Jump to content

Recommended Posts

Posted (edited)

Got around to pulling all the parts out to make sure I have everything. The engine should be out tomorrow and hopefully new parts will start going in. 
 
quick parts list 

-L86 manifold with additional port injections. (will be installed with 50lbs injectors but won’t be hooked up just yet)

- 2000cc meth injection 

- Borg S476 with billet wheel

- Cam Motion turbo cam

- BTR .660 dual valve spring

- Johnson 2110R lifters

- CHE trunnions

- Turbo Smart WG / BOV

- ARP head and main studs

- L86 OEM crank

- GPI “drop in” pistons and rods

- OEM head gaskets 

- custom Garrett core intercooler

- Derale trans cooler (will be under the bed). Removing the 40k Trucool from up front. 
And a bunch of other little stuff. 

ECE1CC3F-86B2-4F0D-AF5F-0003449A5459.jpeg

Edited by CajunFries
  • Like 4
Posted (edited)

1500 PAGES?!!!!!  HOLY CRAP!!!!

 

Drove my truck for the first time in 10 days, $8/gal sucks, been driving my son's car or my wife's CR-V Hybrid, and driving my truck once every week or two.  As I was driving down the main drag in town, I heard something flopping in the breeze under my (open) sunroof.  I usually drive for about 10 minutes or miles with the sunroof in vent and shade almost closed, to draw the heat out.

 

1320097648_SunroofRTside.thumb.jpg.4356cb6eecb0312032a858694a05da7c.jpg

 

Found it to be a VERY simple fix.  Just re-engage the clip/slot from the front to the back.

352685560_SunroofRTsidefixed.thumb.jpg.3c08fc168e6981e4b9a488e7ff296f45.jpg

Edited by Ravenkeeper
  • Like 2
Posted
6 hours ago, Ravenkeeper said:

1500 PAGES?!!!!!  HOLY CRAP!!!!

 

Drove my truck for the first time in 10 days, $8/gal sucks, been driving my son's car or my wife's CR-V Hybrid, and driving my truck once every week or two.  As I was driving down the main drag in town, I heard something flopping in the breeze under my (open) sunroof.  I usually drive for about 10 minutes or miles with the sunroof in vent and shade almost closed, to draw the heat out.

 

1320097648_SunroofRTside.thumb.jpg.4356cb6eecb0312032a858694a05da7c.jpg

 

Found it to be a VERY simple fix.  Just re-engage the clip/slot from the front to the back.

352685560_SunroofRTsidefixed.thumb.jpg.3c08fc168e6981e4b9a488e7ff296f45.jpg

$8/gal?!?!? Where are you at?!???

Posted

I removed the plastic fender pieces and pulled the wheel well insert. Gave everything a good cleaning, then re-installed.

 

Super easy to do, don't need to remove the wheel. Just a T15 bit and a phillips screwdriver.

dirty1.jpg

pieces.jpg

dirty3.jpg

clean1.jpg

clean2.jpg

  • Like 2
Posted

finally received the builtright bedside rack, I'm 2 days into a rather mean cold that has me wore out, I will try and piece it together in the next couple days

  • Like 1
Posted
On 6/3/2022 at 9:32 PM, CajunFries said:

$8/gal?!?!? Where are you at?!???

Ok, I exaggerated a little bit.  Average price around Antelope Valley (Lancaster/Palmdale) is $6.75

Posted
9 hours ago, Ravenkeeper said:

Ok, I exaggerated a little bit.  Average price around Antelope Valley (Lancaster/Palmdale) is $6.75

Ahhh gotcha. I havnt been out there in a while. Used to ride at willow spring all the time. 

  • Like 1
Posted

10ft of heat sleeve for the AC lines and couple of wires and Heat shield for the battery trying to protect it from the heat from the turbo. 35D83E49-FC03-403F-81B9-2F4ED8B52782.thumb.jpeg.9b3e265033247dd0d6266fe5eac62bb3.jpeg

  • Like 2
Posted
On 6/7/2022 at 4:30 PM, YYC-SIERRA said:

I removed the plastic fender pieces and pulled the wheel well insert. Gave everything a good cleaning, then re-installed.

 

Super easy to do, don't need to remove the wheel. Just a T15 bit and a phillips screwdriver.

dirty1.jpg

pieces.jpg

dirty3.jpg

clean1.jpg

clean2.jpg

I am definately going to do this for my 18.

  • Like 1
Posted

Finally got a chance to test out my new electric pressure washer and foam cannon. Was too into the wash I forgot to take a picture of it all foamed up. Clayed/waxed after the hard winter neglect, full interior detail as well. Much needed!

 

Next week going to drop the trans pan and change filter/oil. 48k since the last time it's been changed and shifts are starting to firm up more than I'd like. Hoping to get as much life out of this 6 speed before I start getting the itch for a new AT4...

 

598601016_IMG_0021(1).thumb.jpg.45bdddc64ca36330457cbfabbf4e78c1.jpg

IMG_0025.thumb.jpg.bcafcd41371fdc1bed9936b446c3f057.jpg

  • Like 5
Posted

What have I done for my K2 today. Well great question. I ended up finding a torn CV boot. Now researching my options. 

  • Like 1
  • Sad 1
Posted (edited)

Insulated the doors with ccf and ccf/al. Sounds better for sure. Now to chase down a door panel rattle. 

20220618_164552.jpg

20220618_161516.jpg

Edited by Snowcamo
  • Like 5
Posted

finally got around to getting the builtright bedside rack system together.

comes with absolutely ZERO instructions, not a big deal but assembling some of the quickgrip stuff it would be nice to have a general idea of how it is supposed to be, there website has some install guides but none for chevy 

I have a bedliner installed so it has complicated things a little bit, the bottom attachment is not ideal it is a U shaped bracket but should be a u-bolt or a j bolt or at least have a L leg so you can turn it and snug it up that way, the way it is it now it just binds up so I bought some longer bolts and sleeves at the hardware and will finish it up in the morning.  I may end getting a u-bolt and drilling a couple holes in the rack I could not find one that would fit the existing holes

PXL_20220617_225438981.jpg

  • Like 6
Posted
On 6/18/2022 at 4:16 PM, maillet282 said:

What have I done for my K2 today. Well great question. I ended up finding a torn CV boot. Now researching my options. 

Had my passenger side rip late last year. Easiest and quickest option IMO... replace it. Took me about an hour, worst part is getting the dang thing out! Ended up having to remove the bottom 2 strut bolts, and sway bar end link which gives you some additional room with the lower control arm dropped.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • So speaking of oil consumption with my L8T as I just changed the oil yesterday and made the switch over to Amsoil SS 0W-40 from the Mobil 1  5W-30 Truck and SUV I just dropped out. 2900 miles on that oil as well as  68 hours on that oil ( so used to equipment with an hour meter and that becomes valuable information to compare with others as well ). Once again the oil use was so very little, I am going to say it dropped under 1/16 of an inch on the dipstick. No towing was done and this interval was from early spring until now.    One interesting item to note is that going by the 5 quart jugs I was using before from Mobil, it was showing that I was putting in 8 US quarts to bring it to full if not slightly over the full mark according to their jug markings. Granted I did allow more drain time this time and in part because the engine oil was only lukewarm as I started it and let it idle and not for long enough to get the oil itself hot ( the engine was up to operating temp ). The oil in that state just seemed to take forever for it to drip out but not only at the drain plug but at the oil filter housing as well, perhaps I had never quite gotten all the oil out before and I could have still waited longer but as it was I waited well over 3 hours. I think next time if I have the time I will do an experiment by dropping the oil and lets say leave the pan under it for 15 minutes, then switch to another pail and let it drip out overnight and measure how much more oil comes out. So this time and yes I ended up getting it just over the full mark as I was experimenting with trying to get the level to the add mark after I had run it and then waited some and then added a bit and waited for a certain amount of time for it to settle to the add mark. I very well may not have waited long enough for that experiment but I got to the add mark, then dumped in a full quart and waited some and checked and then waited some more and it crept up more ... and then finally oops, it was slightly over full some hours later when it really had settled all it would. I find this engine sure takes time for the last bit of oil that gets poured in to finally make its way into the crank case. I can only guess at how much too much I added as per maybe a 1/10th of a quart. I had poured in 8.5 quarts going by the quart containers as per 8 quarts and 16 us ounces. I was shocked at how much this was off compared to the prior oil changes and if those larger jugs and they are not marked accurately enough or they contain slightly more than what they say, or the drain time factor made that much of a difference. But I know on this forum there have been others who have said they have put well over 8 quarts in their L8T and now I have also going by the Amsoil true quart containers. Its a confusing convoluted mess up here in Canada with some oil manufactures packaging is in true US quarts, some is also in true US quarts containers on an even number of quarts but also marked in liters which becomes the odd ball volume of a fractional amount of liters. Then there is the Liters only containers, no US markings as its a true metric container and only measured in Liters to an even number of Liters. But remember we used to have Imperial Gallons and Imperial quarts as well !. 
    • Holy smokes. Clearly not a deal on that truck. I just mean in general, matte or painted trim is becoming more normative than chrome, but I know the Black Optics packages on various vehicles are being sold as uplevel trims. They look really good, but sheesh. It's just paint and plastic.
    • I Wouldn't Know Where to Begin    Oh I know where I would begin but I'm just one of over eight billion people on this rock. Eight billion versions of where the goal post is. How large it should be. How far to kick from. What ball is the right ball. Elevation. Age.....are you getting the point? It isn't about disagreeing with one individual. It's about agreeing only with one individual. One's self.   Agreement comes when multiple people hold the same point already. THAT is the goal of an education. Building the Social Contract. That thing that allows us to all read this sentence. We've agreed on the alphabet and how to arrange those letters into words we agree upon whose meanings hold true for everyone entering into that contract. Those words arranged into a sentence form an idea and several sentences strung together in a paragraph convey an argument for or against or inform the reader of a state, condition or perhaps reveal a things nature. Paint a word picture. Make oneself known.    This contract is not limited to words although they are often explained by words. Things like numbers and their usefulness. Physics, Chemistry, Medicine, Music, Art and so on.    The frequency of middle C (C4) is 261.63 Hz is a first principle. We build on that to make music we all can enjoy even if we all can not compose or play. You don't have to master it to make it enjoyable and useful.    So why is the Beginning so difficult? Why is agreement so elusive?   Everyone "Signs" the contract (when receiving that education in obtaining it)  but fewer and fewer in this world have any intention of living by that contract. They find exploiting that contract more advantageous. Disruption. With intent. Without intent. In Ignorance. In your face. With a double dog dare you. With a hold my beer. In resistance to that contract and in spite how it looks on us. It permeates the very air we breath.    In this way the contract is subject to advantage. Abide by it when it serves you, disregard it when it doesn't. Unpredictable and self-serving. Corrosive.....Toxic........   It says a lot about a persons character to disregard the contract, the truth, first principles. None of it good.        ********************************************************   https://medicine.yale.edu/news-article/character-vs-personality-who-we-are-and-who-we-aspire-to-be/   Just an interesting article.   
    • It costs $5,250 for the Yukon Nightfall option (black wheels, emblems and illuminated black GMC grill badge). What a "deal". 
    • I keep getting the above error message on my 25 Sierra.  If I reset the infotainment unit (via the phone hang up button) it will work again for a day or 2.   But I dont want to do have to reset  all the time. Works fine in my 2023 Corvette. On both vehicles I connect wirelessly.   I have a Google Pixel 10 Pro XL, phone is up to date.  Any Ideas.  See attached  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...