Jump to content

Recommended Posts

Posted
On 2/24/2021 at 12:52 PM, Kclyatt said:

Update....Few months into sealing my rear glass and happy to report no further leaks. I recently sealed up my spoiler as a added guarantee because as we can see GM does not have our best interests in mind. I used door trim from Lowes and this particular type has ridges to help with the trim tool to push into the tight space and also has adhesive on the back to hold into place once set. The third brake light I used clear silicone (same type 3M) since that gap was too tight for trim.

 

Hope my enthusiasm to prevent future leaks helps another in this exclusive club of leakers!

trim.1.jpg

trim.2.jpg

Trim.3.jpg

Thank you for sharing this. Can you advise what 3m silicone you used and possibly provide a link? 
 

Thanks again,

JMF

Posted
10 hours ago, jftwist said:

Thank you for sharing this. Can you advise what 3m silicone you used and possibly provide a link? 
 

Thanks again,

JMF

 

4F71134E-0FEC-474F-907F-8679549FEDBE.png

Posted
28 minutes ago, Kclyatt said:

 

4F71134E-0FEC-474F-907F-8679549FEDBE.png

Thank you very much for your assistance. 
 

JMF

Posted

There is another type of self leveling 3m adhesive I believe that is called out in the TSB


Sent from my iPhone using Tapatalk Pro

Posted

Just curious if anyone who has a topper/camper shell if that's helped prevent or stop the amount of water coming in the cab from the rear window? 

Posted (edited)

TSB Sealing Repair Completed – UPDATE

 

Quick background – Picked up my ’21 Sierra on 12/4/20. Within 10 days of ownership I had the leak on both sides at the top of the slider. Dealer completed the TSB, and I could see a heavy bead of the sealer that was laid across the top frame of the slider.  After the TSB was done I didn’t see any leaks and continue to check very closely after every rain. I have a small towel sitting on top of the rear seat back rest just in case the slider starts leaking again. About a month ago during a steady rain I saw a drop of water from the same location - literally a few drips where it was barely leaking, but the towel on the seat back rest was dry to the touch as was the carpeting.

 

As others in this thread have suggested and since it was barely leaking I decided to try the flowable silicone (permatex 81730) rather than have the truck torn apart again. When we had a warm day I cleaned the top of the slider as best I could and also taped off the top of the glass on the slider to try and minimize the mess. I used a full tube of the permatex and made a few passes across the top of the slider frame, being careful to not overfill the area. As other posters have mentioned that have used this product it is thin and runny, so being careful minimizes the clean up.

 

Since using the flowable silicone 4 weeks ago we have had both snow and rain. Over the past week we have had significant rain, including long periods of drizzle, solid rain and heavy down pours. So far no leaks, so the effort was well worth it. I can see along the top of the slider frame where the flowable silicone has dried there is an even layer of silicone across the complete gap. It looks like the permatex product took care of any small gaps that the TSB work didn't completely seal. So far I’m really impressed with the permatex product and will use it again should I see a small leak in the future.

 

Pic below of where it was leaking and also of the permatex product used. Thanks to everyone that recommended this product and the idea.

 

 

leak.JPG

permatex.JPG

Edited by DSW1519
Posted
4 hours ago, DSW1519 said:

TSB Sealing Repair Completed – UPDATE

 

Quick background – Picked up my ’21 Sierra on 12/4/20. Within 10 days of ownership I had the leak on both sides at the top of the slider. Dealer completed the TSB, and I could see a heavy bead of the sealer that was laid across the top frame of the slider.  After the TSB was done I didn’t see any leaks and continue to check very closely after every rain. I have a small towel sitting on top of the rear seat back rest just in case the slider starts leaking again. About a month ago during a steady rain I saw a drop of water from the same location - literally a few drips where it was barely leaking, but the towel on the seat back rest was dry to the touch as was the carpeting.

 

As others in this thread have suggested and since it was barely leaking I decided to try the flowable silicone (permatex 81730) rather than have the truck torn apart again. When we had a warm day I cleaned the top of the slider as best I could and also taped off the top of the glass on the slider to try and minimize the mess. I used a full tube of the permatex and made a few passes across the top of the slider frame, being careful to not overfill the area. As other posters have mentioned that have used this product it is thin and runny, so being careful minimizes the clean up.

 

Since using the flowable silicone 4 weeks ago we have had both snow and rain. Over the past week we have had significant rain, including long periods of drizzle, solid rain and heavy down pours. So far no leaks, so the effort was well worth it. I can see along the top of the slider frame where the flowable silicone has dried there is an even layer of silicone across the complete gap. It looks like the permatex product took care of any small gaps that the TSB work didn't completely seal. So far I’m really impressed with the permatex product and will use it again should I see a small leak in the future.

 

Pic below of where it was leaking and also of the permatex product used. Thanks to everyone that recommended this product and the idea.

 

 

leak.JPG

permatex.JPG

What dealer did the original TSB for you?  I am also in Bucks County, and was thinking of taking it to Faulkner.  

Thanks in advance!

Posted
7 minutes ago, SPASierra said:

What dealer did the original TSB for you?  I am also in Bucks County, and was thinking of taking it to Faulkner.  

Thanks in advance!

I had the TSB done at O'Neil GMC in Warminster. They used an outside glass specialist and they did a good job. I can't even tell the truck had been touched. I bought this truck at O'Neil, and I'm very happy with how they've treated me - both in sales and service. I attribute the slight leak (after the TSB) to the crappy window frame design.  

Posted
1 minute ago, DSW1519 said:

I had the TSB done at O'Neil GMC in Warminster. They used an outside glass specialist and they did a good job. I can't even tell the truck had been touched. I bought this truck at O'Neil, and I'm very happy with how they've treated me - both in sales and service. I attribute the slight leak (after the TSB) to the crappy window frame design.  

Thanks for the quick reply!  I will give them a call!

 

Posted
Thanks for the quick reply!  I will give them a call!
 
No problem. Dave the service manager is a really good guy.

Sent from my Pixel 3a XL using Tapatalk

Posted

I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..

 

Posted
9 hours ago, Wormydog1724 said:

I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..

 

Hopefully you won't need to.

Posted
I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..
 
Washing doesn't usually have enough standing water to get the leak going like sitting in the rain. Wish you luck. So far my 2nd attempt, replaced whole window, has worked.
Posted

Add me to the list, 2020 AT4. Built Nov 2019 in mexico. 17,000 miles. Home garage, and work garage, and live in PHX, so not much water exposure. I'll probably wait a while to see if GM can come up with a good fix.1cb891b6f0ea35301c51b01c23234629.jpg7eebef29ea3335764b63e79080920844.jpg

Sent from my Pixel 5 using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • 2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...