Jump to content

Recommended Posts

Posted

The K02s must be wider in 275/70 than the old KOs because they don't look as skinny as the KOs I had in the same size.

 

Surprised they rubbed because some are running them on stock trucks.

Yeah, they definitely look wider on the 9" wheel. I was also surprised about the rub. It was very minor only on right turns. Very weird.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

05c8d1f5dd4d73d829531ec23a83563a.jpg23428391eff9739db74c8edfd48e3e9d.jpgb95e6fd775714ab65cb4bcae36483ad6.jpg

 

Pro Comp Rockwell 18x9, 0 offset on 275/70/18 KO2's. Had minor rub when turning right so I folded the carpet liner back and it is gone. Next week replacing Rancho Quicklift with Kings and Cognito UCA's.

 

 

Sent from my iPhone using Tapatalk

I really dig your set up man, those wheels look so cool [emoji41]

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

RC 2.5" Leveling Kit

285/65/20 Nitto Terra Grappler G2

Stock 20" All-Terrain Wheels

 

 

 

where did you get those front mud flaps, i like them, nice and low profile.

Posted

I would say maybe a little louder on the highway, but even then I found myself really trying to notice a difference.

Also this tire is much wider than my KO2s, so going to hum just a bit more I would think. Still yet to drive them off-road or uphill gravel but looking forward to comparing [emoji41]c3ba29640149da84bfb12d39a100e08a.jpg4936fc8456d7a7f9e07ab7291b7cf64d.jpge960ea4f7cb7bd661cbe6e50b9ee8fdf.jpg

what or how did you do to the headlights?looks good
Posted

Welp, wheels and tires came in today, but one of the wheels was damaged by FedEx...looks like I have to wait a couple more days to get them on!!! UGH!

 

1307_zpsigzldoze.jpg

 

1303_zps4jt0gy4g.jpg

 

1305_zpsmuihev8i.jpg

Posted

Welp, wheels and tires came in today, but one of the wheels was damaged by FedEx...looks like I have to wait a couple more days to get them on!!! UGH!

 

1307_zpsigzldoze.jpg

 

1303_zps4jt0gy4g.jpg

 

1305_zpsmuihev8i.jpg

That sucks... FedEx around here isn't very good either... I prefer UPS. Hopefully you don't have to wait long.

 

Sent from my Nexus 6 using Tapatalk

Posted

Welp, wheels and tires came in today, but one of the wheels was damaged by FedEx...looks like I have to wait a couple more days to get them on!!! UGH!

 

1307_zpsigzldoze.jpg

 

1303_zps4jt0gy4g.jpg

 

1305_zpsmuihev8i.jpg

That sucks dude but it'll be worth the wait, those wheels look sick.

 

 

Sent from my iPhone using Tapatalk

Posted

what or how did you do to the headlights?looks good

I baked them and opened them, sanded all the chrome and painted black, then clear coat. Replaced stock projector with 2.5" fxr. Probably my favorite mod, right up there with the wheels and tires
  • Like 2
Posted

Welp, wheels and tires came in today, but one of the wheels was damaged by FedEx...looks like I have to wait a couple more days to get them on!!! UGH!

 

1307_zpsigzldoze.jpg

 

 

 

What are the specs for those tires?

Posted

Im thinking about doing a fabtech 6" lift.. I have a '15 crewcab 4x4 z71 with factory 22" sye/sey wheels.. Id like to just throw some 35" toyo open country at2 tires on the factory gmc wheels..

 

like this guy did..

 

anyone do this? anyone know this members sn? i grabbed the pics a while back and forgot to message the guy. trying to see if they rub bad and if you have to cut everything up?

 

uE6V8zi.jpg

Pretty sure that's jonboy77's truck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • 3.41 Kroger’s in Montgomery TX
    • I really wanted to go to the Fox 2.5's But they were like ~$1,500 vs ~$425 for the Bilsteins. And my research on FOX shocks was that they do not have a great reputation for longevity. I am sure they the FOX's are fantastic, but I know from experience the Bilsteins are rock solid for at least 150k miles. 
    • Conditions for Meeting a Cold Start   The ignition voltage is between 10 and 15 V. The barometric pressure (BARO) is more than 75 kPa. The engine coolant temperature (ECT) at start-up is less than 42°C (108°F). The intake air temperature (IAT) is between 2–32°C (36–90°F). The engine is OFF for greater than 6 hours or the following conditions must be met: The start-up IAT minus start-up ECT are within 12°C (22°F). The start-up ECT minus start-up IAT are within 50°C (90°F). Fuel level is between 25 and 75 %.   Circuit/System Verification Verify that all I/M System Status indicators report YES, and that no I/M Test DTCs are present.If any I/M Test DTCs are set Refer to Diagnostic Trouble Code (DTC) List - Vehicle. If no I/M Test DTCs are set All OK. Inspection/Maintenance (I/M) System Set Procedure   Warning: Refer to Road Test Warning. Note: Do NOT touch the accelerator pedal until told to do so. A change in TP Sensor angle or an increase in engine speed may invalidate this portion of the test.   Note: An I/M Test DTC will not be stored or erased from the ECU except at the end of trip processing, which occurs 5 s after ignition OFF.   Ensure that the vehicle meets the conditions for a cold start listed above. If the EVAP I/M System Status indicator displays NO, perform the EVAP Service bay test if applicable. Turn OFF all of the accessories; HVAC system, other electrical loads, including aftermarket/add-on equipment, etc., and open the hood.   Set the vehicle parking brake and ensure the vehicle is in park for automatic transmission or neutral for manual transmission.   Start and idle the engine for 2 min.   Close the hood, release the parking brake and Accelerate at part throttle to 72–80 km/h (45–50 mph) with this speed maintained until the engine reaches operating temperature, 8–10 min.   Continue operation under these conditions for an additional 6 min.   Accelerate at part throttle to 90 km/h (55 mph) with this speed maintained for 2 min.   Release the accelerator pedal for at least 10 s. This will allow the vehicle to enter the decel fuel cut off.   Safely stop the vehicle, with the engine in drive for automatic or neutral with the clutch pedal depressed and parking brake applied for manual. Allow the vehicle to idle for 2 min.   Shift the vehicle to park for automatic and neutral for manual. Turn OFF the ignition and exit the vehicle. Do NOT disturb the vehicle for 45 min.   Observe the Inspection/Maintenance (I/M) System Status with a scan tool. All of the I/M System Status indicators should display YES.   If the EVAP I/M System Status indicator displays NO, turn OFF the ignition, ensure that the vehicle meets the conditions for a cold start, and repeat steps 6-11 three more times, or until the EVAP I/M System Status indicator transitions to YES. If the indicator continues to display NO, refer to the Inspection/Maintenance (I/M) System DTC Table to identify the DTCs that did not run.   If any of the I/M System Status indicators display NO, refer to the Inspection/Maintenance (I/M) System DTC Table for the indicator which did not display YES. The I/M System DTC Table identifies the DTCs associated with each I/M System Status Indicator.   Observe the I/M Test DTC information with a scan tool. Verify there are no I/M Test DTCs present. If an I/M Test DTC is set, diagnose the DTC using the Diagnostic Trouble Code (DTC) List - Vehicle and refer to Inspection/Maintenance System Check.   Observe the engine DTC information with a scan tool. Verify no DTCs are present. If a DTC is set, diagnose using the Diagnostic Trouble Code (DTC) List - Vehicle. After repairs, perform the Inspection/Maintenance Complete System Set Procedure to verify no further DTCs are set.       Looks like one procedure to me.  Repeated as necessary.
    • My 2020 AT4 6.2 has had the valve spring issue addressed at ~200 miles, front cover/pump replaced at 18k, water pump at 34k and idler pully at 65k.  I would agree with ditching by 100k unless you elect to go with upgraded hardware...say built 10l80 and an lt4 or l8p swap.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...