Jump to content

Jingle jingle underneath only in 2wd

Limelight
 Share

Recommended Posts

  • Replies 1.3k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Limelight
Limelight

Dude the constant trolling is old. You sold your “Sad Chevy” so move on and enjoy your Ford. Really-  head on over to that Forum and enjoy your truck and let us enjoy ours. Every brand has proble

Thejet07
Thejet07

Truck is ready to be picked up. I will look to see the numbers on my axle and take a picture. Shocked they called me late today and not late tomorrow. Gm also called me yesterday wanting to talk about

ILSilverado
ILSilverado

So the Truck is back and so far no noise at all. Let's hope it stays that way. Will post updates .

Posted Images

316hepster Enthusiast

316hepster

Posted
Posted

I suppose there’s listed somewhere in this thread the parts needed to fix this. I fell asleep reading threads last night and only made it to page 15. Lol

  • 1 month later...
msaul37 Enthusiast

msaul37

Posted
Posted

almost beyond 36k miles and haven't taken the truck in yet for my own noise issue.

 

i'm 99.9% sure it's the same thing everyone else has had; driver's side stub shaft is loose compared to the passenger side, when in 2wd and ambient temperature is warmer than 65 degrees or so, it'll squeak, and when it's in auto or 4wd, it goes away and is silent.

 

anything i need to know to tell the dealer? specific bulletin or replacement part? 

316hepster Enthusiast

316hepster

Posted
Posted

Stupid question, I’m sure, but is this something the dealership would repair outside of the warranty?

RAYS B4U Enthusiast

RAYS B4U

Posted
Posted
6 hours ago, msaul37 said:

almost beyond 36k miles and haven't taken the truck in yet for my own noise issue.

 

i'm 99.9% sure it's the same thing everyone else has had; driver's side stub shaft is loose compared to the passenger side, when in 2wd and ambient temperature is warmer than 65 degrees or so, it'll squeak, and when it's in auto or 4wd, it goes away and is silent.

 

anything i need to know to tell the dealer? specific bulletin or replacement part? 

Here's a bulletin that might apply, PIP5653L Squeak Chirp noise from front axle in 2wd.

  • 2 weeks later...
Dhen-CHEV New Member

Dhen-CHEV

Posted
Posted

Well boys … I have a 2022 LT trail boss and experiencing the same issue as the previous 85 pages of this thread. I can feel the metal tick when driving at slower speeds through the parking lot. It almost sounds like a heart beat. Truck was repaired under the latest version of PIP5653 by replacing the stub shaft. I can say that the replacement did not fix the issue. I would really like some help with this. Attached is a video of me going about 10mph and you can hear the rotational “tick” noise. Let me know what y’all think. 
 

 

RAYS B4U Enthusiast

RAYS B4U

Posted
Posted
9 hours ago, Dhen-CHEV said:

Well boys … I have a 2022 LT trail boss and experiencing the same issue as the previous 85 pages of this thread. I can feel the metal tick when driving at slower speeds through the parking lot. It almost sounds like a heart beat. Truck was repaired under the latest version of PIP5653 by replacing the stub shaft. I can say that the replacement did not fix the issue. I would really like some help with this. Attached is a video of me going about 10mph and you can hear the rotational “tick” noise. Let me know what y’all think. 
 

 

That tic does not sound anything like the JingleJingle sound mine did, my guess is you have something else going on.

Silverado4x4 Senior Enthusiast

Silverado4x4

Posted
Posted (edited)

I agree that's not the same jingle issue noise others were hearing, you have something else going on. Really hard to get a good probability by a video.

Edited by Silverado4x4
Dhen-CHEV New Member

Dhen-CHEV

Posted
Posted
17 hours ago, Silverado4x4 said:

I agree that's not the same jingle issue noise others were hearing, you have something else going on. Really hard to get a good probability by a video.

Thanks for taking a look

Ross Kulma New Member

Ross Kulma

Posted
Posted (edited)

This is ILSilverado, OMG this thread has 85 pages and still going! Well GM eventually had to buy back my truck for the non fixable jingle. They ended up giving the truck to a College auto shop program. I now own a 2023 Silverado turbo.

Edited by Ross Kulma
GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted
On 1/14/2023 at 12:43 AM, Dhen-CHEV said:

Well boys … I have a 2022 LT trail boss and experiencing the same issue as the previous 85 pages of this thread. I can feel the metal tick when driving at slower speeds through the parking lot. It almost sounds like a heart beat. Truck was repaired under the latest version of PIP5653 by replacing the stub shaft. I can say that the replacement did not fix the issue. I would really like some help with this. Attached is a video of me going about 10mph and you can hear the rotational “tick” noise. Let me know what y’all think. 
 

 

This is certainly not what we like to hear, Dhen-CHEV.  Please know, customer satisfaction is extremely important to us. Our team would be more than happy to take a closer look into the concerns with your 2022 Chevrolet Silverado LT Trail Boss. To do so, please send an email to [email protected] with ATTN: Dhen-CHEV/GM Trucks in the subject line.

Please include your contact information, VIN, a brief description of your concern, and the name of your preferred dealership. We look forward to hearing from you. To learn more about GM’s Privacy Policy, please visit https://www.gm.com/privacy-statement.html. The information you provide may be monitored and recorded and is subject to the GM Privacy Statement.
 
Privacy Statement | General Motors
Your privacy is important to General Motors. This Privacy Statement addresses the personal information GM collects and how GM handles that personal information.
www.gm.com
 

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,775
    Total Members
    8,960
    Most Online
    sportfish17
    Newest Member
    sportfish17
    Joined

  • Who's Online   5 Members, 2 Anonymous, 2,009 Guests (See full list)

  • Latest Articles

  • Posts

    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That is a fair point, and I think an OBD-first proof is probably the right next step. I agree that the value is not the hardware box by itself. The marketable part would be the software: always-on capture, baseline learning, event reduction, system-specific reports, and alerts. Also agreed that if an OBD device is always plugged in and has local storage, it should not miss the event in the same way that a scanner plugged in after the fact would. The only thing I would not want to assume yet is that an ELM327-class device gives all the late-GM data needed at the rate needed. Standard OBD live data, DTCs, freeze frame, Mode 6, VIN, and calibration information are definitely the right starting point. GDS2 also proves that a lot of useful ECM data can be viewed through the DLC without needing a DTC first. The question I need to test is whether the data needed for a useful GM V8 event report is actually available through the DLC, and at a useful sample rate: - misfire counts / roughness by cylinder - AFM/DFM state - oil pressure and oil temperature - fuel trims - voltage / reset context - U-codes and communication events - calibration / software information - whether these are standard PIDs, enhanced DIDs, Mode 6 data, GDS2-only data, or not available So I think the right benchmark is: 1. Build the OBD-only version first. 2. Keep it plugged in and logging locally. 3. Compare it against GDS2 / freeze frame / HP Tuners or another higher-end logger. 4. Measure which parameters are available and at what update rate. 5. Only justify ECM-side hardware if it captures useful evidence the OBD version cannot. So you may be right: the consumer product might simply be an always-plugged-in OBD event recorder with much better reporting. A question for you: when you say ELM327 devices can already deliver all the data needed, do you mean generic OBD Mode 01 data only, or GM enhanced data as well? For a useful GM V8 report, would generic OBD data be enough, or would you expect the tool to include enhanced items like misfire by cylinder, AFM/DFM state, oil pressure/oil temp, U-codes, and calibration information?
    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I agree. 
    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...