Jump to content

What have you done to your K2 today?


Recommended Posts

Waking Pepper from her winter slumber. Battery Tender off, fluids & pressures checked. It sunny out if but brisk and time for first drive of the year. Still allot of snow cover but the roads are salt free. It's suppose to get into the 60's over the next week. Yippie!! 

  • Like 1
Link to comment
Share on other sites

16 hours ago, 15bronzeduramax said:

Latest Mod.. Added OE Yukon/Escalade ambient floor lighting.. These lights stay on while driving and are the same light as the roof console center light..

I followed the install process here....

2015 Silverado OEM Footwell Lighting - YouTube
 

 

IMG_20210303_182547936.thumb.jpg.60887717a6bd136fecd39864eb61949a.jpgIMG_20210303_182626076.thumb.jpg.692a8c9045f285c2410c73e7f3b3a879.jpgIMG_20210303_182630478.thumb.jpg.055116cc4967ddf6351fbaa84f1883f5.jpgIMG_20210303_182558772.thumb.jpg.be85f3575ef33e73919fbe929d9597e3.jpg2143000804_IMG_20210222_145615923_HDR-Copy.thumb.jpg.6da2436f75dfcce31fe08fc940c86be3.jpg

Hello,  How difficult is to put these lights?  is plug and play with the harness from Harness Dr.?

Link to comment
Share on other sites

5 hours ago, Darthmalo said:

Hello,  How difficult is to put these lights?  is plug and play with the harness from Harness Dr.?

It really wasn't hard at all, I had it done in about 2 hours,. minus the prep time of getting the leads ready, that was a couple hours... I bought (4) OEM GM leads off of eBay. P/N 12085535, or you could get them from @pgamboa Harness Dr.. I rough measured from the mounting location to about the gas pedal area, cut some 18 gauge wire (red/black), and heat shrink butt connected them to the GM leads then wrapped each one up good in harness tape.. I mounted all the lights (there are factory mounts in the trucks, except for the passenger seat, it's not a power seat) , I then ran both back seat light wires under the seat rails and up along the inside edge of the console. I took both passenger and driver's side light leads and ran them up to the front of the console up by the console mounting bracket..

I cut back all the black leads and terminated them with a 10mm electrical connector and mounted the negative to a dash mounting bolt that had enough bolt threads to get the terminal, lock washer and a nut on.. I then cut all the positive leads back and connected them all together. I took a piece of wire long enough to reach from the BCM to under the console. Butt connected all 4 leads to the single lead and wrapped that up good with harness tape. I used a T-tap on the violet/green wire in the video and ran the line to that...

Edited by 15bronzeduramax
punctuation and revision
  • Like 1
Link to comment
Share on other sites

0d2db16b80f2a6141735d6f2bb839167.jpg
Finally got around to wrapping my intake tube with some DEI heat wrap. So far it’s about 10degrees cooler driving around in the city. Doesn’t get as much heat soak from the fan kicking on and off.
I can probably get even better IAT if I make a lid for my “box”.


Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites

Got most of my sponsors decals on today ,....







[emoji857][emoji857][emoji857][emoji857][emoji12][emoji12][emoji12][emoji12][emoji24][emoji24][emoji24]
I wish .
Some hate them I kind of like them.

Got it all cleaned up too.[emoji41]12a47aecdff9030398cb33d0d4a7de54.jpg18ee565858e93884494e8bf1884136fd.jpg

Sent from my Pixel 3 using Tapatalk

  • Like 2
Link to comment
Share on other sites

Wasn't today, haha, but just got an oil change for the truck, full synthetic. About 5.5k miles since my last one. Doing a tire rotation tomorrow since that is a little overdue. Very excited for the warm weather coming up, deep cleaning time! 😁

Link to comment
Share on other sites

Ten weeks in zero weather and she popped off like it was shutdown 30 seconds ago. Fueled her up and let her have her head for a few hours. Sweeeeeeeeeeeeet. 
What did you expect?
It's a Chevy. [emoji16]


Sent from my Pixel 3 using Tapatalk

  • Like 5
Link to comment
Share on other sites

Got most of my sponsors decals on today ,....







[emoji857][emoji857][emoji857][emoji857][emoji12][emoji12][emoji12][emoji12][emoji24][emoji24][emoji24]
I wish .
Some hate them I kind of like them.

Got it all cleaned up too.[emoji41]12a47aecdff9030398cb33d0d4a7de54.jpg18ee565858e93884494e8bf1884136fd.jpg

Sent from my Pixel 3 using Tapatalk



What size tires and lift here?


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

My truck suffered an awesome dent. [emoji852]

Well that sucks ass. Was that your neighbor?

Don't take me wrong and I hate to say it though, you left your truck in a vulnerable position. I never park in front of a driveway just for that exact reason.

I over think stuff like that[emoji3166].

Let's see a pic of the carnage.

 

 

Sent from my Pixel 3 using Tapatalk

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.