Jump to content

The brake lights on my 2002 avalanche are not turning off

Whiteavy31097
 Share

Recommended Posts

Whiteavy31097 New Member

Whiteavy31097

Posted
Posted

I took a trip to Louisiana Sunday night and on the way back I noticed that my cruise control was not working when I stop to get gas I walk to the back of my truck and the brake lights are still on even with the key turned off my immediate thought was that the brake switch was bad After replacing it I found out that it was not the Brake switch  so my second thought was that maybe having recently have pulled a trailer that the trailer pin plug may have been shorted out I disconnected it and that was not the problem either I then began checking fuses all the fuses are good and even when I remove the brake light fuse the brake light still stay on the only way to get them to turn off Is to disconnect the battery I am at a loss of what it could be please help

Mikebtte Enthusiast

Mikebtte

Posted
Posted

Do the lights stay on with the key off? Normally the brake switch is the first place to start. As you replaced the switch did the lights turn off when unplugged? How are your brakes, could it be triggered by the pads being warn and needing replaced or a possible ABS issue.

rjgti Enthusiast

rjgti

Posted
Posted

the hot side of the brake circuit is getting 12v, most likely at the trailer plug, check wiring behind and leading the that plug

Whiteavy31097 New Member

Whiteavy31097

Posted
  • Author
Posted

 They do they even stay on when the fuse is pulled the only way to turn them off is to disconnect the battery the brake pads are good they were replaced about a month ago 

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • pyoung62
      2026 DENALI 6.2L

      By pyoung62 · Posted

      I agree with Tim.  As tech heavy as engines are these days, no way I’d be an early buyer of the new 6.6.  Of course, I bought my ‘26 Denali w/the 6.2 after dumping my Tundra with it’s defective 3.5 liter imploding engine disaster, so I’m a little gun-shy.  That said, my 6.2 has been rock solid.  I don’t drive it like I do my BMW Z4 M40i, but I don’t baby it either.  I got a V8 for a reason.  But I’m averaging 18 around town and 22 highway.  I have seen 24 highway as well when I wasn’t loaded up heavy.  Considering my Tundra with the twin turbo V6 only got 14.5 in town and 17 on the road, I’ll take the 6.2 all day, every day.  If I were you, I’d grab a ‘26 while you can.  Inventories are probably gonna start dropping and I’ll bet the deals will start looking sweeter as well.
    • ShowMeShooter1332
      Can you add a 360° Cameras hard button to a 2021 Sierra?

      By ShowMeShooter1332 · Posted

      I am curious if anyone has figured out a way to add an hard button AUX or 360 Camera switch to the center row of switches. I have a 2021 AT4, and want to split the hill decent button and add a 360 camera button so that you don't have to go into the center display and locate the camera functionality, etc...   My father's 2024 Yukon XL AT4 and it has a hard button, see below. I found this thread on the Yukons, but it seems like there may not be a part number for the 2021 sierras. https://www.gm-trucks.com/forums/topic/255339-adding-hard-button-for-camera-on-2021/ Anyone else figured this out. Seems like it would need to be a custom switch!   I am getting ready to install the auto stop/start eliminator, so would be nice to knock them out at once.     Upvote1Downvote0Go to comments
    • Grumpy Bear
      Winter Returned

      By Grumpy Bear · Posted

      Looks like the entire state is burning. 😬
    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...