Jump to content

ATTENTION anyone with oil pressure issues

curtmerci
 Share

Recommended Posts

thilton19 Enthusiast

thilton19

Posted
Posted

I wish I had seen this a few months ago. Had this very same issue while driving home to DE from NYC. Oil pressure took a nose dive and I was still 60+ miles from home on the NJ turnpike. Very high pucker factor!

 

Question, is this something that happens frequently? How often should the screen be replaced?

  • Replies 140
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

curtmerci
curtmerci

For those of you that have noticed oil pressure drops, etc. There IS a screen below the oil pressure sending unit that does become clogged!! I have an 07 GMC Sierra, 4x4 Crew Cab, SLE2 package, 144,0

carnau
carnau

Here is a video I just made with the proper way to fix this concern. Hope this helps.    

BREW154
BREW154

Here is the update. Took my truck to a friends garage over the weekend and pulled the sending unit and installed new. It definitely had gunk and debris in the screen. We went ahead and changed the oil

Posted Images

SierraHD17 Senior Enthusiast

SierraHD17

Posted
Posted

Seems to still be confusion here on issues with these trucks regarding the oil pressure sending unit screen. 

 

First and foremost let's clarify which engines have the screen below the oil pressure sending unit.  In short it's only on engines equipped with active fuel management.  In the full size trucks that equates to any 5.3 in a GMT900 bodied truck from 2007 through 2013(LY5, LH6, LC9 etc).  Otherwise it would also be present in the L76 6 liter trucks as well as the L94 equipped 6.2 powered SUV's and the oddball hybrids 6 liter (LFA or LZ1).

 

  Regular L92 or L9H 6.2's, the LY2 or L20 4.8 or the LY6 and L96 in the HD trucks do NOT have the screen under the sensor.

 

Furthermore no GMT800 truck (1999 through 2007 classic) has the screen as those are Gen 3 engines and this pressure sender screen is a Gen IV thing only as outlined above.

 

 

  • Like 1
jfath14 Enthusiast

jfath14

Posted
Posted

I have the same issues but I pulled my sending unit and the screen was fine. It looks like I have leaky valve seals. I burn quite a bit of oil. Especially in colder weather when the metals seem to shrink a bit. 

carnau Enthusiast

carnau

Posted
Posted
On 3/5/2019 at 9:42 AM, jfath14 said:

I have the same issues but I pulled my sending unit and the screen was fine. It looks like I have leaky valve seals. I burn quite a bit of oil. Especially in colder weather when the metals seem to shrink a bit. 

Just because the screen looks fine doesn't mean the trash didn't sink back down. Check out my video and see how to fix it for good.

 

 

  • Like 1
  • 1 month later...
99GMCZ New Member

99GMCZ

Posted
Posted (edited)

Can anyone tell me if there is some kind of fail safe for low oil pressure on a 1999. GMC Sierra 5.3?? I was driving on the interstate when it cut off on me and I couldn’t get it started back up. Wouldn’t even attempt to turn over. I know there was plenty of oil in it(just added and checked before I got on the road). Right before it died my oil pressure dropped to 0 and my DID said low oil pressure. TIA

Edited by 99GMCZ
Misspelled
  • 2 months later...
Jim1977 New Member

Jim1977

Posted
Posted

Seems like most relavent place to ask this.

I have an 07 classic that the oil pressure gauge is always pegged at 80 psi until you floor it, then it goes to 0 and get a warning chime. Let off the gas, pressure goes back to 80 psi.  I replaced the stepper motor in the cluster and it had no effect.

I also have an 05 yukon denali that does the exact same thing , low oil pressure warning chimes all the time when driving. Oil sending unit on this one was changed about a year ago, but not the stepper.

 

Any ideas? Thanks

 

carnau Enthusiast

carnau

Posted
Posted
On 6/26/2019 at 7:02 PM, Jim1977 said:

Seems like most relavent place to ask this.

I have an 07 classic that the oil pressure gauge is always pegged at 80 psi until you floor it, then it goes to 0 and get a warning chime. Let off the gas, pressure goes back to 80 psi.  I replaced the stepper motor in the cluster and it had no effect.

I also have an 05 yukon denali that does the exact same thing , low oil pressure warning chimes all the time when driving. Oil sending unit on this one was changed about a year ago, but not the stepper.

 

Any ideas? Thanks

 

More than likely it is just the oil pressure sensor. You don't have the filter under the sensor on the old body style but the sensor is in the same place and the replacement is the same minus the filter. Look at the video above. Still blow the passage out to make sure nothing is clogging it. 

 

On 3/6/2019 at 5:59 PM, carnau said:

 

 

 

 

Jim1977 New Member

Jim1977

Posted
Posted

Seems like most relavent place to ask this.

I have an 07 classic that the oil pressure gauge is always pegged at 80 psi until you floor it, then it goes to 0 and get a warning chime. Let off the gas, pressure goes back to 80 psi.  I replaced the stepper motor in the cluster and it had no effect.

I also have an 05 yukon denali that does the exact same thing , low oil pressure warning chimes all the time when driving. Oil sending unit on this one was changed about a year ago, but not the stepper.

 

Any ideas? Thanks

 

Jim1977 New Member

Jim1977

Posted
Posted

I guess maybe the denali could have gotten a faulty new sensor. Or wasn't cleaned out enough.

Going to follow video advice, and blow out the tube .

 

  • 1 month later...
Farley_shawz Enthusiast

Farley_shawz

Posted
Posted

Soooo, the oil pressure isn’t low, the sending unit is just not seeing full pressure because of the screen? Can you just remove it with a pick or something and pop in the new screen or is it more involved then that? If so I’m gonna order a screen and swap it out in like 15 min. 

carnau Enthusiast

carnau

Posted
Posted
On 8/9/2019 at 12:52 AM, Farley_shawz said:

Soooo, the oil pressure isn’t low, the sending unit is just not seeing full pressure because of the screen? Can you just remove it with a pick or something and pop in the new screen or is it more involved then that? If so I’m gonna order a screen and swap it out in like 15 min. 

Watch my video above.

  • 1 month later...
  • 4 weeks later...
Fisherguy58 Enthusiast

Fisherguy58

Posted
Posted (edited)

Carnau, watched the video you posted, thank, might come in handy in the future.  Just kinda crappy you have to keep this whole thing in the back of your mind in case this problem pops up when you're on the road somewhere.

Have you done the job?  Someone earlier in this thread mentioned using a regular deep socket but the guy in the video says you need a special one?   I'd think a regular 6 point socket would work..?

Edited by Fisherguy58
nqabigt Enthusiast

nqabigt

Posted
Posted (edited)
On 3/6/2019 at 5:59 PM, carnau said:

Just because the screen looks fine doesn't mean the trash didn't sink back down. Check out my video and see how to fix it for good.

 

 

much thanks for that video !! had 20psi hot idle now 38

Edited by nqabigt
spelling
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Paid $2.72 for E85 today.
    • Atlas
      Gas Prices

      By Atlas · Posted

      Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • scotthvac.net
      2022-24 halogen - led grille swap

      By scotthvac.net · Posted

      2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
    • davester
      Replacement Radiator

      By davester · Posted

      And use RA's 5% discount code if you buy from them.  google for the code, one is always available.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...