popped right out though.  Since the ball joints would not separate, I couldn't get one of the strut bolts to go in from the top because the axle shaft was in the way.  I put the bolt in from the bottom and noted that there was very little clearance between the end of the bolt and the axle shaft.  I ended up adding some washers to the head of the bolt to increase the clearance.  That gave me enough clearance and still had enough thread penetration for the lock nut to work.  I measured at the front fenders through the center line of the wheels, and they went from 36 1/4 to 38 inches from the ground.

  • Like 1
jgraves13 Enthusiast

jgraves13

Posted
Posted
I installed the Rough Country spacers on my 2017 Silverado 1500 this weekend.  I could not get the upper ball joint to separate.  I didn't want to use a fork and damage the ball joint or the boot.  The tie rod ends popped right out though.  Since the ball joints would not separate, I couldn't get one of the strut bolts to go in from the top because the axle shaft was in the way.  I put the bolt in from the bottom and noted that there was very little clearance between the end of the bolt and the axle shaft.  I ended up adding some washers to the head of the bolt to increase the clearance.  That gave me enough clearance and still had enough thread penetration for the lock nut to work.  I measured at the front fenders through the center line of the wheels, and they went from 36 1/4 to 38 inches from the ground.

If you ever need to get the ball joint separated, just hit the spindle with a hammer until it jiggles itself loose


Sent from my iPhone using Tapatalk
superdave160 Enthusiast

superdave160

Posted
Posted
19 minutes ago, jgraves13 said:


If you ever need to get the ball joint separated, just hit the spindle with a hammer until it jiggles itself loose


Sent from my iPhone using Tapatalk

Trust me, I hit it with a hammer!

  • Like 1
  • 4 weeks later...
Pig Sooie 4 Enthusiast

Pig Sooie 4

Posted
Posted

Hey guys! I am new to the board but i bet i have read most of the 496 pages on this topic. I am interested in the 2.5 Rough Country lift kit and was wondering everyones thoughts? I have always had the 2 inch rough country kit on my previous trucks but was interested in this kit due to the rear block. I have 295/55/20 Nitto Ridge Grapplers on this truck now. I received a quote from the dealership i purchased the truck from and the kit plus the labor was quoted at $1200. I thought that was extremely high given the kit is $450. I was wondering what everyones thoughts were on the kit and also the price i was given. Any help is appreciated!

acinquegrana Enthusiast

acinquegrana

Posted
Posted

Finally bit the bullet and got wheelsand tires. My 2016 Silverado 1500 Rally 2LT with ready lift 2.25 and UCA and Zone add leafs.

I went with 2019 GMC Sierra SLT replica wheels in gloss black and LT275 65 R20 Duratracs. Upgrading from 285 45 22 bridgestone duellers. What a difference. You would never know these are a 10 ply tire. Great ride.

To prevent UCA rub, I fabricated some steering stops and tack welded them to the lower control arm. I made them over size and then ground them down to a perfect fit. Lost 6 degrees of turning radius as indicated on the dash, but i dont care about that. I rarely max out my steering. I did this so I didnt have to run a wheel spacer. Trimmed the corner of my mud flaps too. No rubbing at all982e4efd068e0214a1c489ee4a0979b9.jpg

Sent from my SM-G950U using Tapatalk

  • Like 1
acinquegrana Enthusiast

acinquegrana

Posted
Posted

More pics. Pardon the excessive fluid film on the control arms lol. 06140ba1dafd8ae5df655596db4aba49.jpg15722f2b551ea1211f1026e9af359081.jpg6e751727a3466e897d112b640b02e82a.jpg420872c781b78649132dd738a3000e83.jpg

Sent from my SM-G950U using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,894
    Total Members
    8,960
    Most Online
    TopBo
    Newest Member
    TopBo
    Joined

  • Who's Online   1 Member, 0 Anonymous, 871 Guests (See full list)

  • Latest Articles

  • Posts

    • davester
      New to Me 2010 SLE (Quirks, Issues)

      By davester · Posted

      not all plugs will be used.  gm uses more generic harnesses that support most/all options, and if your truck doesn't have a specfiic option, the plug won't be used (commonly will have a dummy insert in the plug , or it'll be taped up, but some may just be left as is).  But it's sldo possible some p.o. has installed the wrong/cheaper parts that aren't correct for your vehicle...
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • lowrider
      Range RA007 DFM Module

      By lowrider · Posted

      I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou
    • Tyler Gibbs
      2022 2500HD with a new RSI SmartCap

      By Tyler Gibbs · Posted

      Is it an optical illusion in the pic or is the truck really squatting that much horribly?
    • fm2176
      It's Been a Long Time...

      By fm2176 · Posted

      My initial introduction was here.  It's hard to believe that I last posted in February 2013, having just deployed to Kyrgyzstan.  Since then, I've retired from the military and the 2006 Sierra SLT Z71 that first brought me to these pages was lost.  I went forward to Afghanistan in March 2013 and did a lot of sitting behind a computer on brigade staff.  Within 18 months of getting back to the States, I was selected for Drill Sergeant duty, after which I moved back to Virginia (my home state and where I served from 2004-2008).  That '06 Sierra did a lot of driving between Louisiana, Georgia, and Virginia, and ended up with nearly 320k miles by 2022.  By then, the registration had been expired for a couple of years, but the pandemic had all but eliminated tickets for such transgressions.  Admittedly too, I usually drove my wife's SUV or son's car the 2-3 times a week I had to report to work.  Teleworking sure was fun while it lasted.   I started my retirement leave four years ago and stored the Sierra at my sister's house.  A big mess was made when her fiancé passed while she was taking care of business out-of-state in late-2024, and his son pretty much mismanaged everything to do with the estate.  Even so, I was assured that my truck was safe... until it wasn't.  I found out that my truck had been scrapped about four months after the son took over everything.  There's nothing I could do; I'm 1000 miles away and it was technically abandoned property since he'd even trespassed my sister from her own house (she had no claim to it as she wasn't married, and the fiancé was the sole owner).     Anyway, today I got my second Sierra.  This is a 2010 SLE 2WB CCSB with a little over 200k miles on it.  It's got the 5.3L I'm familiar with and should handle what I need it for.  Hauling stuff that won't fit in the Transit Connect (yep, I sold out, but that's the wife's vehicle) and towing a few times a year tops.  The price seemed decent, considering how much people sell their trucks for in the Deep South: $4500.  I've seen similar trucks listed for more than double that.  I got it from a coworker who left his tag on until we transfer the title next week (Louisiana requires a notary for transfers), so I've been driving it all day.  The rear speakers don't work, which is one of the things that brought me back to these forums earlier.  I can't say how active I'll be as a poster, but I'll be scouring the archives while I find out every little thing I can about the 2010s and particular nuances/problems with my truck.   It's definitely not a GMC, but I got another Willys Jeep a few months back as well, so I'm almost at the same place I was when I first joined gm-trucks.com.  My old 1960 DJ3A was sold back around 2010 or 2011; my current Jeep is a 1946 CJ2A.  So, I've got a slightly newer GMC and a much older Jeep.  I kind of wish I still had that F-250 I had way back when too.  The Dakota is long gone and was technically my brother's truck, though I had it registered and insured.  The F-250 had to go when my grandmother's house was foreclosed on due to mismanagement around 2012 or so.     Hopefully anyone that made it this far isn't too annoyed.  I tend to be long-winded, but I'll be doing more reading than posting in the coming months.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...