Jump to content

Block Heater

railguy777
 Share

Recommended Posts

railguy777 Enthusiast

railguy777

Posted
Posted

My truck came with a block heater. It was -20 last night here in Ottawa and no more than -15 today so I thought I would plug in the block heater and see how it worked.

I plugged in the heater cord that came with the truck and checked the voltage =120 v. Was curious about how much draw there is but my amp probe  showed zero amps

when plugged in. I checked the continuity of the cord, all good. I checked the resistance of the heater at the plug on the truck , it shows open circuit. 

I read on other posts about block heaters that the thermostat is in the cord itself. It appears that GM has moved the thermostat into the heater itself on the new models so that

the cord cannot be tampered with. For me I would just like the heater to work when I want it to, not when GM feels its necessary, I think -15 is cold enough to warrant

use of the heater. Attached are pics of the cord  that came with the truck -2020 Sierra SLT

 
  •  

IMG_0541.jpg

IMG_0540.jpg

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

YYC-SIERRA
YYC-SIERRA

Two months ago, I cut a 2" hole in my splash guard under the truck and installed a "NOCO Splitter GCP2 15 Amp 125V AC Port Plug"    The NOCO splitter has two 18" extension cords.   

jmer98
jmer98

Hey Guys Question I have a 2021 1500 3.0 While driving normal not towing my coolant temp sits about 210 slightly and tends to fluctuate up and down from 210 to about 225. Is this normal I have only 6

YYC-SIERRA
YYC-SIERRA

More pix.   I've driven in a lot of snow, slush, mud, etc. Both the splash guard and the yellow 3-way under the bumper stay 95% clean and dry, no issues. The NOCO plug has a nice soft rubber

Posted Images

redwngr Senior Enthusiast

redwngr

Posted
Posted

You have a 3.0L (that includes the block heater) or an optional factory block heater on a gasser?

 

Ottawa area, so  working in *C and it was  -20*C (-4*F)  ?

 

Was it -20*C when you started it?

How did it start?  

 

Mine hasn't seen temps that low yet. 

 

 

Salsa De Piña Enthusiast

Salsa De Piña

Posted
Posted

On my 2019 LD, the thermostat is further up the cord, under the hood near the fuse block.  Can you chase where the wiring goes in the engine compartment from the outlet in the bumper?  Be forewarned that bypassing the thermostat will most likely result in a CEL as there will be a discrepancy between engine sensors on startup.  That's why the thermostat was included in the first place.

 

The bumper plug is probably the biggest feature I'm envious about regarding the T1 because it's a clean look, except I'm concerned it would freeze with road spray or leaving a car wash.

AlaskaErik Enthusiast

AlaskaErik

Posted
Posted
1 hour ago, Salsa De Piña said:

The bumper plug is probably the biggest feature I'm envious about regarding the T1 because it's a clean look, except I'm concerned it would freeze with road spray or leaving a car wash.

Mine gets all covered up when it's snowing.  It should have been placed much higher up to keep as much snow and road spray out of it as possible and to make it easier to reach.

jmer98 Enthusiast

jmer98

Posted
Posted

Hey Guys Question
I have a 2021 1500 3.0
While driving normal not towing my coolant temp sits about 210 slightly and tends to fluctuate up and down from 210 to about 225. Is this normal I have only 675 mi and has done this from the first drive.
Thanks

Sent from my SM-G986U using Tapatalk

  • Like 1
Grover67 Enthusiast

Grover67

Posted
Posted

Yep normal temps, it'll steady out more you drive it and temps stabilize. There is alot going on and if you get a chance read up on it on why there is fluctuations on how the cooling system works

 

-Grover67

jmer98 Enthusiast

jmer98

Posted
Posted
Yep normal temps, it'll steady out more you drive it and temps stabilize. There is alot going on and if you get a chance read up on it on why there is fluctuations on how the cooling system works
 
-Grover67
Where can I find that information?

Sent from my SM-G986U using Tapatalk

BigMick2023 Enthusiast

BigMick2023

Posted
Posted

My 2020 RST CC has the block heater as an option, have not used it yet. 

Will have to give it a try to see if mine does the same. 

 

Is a slick setup with the plug port in front though, just need tp keep the connection cord they provide in a easy to find spot!  

railguy777 Enthusiast

railguy777

Posted
  • Author
Posted
17 hours ago, redwngr said:

You have a 3.0L (that includes the block heater) or an optional factory block heater on a gasser?

 

Ottawa area, so  working in *C and it was  -20*C (-4*F)  ?

 

Was it -20*C when you started it?

How did it start?  

 

Mine hasn't seen temps that low yet. 

 

 

 

railguy777 Enthusiast

railguy777

Posted
  • Author
Posted

I have the 5.3 .It started ok in that weather just wish I could warm it up before. 

I don't like not having the option

YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted (edited)

Two months ago, I cut a 2" hole in my splash guard under the truck and installed a "NOCO Splitter GCP2 15 Amp 125V AC Port Plug" 

 

The NOCO splitter has two 18" extension cords. 

 

I then bought a quality 3 way outlet (yellow) and secured it up under the bumper, inserted it into one of the NOCO cords.

 

I installed an 125w Temro heat pad to the oil pan (with build in thermostat), as well as a 100w Besco/Alaska heat pad transmission pan. Also installed a 75w Kats battery blanket. Plugged the 3 of those into the yellow triple outlet. The oil pan heater was a pain because of the grooves in the oil pan, I had to get a narrow 1.5" x 3" pad that just barely fit the confines of the flat section of the oil pan without grooves. Applied a liberal amount of silicone to both pads after installation.

 

Plugged the factory block heater into the other NOCO extension cord. 

 

So now when I plug my cord from the house into the splash guard, it powers all 4 heaters. The combined wattage does not exceed or trip the 15amp breaker. Slight nuisance to have to get down on 1 knee to plug it in, but everything seems to work great after 2 months.

 

 

 

 

20201022_153748.jpg

20201022_154525.jpg

20201022_154546.jpg

20201022_154606.jpg

20201022_161701.jpg

20201022_190132.jpg

20201022_190140.jpg

20201022_191055.jpg

Edited by YYC-SIERRA
  • Like 1
  • Thanks 1
YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted (edited)

More pix.

 

I've driven in a lot of snow, slush, mud, etc. Both the splash guard and the yellow 3-way under the bumper stay 95% clean and dry, no issues. The NOCO plug has a nice soft rubber plug seal that helps keep any moisture and debris out when driving. 

 

It's clean and hidden. When I change my oil, after I remove the bolts to lower the splash guard, I just reach up and disconnect the 2 NOCO plugs then the whole thing is removed as normal for each oil change.

 

After a few hours plugged in, I find it raises the temperature on my transmission by approx 10 degrees Celsius. I can only assume the oil pan heater is similar. It definitely starts easier when it's -15 out.

 

20201022_202558.jpg

20201218_075459.jpg

20201218_075511.jpg

20201218_075528.jpg

Edited by YYC-SIERRA
  • Thanks 1
YYC-SIERRA Enthusiast

YYC-SIERRA

Posted
Posted
18 hours ago, railguy777 said:

My truck came with a block heater. It was -20 last night here in Ottawa and no more than -15 today so I thought I would plug in the block heater and see how it worked.

 

  •  

 

Sorry, forgot the whole reason I came to this thread.

 

When I did the above installation, I noticed on the cord, hidden away, is a tag attached to it. Says something like "-17 or below" for operation.

 

I agree with you, I wish it would activate when I choose to plug it in, not when GM decides. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      You must have that upgraded gvw package which is only available or at least was in 2025 with the diesel engine for the 3/4 ton and that gave the truck physically the larger 12.0 ring gear rear diff and the 3500 rear spring pack. There is a difference in what the diff housing looks like externally as one tell tale and also your truck should have the upper overload spring pack and the frame pads that the pack goes up against.    The pressure the tpms system kicks the alarm in on a stock setting truck, that is a good question and was just from what I recall but I doubt I made any notes on it as I knew for the rear that it was not at all what I was after regardless either. Being that you have a diesel and if running on stock tires the minimum pressure on an empty truck seems to be around 50 psi from hearing of those that have weighted the front axle but the rear axle is very similar in weight to a gas truck and again a near empty truck on the rear could go down to 35 pounds at minimum. However the weigh scale is the proper way to know for sure as a guide.    As to changing the readings on the dash from metric to the US measuring system, oh yes that is done easily but what I was attempting to explain was that I can't pick and choose items I want to have in US and those I still want in the metric system at the same time as its either all or none. For example lets say you drove into Canada and switched your dash over to metric so your speedometer read in km an hour, well then your reading kilopascals on your tpms readout and your wife looks over and says what the hell is that saying in the tpms screen and you say "darned if I know, I think its Chinese" !
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      This is partly why I decided to have switched over to Amsoil SS as a way of hopefully preventing the buildup of the sludge/carbon on the pistons and clogging of the oil control rings and the carbon that would cause the compression rings to stick in their grooves as well as stay cleaner up top of the heads in the valve train in the first place, an oil that has tested better by third party testing over typical shelf oil and also doing my best to run relatively short OCI. However in saying that I don't think there is any way to easily prove the oil I was using prior allowed for a buildup at the OCI I was doing, nor in the other direction to make claims the Amsoil is keeping everything clean either. There really isn't a window into the engine is there to know anything for certain even if oil samples were taken for example that showed still healthy oil being dropped out of the oil pan other than engine tear downs that extensive and expensive testing of oils does to actually visually see what is really going on inside the engine. I wish there was some easy method of seeing what is going on but I don't happen to be aware of that if there is.  
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      My truck is a ¾ ton but my placard also says 80 for the rear tires, I think I might have the upgraded suspension to the 3500 series maybe.   I put my air down to 60 and the light was still on, and there was no way I was putting over 60 psi in the rear empty and not towing because I knew the actual number Toyo gave me and I didn't wanna ruin the center of my tires!   And you actually can change it in the settings from metric or is and it will show kph or mph then when you go into your tire settings it will be either psi or kpa, but it would be nice to just change it directly on the tire psi page 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...