Jump to content

Block Heater

railguy777
 Share

Recommended Posts

railguy777 Enthusiast

railguy777

Posted
Posted

My truck came with a block heater. It was -20 last night here in Ottawa and no more than -15 today so I thought I would plug in the block heater and see how it worked.

I plugged in the heater cord that came with the truck and checked the voltage =120 v. Was curious about how much draw there is but my amp probe  showed zero amps

when plugged in. I checked the continuity of the cord, all good. I checked the resistance of the heater at the plug on the truck , it shows open circuit. 

I read on other posts about block heaters that the thermostat is in the cord itself. It appears that GM has moved the thermostat into the heater itself on the new models so that

the cord cannot be tampered with. For me I would just like the heater to work when I want it to, not when GM feels its necessary, I think -15 is cold enough to warrant

use of the heater. Attached are pics of the cord  that came with the truck -2020 Sierra SLT

 
  •  

IMG_0541.jpg

IMG_0540.jpg

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

YYC-SIERRA
YYC-SIERRA

Two months ago, I cut a 2" hole in my splash guard under the truck and installed a "NOCO Splitter GCP2 15 Amp 125V AC Port Plug"    The NOCO splitter has two 18" extension cords.   

jmer98
jmer98

Hey Guys Question I have a 2021 1500 3.0 While driving normal not towing my coolant temp sits about 210 slightly and tends to fluctuate up and down from 210 to about 225. Is this normal I have only 6

YYC-SIERRA
YYC-SIERRA

More pix.   I've driven in a lot of snow, slush, mud, etc. Both the splash guard and the yellow 3-way under the bumper stay 95% clean and dry, no issues. The NOCO plug has a nice soft rubber

Posted Images

redwngr Senior Enthusiast

redwngr

Posted
Posted

You have a 3.0L (that includes the block heater) or an optional factory block heater on a gasser?

 

Ottawa area, so  working in *C and it was  -20*C (-4*F)  ?

 

Was it -20*C when you started it?

How did it start?  

 

Mine hasn't seen temps that low yet. 

 

 

Salsa De Piña Enthusiast

Salsa De Piña

Posted
Posted

On my 2019 LD, the thermostat is further up the cord, under the hood near the fuse block.  Can you chase where the wiring goes in the engine compartment from the outlet in the bumper?  Be forewarned that bypassing the thermostat will most likely result in a CEL as there will be a discrepancy between engine sensors on startup.  That's why the thermostat was included in the first place.

 

The bumper plug is probably the biggest feature I'm envious about regarding the T1 because it's a clean look, except I'm concerned it would freeze with road spray or leaving a car wash.

AlaskaErik Enthusiast

AlaskaErik

Posted
Posted
1 hour ago, Salsa De Piña said:

The bumper plug is probably the biggest feature I'm envious about regarding the T1 because it's a clean look, except I'm concerned it would freeze with road spray or leaving a car wash.

Mine gets all covered up when it's snowing.  It should have been placed much higher up to keep as much snow and road spray out of it as possible and to make it easier to reach.

jmer98 Enthusiast

jmer98

Posted
Posted

Hey Guys Question
I have a 2021 1500 3.0
While driving normal not towing my coolant temp sits about 210 slightly and tends to fluctuate up and down from 210 to about 225. Is this normal I have only 675 mi and has done this from the first drive.
Thanks

Sent from my SM-G986U using Tapatalk

  • Like 1
Grover67 Enthusiast

Grover67

Posted
Posted

Yep normal temps, it'll steady out more you drive it and temps stabilize. There is alot going on and if you get a chance read up on it on why there is fluctuations on how the cooling system works

 

-Grover67

jmer98 Enthusiast

jmer98

Posted
Posted
Yep normal temps, it'll steady out more you drive it and temps stabilize. There is alot going on and if you get a chance read up on it on why there is fluctuations on how the cooling system works
 
-Grover67
Where can I find that information?

Sent from my SM-G986U using Tapatalk

BigMick2023 Enthusiast

BigMick2023

Posted
Posted

My 2020 RST CC has the block heater as an option, have not used it yet. 

Will have to give it a try to see if mine does the same. 

 

Is a slick setup with the plug port in front though, just need tp keep the connection cord they provide in a easy to find spot!  

railguy777 Enthusiast

railguy777

Posted
  • Author
Posted
17 hours ago, redwngr said:

You have a 3.0L (that includes the block heater) or an optional factory block heater on a gasser?

 

Ottawa area, so  working in *C and it was  -20*C (-4*F)  ?

 

Was it -20*C when you started it?

How did it start?  

 

Mine hasn't seen temps that low yet. 

 

 

 

railguy777 Enthusiast

railguy777

Posted
  • Author
Posted

I have the 5.3 .It started ok in that weather just wish I could warm it up before. 

I don't like not having the option

YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted (edited)

Two months ago, I cut a 2" hole in my splash guard under the truck and installed a "NOCO Splitter GCP2 15 Amp 125V AC Port Plug" 

 

The NOCO splitter has two 18" extension cords. 

 

I then bought a quality 3 way outlet (yellow) and secured it up under the bumper, inserted it into one of the NOCO cords.

 

I installed an 125w Temro heat pad to the oil pan (with build in thermostat), as well as a 100w Besco/Alaska heat pad transmission pan. Also installed a 75w Kats battery blanket. Plugged the 3 of those into the yellow triple outlet. The oil pan heater was a pain because of the grooves in the oil pan, I had to get a narrow 1.5" x 3" pad that just barely fit the confines of the flat section of the oil pan without grooves. Applied a liberal amount of silicone to both pads after installation.

 

Plugged the factory block heater into the other NOCO extension cord. 

 

So now when I plug my cord from the house into the splash guard, it powers all 4 heaters. The combined wattage does not exceed or trip the 15amp breaker. Slight nuisance to have to get down on 1 knee to plug it in, but everything seems to work great after 2 months.

 

 

 

 

20201022_153748.jpg

20201022_154525.jpg

20201022_154546.jpg

20201022_154606.jpg

20201022_161701.jpg

20201022_190132.jpg

20201022_190140.jpg

20201022_191055.jpg

Edited by YYC-SIERRA
  • Like 1
  • Thanks 1
YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted (edited)

More pix.

 

I've driven in a lot of snow, slush, mud, etc. Both the splash guard and the yellow 3-way under the bumper stay 95% clean and dry, no issues. The NOCO plug has a nice soft rubber plug seal that helps keep any moisture and debris out when driving. 

 

It's clean and hidden. When I change my oil, after I remove the bolts to lower the splash guard, I just reach up and disconnect the 2 NOCO plugs then the whole thing is removed as normal for each oil change.

 

After a few hours plugged in, I find it raises the temperature on my transmission by approx 10 degrees Celsius. I can only assume the oil pan heater is similar. It definitely starts easier when it's -15 out.

 

20201022_202558.jpg

20201218_075459.jpg

20201218_075511.jpg

20201218_075528.jpg

Edited by YYC-SIERRA
  • Thanks 1
YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted
18 hours ago, railguy777 said:

My truck came with a block heater. It was -20 last night here in Ottawa and no more than -15 today so I thought I would plug in the block heater and see how it worked.

 

  •  

 

Sorry, forgot the whole reason I came to this thread.

 

When I did the above installation, I noticed on the cord, hidden away, is a tag attached to it. Says something like "-17 or below" for operation.

 

I agree with you, I wish it would activate when I choose to plug it in, not when GM decides. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Zane
      2027 GMC Sierra: Official Discussion

      By Zane · Posted

      Not sure about DFM tech but i know there's a stop/start deactivation button. 
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      I could be interested if they axed cylinder deactivation and at least have a button for stop start. I’m sure the HP numbers will be higher. I would want a longer warranty to help build confidence. I’m a less is more guy as I get older. A V-8 work truck model would be my choice. I know a few outfitters for custom additions I prefer. 
    • Zane
      2027 GMC Sierra: Official Discussion

      By Zane · Posted

      It's official. GMC pulled the covers off the next-gen 2027 Sierra 1500, and we got the first official look. Full breakdown here: https://www.gm-trucks.com/next-gen-2027-gmc-sierra-1500-v8-trim-changes/   The quick hits: SLE and SLT are dead. The new core retail trim is just called "Elevation". Two new V8s, a 5.7L and a 6.6L built with high-performance Corvette architecture roots. No horsepower or torque numbers yet. The 2.7 TurboMax finally ditches the old gearbox and gets the 10-speed automatic. AT4X moves to larger standard 35-inch tires with front and rear e-lockers, Multimatic DSSV dampers, and heavy-duty Jounce Control Dampers. Over 60 inches of combined display on Denali Ultimate and AT4X, complete with a motorized articulating center screen and an adaptive passenger screen. Seven simplified trims across the entire model line to clean up ordering confusion.   So let's get into it: New 5.7L and 6.6L gas V8s with custom active exhaust tuning and a Corvette connection. Is this the exact engine lineup half-ton traditionalists have been begging for? Purging the iconic SLE and SLT names after all these years to lean entirely on Elevation as the high-volume core. Bold move, or a mistake? That motorized articulating 16.3-inch screen that slides up to reveal a hidden dashboard vault. Awesome mechanical theater, or does it make you nervous about long-term durability? Physically lowering the headlamps in the front fascia to improve road courtesy and stop blinding oncoming traffic. Smart real-world engineering, or does it hurt the truck's aggressive stance? What trim are you putting your name down for on day one? Drop your first impressions below.  
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      My overnight hospital stay turned into five.  I developed a post operative fever and an erratic  heart rate.  A blood clot in the lungs was the culprit.  This is apparently a common post surgical complication and easily remedied.   I was the youngest in a four bed ward and a Doctor with a Geriatric specialization was in charge of my care.  All of the nurses were good and some were outstanding at dealing with old people.  It was very evident that my age triggered a different level of care!  My advice to any senior going for a hospital stay is to have a trusted family member advocate visible.  If not, you will still be well cared for, but you may discover that your voice  isn't as strong as it once was! 
    • diyer2
      Gas Prices

      By diyer2 · Posted

      $4.25 85 oct. in town, down 50 cents.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...