Jump to content

Show Us Your 2019 & Up T1 Pictures !

Sierra Dan
 Share

Recommended Posts

  • Replies 3.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bowtie2007
bowtie2007

Finally arrived! Pacific Blue Sierra

Sotally Tober
Sotally Tober

Here is our new 2019 Silverado RST.  For details on all the modifications, here is a link to my build thread:    

z1boss
z1boss

Picked up my special ordered 2019 Trail Boss about 2 weeks ago.  Loving it so far.  Lots of mods already.

Posted Images

camjr Enthusiast

camjr

Posted
Posted

I picked this up last Saturday.  2021 GMC Sierra 1500 Elevation 4x4, X31 package, 3.0l Duramax, Cayenne Red tintcoat.

 

 

GMC1.jpg

GMC2.jpg

  • Like 1
black00ta Enthusiast

black00ta

Posted
Posted

Not new to the forums just new to this section 🤪

Just picked up my 2021 Denali 3.0 Duramax yesterday, traded in my 2015 LT Z71 CC. Love this new truck. 
 

it’s crazy the trade in value on trucks right now, it was too good of a deal to pass up!

F79F0EC6-14F7-4745-BDC7-3006EC6A62EF.jpeg

  • Like 1
drivebydawg New Member

drivebydawg

Posted
Posted (edited)

Hi guys - new to the forum.  Here is my 2021 AT4 with the Go Rhino RB20's installed.  I put them on "backwards" but I may reverse them back to regular orientation.  I can't decide.  My uncle is a GMC/Chevy dealer and I was fortunate enough to get one of the last available trucks with the full technology package.  

 

This one replaced a 2018 Sierra that had KO2's and a leveling kit.  More mods to come.  

 

 

D0BC90B1-012C-4CC8-8266-2CA1C66C3374.heic

Edited by drivebydawg
PureZ71 Enthusiast

PureZ71

Posted
Posted

Really happy I went with the bronze wheels with a blue truck

 

WT7AM5j.jpg

  • Like 1
mdf21 Enthusiast

mdf21

Posted
Posted

Traded in my 2018 GMC Sierra SLT (w/ Denali grille) for a 2021 GMC Sierra Denali.  Dealer gave me more than what I paid for the '18 a year and a half ago so it was hard to turn down.  Loving the new 10 speed.

 

Scheduled the window tint this week.  Kept my Ridge Grapplers from the 18 and will swap at some pint. Probably end up doing a level kit along the way as well. 

 

530282360_2021-06-2809_37_23-Photo-GooglePhotos.thumb.png.ab72e07fa0d894ca3c9e76c0ff4ab16c.png160359305_2021-06-2809_36_38-Photo-GooglePhotos.thumb.png.a1daee3828f7b08da53b37b392e92507.png616436306_2021-06-2809_36_23-Photo-GooglePhotos.thumb.png.c54fe3cf512fa4b1581591ae18613649.png

  • Like 1
Recneps Enthusiast

Recneps

Posted
Posted

Out with the old and in with the new. Great truck but they offered me $5k more than I paid for it after 30k miles. I wanted some of the extra safety features on the ltz. Very happy with my decision even though it’s probably a wash. 

1B3E7959-4FE4-4C7C-8A9E-5B36F563FE75.jpeg

  • Like 1
bluemonstercali Enthusiast

bluemonstercali

Posted
Posted

I thought I'd throw this out there since I looked alot prior to matching my satin steel metallic fender flares and found nothing. 

20210702_121149.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...