Jump to content

Recommended Posts

Posted
1 hour ago, Donstar said:

Stock tire on a  factory 20" wheel is 275/55/20.  I think this is a comfortable riding and good looking tire size. 

I have that exact size with black factory wheels. They do look good, but "comfortable" is not the word I would use. Passable fits better but they run smooth without vibration and handle well enough at 32 to 33 PSI. Any more pressure than that and it gets to riding like a buckboard. 

 

wheel.jpg

  • Like 1
Posted
Stock tire on a  factory 20" wheel is 275/55/20.  I think this is a comfortable riding and good looking tire size. 


Looks is what gets everyone into hating their ride. My truck came w 22”’s, had dealership downgrade to 20”s then had to order new rims, made the mistake going back to 20”’s cause they look good but wish I had gone to 18”’s just more side wall would give me smoother ride and more sidewall protection too. 20”s tow less too.


Sent from my iPhone using Tapatalk
  • Like 1
  • Thanks 1
Posted
I have that exact size with black factory wheels. They do look good, but "comfortable" is not the word I would use. Passable fits better but they run smooth without vibration and handle well enough at 32 to 33 PSI. Any more pressure than that and it gets to riding like a buckboard. 
 
wheel.thumb.jpg.06c9c829af0988490ab56295d788d9d9.jpg

Absolutely agree


Sent from my iPhone using Tapatalk
Posted

To the OP: wheels and tires are cool and some are really sharp, but if you go bigger/taller it will show up in less responsiveness. It just takes more energy to turn bigger meats. I would look into a lot of the suggestions here on tuning to get more out of the engine. These Gen V engines are pretty good across the board. Somebody out there must have something for the 4.3.

Posted (edited)

A lot of good and bad info I'm hearing. IMO spending thousands on forced induction or gearing to change your stock truck into something it is not is a huge mistake. If you want the bigger engine trade that sucker in and apply those thousands to get what you want. Tuning and CAI is cheap stuff that can wake up a sleepy machine. 6 or 8 speed trannies are the secret sauce that avoids having to do these more expensive add on's. The trans multiplies power and the tune optimizes shifting the available gears to get you there.

 

If you do want to tow be aware a tire with E load rating will handle the load better and I know for michelins can be aired yup to 80PSI if need be to safely carry a load. And they will have less rolling resistance than a smaller heavier mud tire so more MPG.

Edited by Pearl2017
  • Thanks 1
Posted
7 hours ago, newdude said:

 

Performance/speed shop.  https://www.procharger.com/      https://www.procharger.com/dealer-locator   It would take some custom work to get the 5.3 kit I'd imagine to work.  We've got a place up here in NY that would be great at making that type of thing happen.  https://www.berg-racing.com/ 

 

Custom tune.  Never out of the box plug in tuner.  BlackBear Performance, or a local LS/LT engine specialist. 

So the out of the box tuners aren’t worth it? I’m sure I’ll have to rely on a experienced tech somewhere to help but I was hoping some of these new plug in programmers were easier to use now. I’ll definitely look into the tuning to E85 and possibly 4.10 gears or 3.73...

Posted
1 hour ago, Pearl2017 said:

A lot of good and bad info I'm hearing. IMO spending thousands on forced induction or gearing to change your stock truck into something it is not is a huge mistake. If you want the bigger engine trade that sucker in and apply those thousands to get what you want. Tuning and CAI is cheap stuff that can wake up a sleepy machine. 6 or 8 speed trannies are the secret sauce that avoids having to do these more expensive add on's. The trans multiplies power and the tune optimizes shifting the available gears to get you there.

 

If you do want to tow be aware a tire with E load rating will handle the load better and I know for michelins can be aired yup to 80PSI if need be to safely carry a load. And they will have less rolling resistance than a smaller heavier mud tire so more MPG.

Right now I have some 275/55/20s. I switched from the small factory 17s hoping to get a better and sportier ride and look. I ended up getting a rougher ride over 70mph on the interstate! I’m definitely opting for a 2.5” leveling kit so when I get some better tires, they don’t rub. I see know that I need a taller tire. My old ram that I used to have was all ready for me with the Hemi and Laramie 4x4 Edition. I’m just chasing some extra HP to get me through a couple of years. 

028ECB78-B7F9-497E-A114-3E9925FE5862.jpeg

98CCF52E-3D2D-4C3B-8A72-E72C4B0D1664.jpeg

Posted
12 minutes ago, TomBrady80 said:

So the out of the box tuners aren’t worth it? I’m sure I’ll have to rely on a experienced tech somewhere to help but I was hoping some of these new plug in programmers were easier to use now. I’ll definitely look into the tuning to E85 and possibly 4.10 gears or 3.73...

There’s a procharger place about 80 miles away in Decatur, Al! I’ll call them up. Thanks

Posted
3 hours ago, TXGREEK said:


Absolutely agree

Sent from my iPhone using Tapatalk

I once thought that 20's with a 55 aspect would be like wagon wheels until I experienced my daughter-in-law's Yukon XL and my son's High Country both with factory 20's.  I believe premium quality highway tires on 20's will give a nice ride and wouldn't hesitate to have these on my own truck.  Unfortunately, changing tires and wheels is not as simple as  trying on shoes. I was able to try the different sized rims with similar tires on similar vehicles.  If I relied solely on what I read and didn't have this recent experience I too would be anti-20".

Posted
I once thought that 20's with a 55 aspect would be like wagon wheels until I experienced my daughter-in-law's Yukon XL and my son's High Country both with factory 20's.  I believe premium quality highway tires on 20's will give a nice ride and wouldn't hesitate to have these on my own truck.  Unfortunately, changing tires and wheels is not as simple as  trying on shoes. I was able to try the different sized rims with similar tires on similar vehicles.  If I relied solely on what I read and didn't have this recent experience I too would be anti-20".


I’ve got the 16 Yukon XL, wife loves it but did notice harsher ride once I got ride of the factory tires and then put these Michelin Defenders on, they’re 27/55/20. I’d like to change them but what’s a better tire?

dc3bb945b1bcd19534f52f33c81290a4.jpg

My 18 GMC Sierra 6.2 rides on 275/60/20 and rides harsher with new BFG KO2’S. Need the AT’s cause I’m off-road in grassy areas often.

b9d5382ff9beaa2e4b1b2bff1a8bc725.jpg



Sent from my iPhone using Tapatalk
  • Like 1
Posted

Btw, both vehicles aired at 35 psi


Sent from my iPhone using Tapatalk

Posted
1 hour ago, TXGREEK said:

 


I’ve got the 16 Yukon XL, wife loves it but did notice harsher ride once I got ride of the factory tires and then put these Michelin Defenders on, they’re 27/55/20. I’d like to change them but what’s a better tire?

dc3bb945b1bcd19534f52f33c81290a4.jpg

Sent from my iPhone using Tapatalk

 

The harsh ride on this combination surprises me.  Good to know as I thought this would be the ideal wheel and tire!  I believe my positive experience on 20's referred to earlier was with Continentals and BF Goodrich highway tires.  I have Defenders on my 17's. 

Posted
The harsh ride on this combination surprises me.  Good to know as I thought this would be the ideal wheel and tire!  I believe my positive experience on 20's referred to earlier was with Continentals and BF Goodrich highway tires.  I have Defenders on my 17's. 

It rode very smooth with the continentals. I’ll let you know once I switch them out.


Sent from my iPhone using Tapatalk
Posted
4 hours ago, TXGREEK said:

 


I’ve got the 16 Yukon XL, wife loves it but did notice harsher ride once I got ride of the factory tires and then put these Michelin Defenders on, they’re 27/55/20. I’d like to change them but what’s a better tire?

dc3bb945b1bcd19534f52f33c81290a4.jpg

My 18 GMC Sierra 6.2 rides on 275/60/20 and rides harsher with new BFG KO2’S. Need the AT’s cause I’m off-road in grassy areas often.

b9d5382ff9beaa2e4b1b2bff1a8bc725.jpg



Sent from my iPhone using Tapatalk

 

They look good! My offset may be throwing it off some though. I’d like a taller tire like that.

6FD513AF-2FA2-4B06-A6F5-5F0A236113F7.jpeg

EBC1ACA1-55C5-463A-B73F-39ABAEABEFC9.jpeg

Posted
8 hours ago, TXGREEK said:

 


Looks is what gets everyone into hating their ride. My truck came w 22”’s, had dealership downgrade to 20”s then had to order new rims, made the mistake going back to 20”’s cause they look good but wish I had gone to 18”’s just more side wall would give me smoother ride and more sidewall protection too. 20”s tow less too.


Sent from my iPhone using Tapatalk

 

Thanks! Yeah once I hit 70mph the truck is shaking so bad..... 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I have a 2000 Silverado 1500 LS, whenever I put it into reverse and also in drive it clunks, the truck also feels sluggish when driving. Any advice/ideas ?
    • Looks like it's riveted to me. What is wrong with that 1? Welcome to the Forum!
    • Missing pieces of the Assembly   Detergency vs Solvency   Not the same thing. Detergency is the mechanism that surrounds solid particulates preventing amalgamation. Usually accompanied by a Dispersant whose job it is to keep those encapsulated particles in Suspension. Solvency keeps things that can be dissolved in solution.    Salt is a solid that can be dissolved. Pepper is a solid that cannot be dissolved. A detergent/dispersant is effective on pepper but a solvent is more effective on salt. As long as the solids remain in either state, dissolved or dispersed then they can be be removed with the oil upon change.    How many wranglers does it take to herd cats? Depends on how many cats your herding. How much sponge does it take to soak up water? How much water is there to soak up? Point is most oil blends start with some herding ability and next to zero sponge and recently even fewer wranglers are being sent to do the same job.    So you start with a dozen cowboys and zero cows but at the drive progresses you pick up cows along the way, but not cowboys. At some point you have more cows that the wranglers can handle and some leave the herd. Deposits. And the API has an acceptable number of cows they are willing to let loose. In the ideal world zero is the right number for he rancher but to the butcher....a few lost is fine. This cow is beat to death. Let's move on....   Solvency isn't something oils on the Walmart shelf care about AT ALL. Problem is, you motor does. Fuels driven varnish sticks rings and only a solvent can keep them in check. The bet is that the solids driven portion that plug the expander rings and the oil drain backs and VVT screens and AFM screens will be an issue long before varnish is. Not that it wont be but if they market well enough the consumer can be kept ignorant enough to either believe it is "normal" (A quart in 1 or 2K is normal) OR is kept at bay longer than the first owner is likely to hang on to the unit. Solvency cost money.    Now the OEM's have John Q. Public buffaloed into the belief that the number cows accumulated along the trail is a known and predictable CONSTANT. It isn't. Nor is the rate at which they crossed paths with them. Only the number of wrangles is constant. Or was. Each new generation of oil sees fewer and fewer of them.    So what happens when the number of cowboys is lower (lower TBN) with each seasons trail but the trial is longer (OCI) and the number of cows along that trail continues increase? (Conditions that promote deposits).    For awhile the blenders were on to something. Better bases are harder to degrade (fewer cows) but that was overtaken by a longer trail (OCI) and improved breeding (More cows) while continuing to reduce the cowboy staffing levels (TBN/Aniline #).    Marketing has been successful. We've fired most of the staff, cows breed line bunnies, the trail is ten times longer and we've convinced the boss his ranch is in better shape that it ever was.    That kids is just the cleaning side. The side few pay attention to.     
    • Mann+Hummel since 1941 per their web site 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...