Jump to content

Recommended Posts

Posted

Just got back from Les Schwab with  new wheels.

 

20x9 Fuel Hardline 0 Offset

Same tires 275/65/20

My lift is 1.5 inch all the way around

 

1307245725_fuelwheels19.thumb.jpg.439b034f2bb865f86d38252344170e86.jpg

Posted
On 11/9/2020 at 6:04 PM, Watkins4x said:

20x10 Hardrock Affliction-19

295/60r20 Toyo RT

2.5 Motofab front 2 spacer in back 

Removed bracket behind mud flap, and trimmed mud flap. 

7E830A96-E900-49B1-9553-43F0C5727D85.jpeg

How much do the tires stick out from the wheel well... can you post a pic from that angle? Did you have to trim anything?

Posted
1 hour ago, EricTheRed said:

How much do the tires stick out from the wheel well... can you post a pic from that angle? Did you have to trim anything?

They stick out a little.  I didn’t want the same stance as stock. 0 offset wouldn’t stick out as far as mine. I trimmed the mud flap and removed the bracket behind carpet. Very minor wouldn’t notice it unless you were looking for it. 

A5AAE07F-795C-4238-8C36-B7A9873D76D0.jpeg

  • Thanks 1
Posted

275/70R18 Milestar Patagonia.  33x11 mounted on the truck at 40 PSI.  Stock Suspension.

 

 

tires4.jpg

tires3.jpg

tires2.jpg

tires1.jpg

  • Like 1
Posted
On 11/11/2020 at 11:26 AM, Watkins4x said:

They stick out a little.  I didn’t want the same stance as stock. 0 offset wouldn’t stick out as far as mine. I trimmed the mud flap and removed the bracket behind carpet. Very minor wouldn’t notice it unless you were looking for it. 

A5AAE07F-795C-4238-8C36-B7A9873D76D0.jpeg

How do you like the RT's so far, I'm thinking of doing the same tire and size?

Posted
2 hours ago, CMillSilverado said:

How do you like the RT's so far, I'm thinking of doing the same tire and size?

I went with the Toyo RT because my tire guy quoted them really cheap. I think the Nitto Ridge Grappler is probably a better tire, but they $200 more. Neither one will ride as smooth as the stock tire because of the LT rating, but it’s not bad. Little stiffer ride, and a little road noise. 

Posted
285/55/22 nitro ridge grapplers. This is the exact look I was looking for. Traded in my 2019 4runner for this 2021 GMC Sierra Denali and really dig the 6.2! 
20201113_154329.thumb.jpg.f1aceacca654c760720734186bafe157.jpg
20201113_154316.thumb.jpg.92f867c1081043bba3d38ca3b8c81f22.jpg
This is the size tire I'm looking at doing when mine need replaced. Did you notice much difference in performance going to the heavier tire?

Sent from my SM-N960U using Tapatalk

Posted
24 minutes ago, JWOutdoors29 said:

This is the size tire I'm looking at doing when mine need replaced. Did you notice much difference in performance going to the heavier tire?

Sent from my SM-N960U using Tapatalk
 

I just got them today so I dunno? I'm sure I'm going to lose a cpl of mpg but it's ok, I have a daily driver for work, this truck is my weekender. I'll post up mpg after a a cpl of weeks. But I do love how they look, aggressive and mean.

Posted
On 10/14/2020 at 5:13 PM, Freddotron said:

2020 denali

2 inch level

22x10 -19

33 12.5 22 

No rub

Screenshot_20201014-181252_Gallery.jpg

What rims? Any rubbing? Did you do any trimming?

Posted
On 7/31/2019 at 8:32 AM, KEEPER OF SECRETS said:

Mine is a rwd Custom that came with 20x9 wheels and those tires.

 

The only thing I changed were the wheels, lug nuts and hub centric rings. 

Wheels came from Custom Wheel Offsets.

Offset might be the only thing to check out on yours, depending on tire choice. 

Maybe some other 4x4 owners will chime in with what will work, tire size and offset, w/o rubbing or other issues.

 

The main thing is this. Some wheels will require spacers, due to the redesigned front calipers having a molded in bump in the center, that require more inside contour of the rim to clear. TMK the previous Gen didn't have this bump. See attached photo.

These have plenty of clearance w/o spacers.

 

 

Caliper bump.jpg

Wonder if anyone has ever filed that bump down?

Posted
1 hour ago, 22’s said:

What rims? Any rubbing? Did you do any trimming?

Vision rocker wheels 22x10 -19

I have zero rub with a solid half inch of clearance at the worst of times

I removed the mudflap bracket and had to ummm.... "massage" an area of metal behind the mudflap and zip tie haha

These tires are a bit small for a 33x12.5x22 but I honestly think I could clear a 33x13.5 if there was such a thing availbile

Posted

Cali off-road 22x12 -51 offset 33x12 toyo open country m/t, 3/8 front spacer. Slight rub right before fulllock. I was thinking about 35s but a lot of cutting would’ve been required. 

96A2F288-3C08-4157-B9A0-6BFCE95B98FF.jpeg

Posted
On 9/15/2020 at 3:51 PM, MTindall said:

285/65/r20 NRGs

Stock wheels

No lift

 

119510270_10103094312465422_3186227812565143886_n.thumb.jpg.6b49c56a0bbba46dbac8788fea484910.jpg119601610_10103094326826642_2574998786700707022_n.thumb.jpg.d805cc000496c2e6926150f4a2ba2e06.jpg


so this is a stock AT4 1500 and you fit 285/65/20’s?  Any rub or trim?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I'm looking at carpal tunnel surgery on my left hand and lumbar fusion. 
    • While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.
    • Got this yesterday out of nowhere. Truck is a 25',6.6 gasser with 8k miles.  Only semi anomaly is that the truck had been sitting, uncranked for 6 days. Elec Stability Control showed immediately upon cranking, not while driving. No drivability issues, just the message. Battery didn't seem to be weak when cranking over.  I drove it, killed it, let it sit a few hrs with no avail.  Truck is 100% stock. No damage. 
    • This can be done.  It is not cheap and requires an instrument cluster swap with custom programming, new steering wheel with the controls on it, and a special jumper harness.   The cluster upgrade - 12.3” Digital Cluster Upgrade – 2022.5–2026 Silverado / Sierra (T1 Refresh Pickup) - WAMS   The wheel upgrade - Steering Wheel Upgrade Kit – 2022.5–2026 Silverado / Sierra (T1 Refresh Pickup) - WAMS   The column harness upgrade - 2019 - 2026 Silverado / Sierra: Steering Wheel LIN Bus Harness - Harness Dr. - DIY Done Right     The problem with doing all of this?  You pretty much can't have any programming done to your truck that involves the cluster ever again.  The dealer won't be able to program the cluster as GM's system will only pull data for the cluster the truck came with.  So it would be advised also to turn off over the air updates.   TLDR;  Should have bought an LT double cab?  You'd have a power seat, the wheel controls, the cluster, all things that you've been seeking in your various posts so far about your new WT regular cab.  
    • I was unaware of that, thanks for updating me.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...