Jump to content

Recommended Posts

Posted (edited)

Installed. 2" RC level kit today. All I did was disconnect the bottom of the strut and loosened the ball joint and I was able to slide the level blocks in at the bottom. Took me 35 minutes a side. Anyone else install them like this vs taking everything apart?

Man I wish mine went that easy today. I could not get the upper ball joint free on the passenger side. Hammered the hell out of it and even tried a ball joint release tool (pickle fork) but never got it free. Brand new truck and I hated hammering on it like that too. Ended up putting it back together. Any ideas out there??

Edited by '17 Sierra
Posted

Man I wish mine went that easy today. I could not get the upper ball joint free on the passenger side. Hammered the hell out of it and even tried a ball joint realize tool (pickle fork) but never got it free. Ended up putting it back together. Brand new truck and I hated hammering on it like that too. Ended up putting it back together. Any ideas out there??

Mine is a 2015 with 9k miles on it. 4 good hits with a 5lb hammer and it popped out. I didn't take the nut all the way off.

Posted

Mine is a 2015 with 9k miles on it. 4 good hits with a 5lb hammer and it popped out. I didn't take the nut all the way off.

Tie rod popped right off and probably didn't even need it off. I also used a 5lb hammer on the ball joint knuckle. I figured being so new it would have come right off.

Posted

Tie rod popped right off and probably didn't even need it off. I also used a 5lb hammer on the ball joint knuckle. I figured being so new it would have come right off.

Whack that sucker..lol I hit it twice on each side and it popped out.

Posted

Whack that sucker..lol I hit it twice on each side and it popped out.

Oh I whacked it good....believe me. Weird.

Posted (edited)

Stock suspension with stock 275/55r20 Wranger SRA's:

20170105_125041_zpslkjbera4.jpg

 

2" level in front with 275/60r20 Falken AT3W's

20170118_161905_zpsubimaifw.jpg

Edited by evilstevie
  • Like 1
Posted

Man I wish mine went that easy today. I could not get the upper ball joint free on the passenger side. Hammered the hell out of it and even tried a ball joint release tool (pickle fork) but never got it free. Brand new truck and I hated hammering on it like that too. Ended up putting it back together. Any ideas out there??

My '16 passenger side was very stubborn as well, almost to the point of giving up. A 5lb hammer worked, but had to alternate hitting the knuckle from the the front and back. After about a dozen hits, it came loose. Driver side popped right out.

  • Like 1
Posted (edited)

I have the Rough Country 2 inch level kit that will be installed sometime in a few weeks. My truck is a regular cab with 17 inch wheels and Dueler 265/70 a/t tires. I don't plan on getting any bigger tires anytime soon. Ill post pics when installed.

Edited by Geiser100
Posted

Getting my 33" tires installed tomorrow. Will try and remember to take before and after pics.

Posted

Thanks for advice. Got it done tonight...now gotta adjust the headlights and alignment.

Posted

Thanks for advice. Got it done tonight...now gotta adjust the headlights and alignment.

I have to figure out how to adjust the headlights now.

 

Getting my 33" tires installed tomorrow. Will try and remember to take before and after pics.

Forgot to take before and after pics but I'll post tomorrow. It's dark out. Tires are a bit noisy so I'm hoping they wear down a bit and quiet down. No rubbing of any kind and it looks awesome.

  • Like 1
Posted

I installed front and back today, I think my alignment shop screwed me over,, they charged me an extra half hour labor to sync the steering angle,, sounds like a bunch of bs

Posted

I have to figure out how to adjust the headlights now.

 

 

Forgot to take before and after pics but I'll post tomorrow. It's dark out. Tires are a bit noisy so I'm hoping they wear down a bit and quiet down. No rubbing of any kind and it looks awesome.

My Federal make some noise which I initially thought it was a bit to much then I either got used to it or they wore out a bit; but the noise sounds lower and no longer bothers me. Also i increased the psi from 35 to 47lbs to help diminish noise and have less roll resistance.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

My Federal make some noise which I initially thought it was a bit to much then I either got used to it or they wore out a bit; but the noise sounds lower and no longer bothers me. Also i increased the psi from 35 to 47lbs to help diminish noise and have less roll resistance.

Sent from my iPhone using Tapatalk

They put mine to the stock pressure so l'll adjust mine today and see if there's a difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Well one of our most reliable vehicles was sold yesterday. The first and only I gave for free to a grandkid. If they got skin in the game they take care of it. My wife bought new. Five years later my daughter got it to use. We got it back and gave it to our grandson after graduation. He did zero maintenance just oil changes. When the AC quit he drove his mother’s car rather than get it fixed. Instead he just bought a beater and sold the Elantra. 
    • I usually do as well or better than the sticker for mileage. Usually better going west than east. North then South. Wind makes a difference. I’m not usually a conspiracy theorist. But it did dawn on me I’m going by the vehicle calculation. Now that would be interesting.
    • https://www.msn.com/en-us/autos/news/fuel-economy-stickers-don-t-tell-the-whole-story-aaa-data-reveals-why/ar-AA26ocHk?ocid=winp2fptaskbarhover&cvid=6a4122ea3dae47e5b8dfbed5d4fd3d55&cvpid=648f6b4fc2fa4eddb4c12893aeb957ed&ei=59
    • What’s missing in all this is patience and investment in the future. Buy a 170K starter home. Ten years later sell it invest in a more expensive home. Eventually you’ll have a 600K home and pay starter home payments. Buy a starter car. Maintain it well. Save the payments after it’s payed for then buy an expensive car if you desire. Buy a tumbler make your own coffee, pack your lunch. Cook your own dinner. Most importantly take care of your car.
    • People mislead themselves. Statistics are highly useful indicators.   Here's the tie-in to this thread. If an oil sample tests shows a wear indicator of 7 using cheaper ACDelco oil, and a wear indicator of 2 (lower = less wear) using a particular brand of Mobil oil, and wear has a linear relationship with engine lifespan, anyone could assume that Mobil is reducing wear by more than 50% (let's just say a 200% reduction for you red state people trying hard to do math) which leads to increasing engine life by 2x. Perhaps, in a vacuum, by itself, when dreamed by AI.   Yeah?! That's what the statistic is saying, isn't it?   No, it isn't. It didn't come out and say engine life is doubled. That's a very bad assumption, and a case of severe myopia by assuming something potentially untrue about the only data point in focus.   Average cost of a new car is 50k. You bet it is.   The median cost of a new car is more like 35k. Expensive cars are skewing the perception that "average" now means a $50k price of entry for a very average automobile. And that's not true. People who don't understand statistics twist the living heck out of them to mean all sorts of things they don't actually mean.   "Average" new car payment is $1000/month. Yep, it is. And in that number are all the $35k new car buyers who bring significant equity, and the $25k new car buyers who finance the car for a month just to get a rebate, and then pay it off. Know what isn't in that number? All the payments made by people who don't finance a car.   Picking one's own data point (don't have a car payment, never paid $50k for a new vehicle, my house cost $170k, I afforded a middle class lifestyle on $4.50/hr) is just a data point. Just like earning $25/hr in an area where the median home price is almost $1 Million is a data point. In fact, it's a lot of data points given that 80% of the US population lives in/around major cities. They're not idiots; the vast majority of them do it to make a living because that's where the big money is.   The highs have become higher, lows have become lower, and how your personal mileage varies is not truth for an entire country. At the same time you can't NOT acknowledge the data. While it doesn't paint YOUR personal picture, it certainly tints the reality that you also live in, as does your single data point.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...