Jump to content

LED Light Bar Installation Options

pcontant
 Share

Recommended Posts

pcontant Enthusiast

pcontant

Posted
Posted (edited)

Just got 2019 Sierra Elevation. Looking at options to install a 20 or 22” LED light bar. Had one in my bumper opening on my 2012 2500 HD and found it indispensable for night time driving in the backwoods.  Has anyone installed one yet?  Share your pictures of your setup if you have. 

 

Thanks!

Edited by pcontant
  • 5 months later...
pcontant Enthusiast

pcontant

Posted
  • Author
Posted

After months of waiting for a company to make brackets or someone to share ideas on a led bar install, I finally installed one today.  (Auxbeam 22” Curved) I cut a hole in the lower bumper plastic, made simple brackets, wired a relay (with freewheeling diode) off the high beams and voilà!!! The Sierra lights are very poor, especially in high beam - the lights create a blacked out horizontal band that drives me crazy.  Not anymore. 

A4CD7472-73F8-444F-B9E5-76E5A4D662C0.jpeg

1B5B251D-9522-4771-937D-250CBF834A06.jpeg

  • Like 2
jordanl010 Enthusiast

jordanl010

Posted
Posted (edited)
18 hours ago, pcontant said:

After months of waiting for a company to make brackets or someone to share ideas on a led bar install, I finally installed one today.  (Auxbeam 22” Curved) I cut a hole in the lower bumper plastic, made simple brackets, wired a relay (with freewheeling diode) off the high beams and voilà!!! The Sierra lights are very poor, especially in high beam - the lights create a blacked out horizontal band that drives me crazy.  Not anymore. 

A4CD7472-73F8-444F-B9E5-76E5A4D662C0.jpeg

1B5B251D-9522-4771-937D-250CBF834A06.jpeg

 

Where did you wire your switch for this light bar? Or is it ran off your high beams? 

Edited by jordanl010
pcontant Enthusiast

pcontant

Posted
  • Author
Posted

Ran relay control off my high beam and ran the relay control ground into the cab incase I want to have high beam without the led bar. 

5662E330-A25A-49FD-9FCE-78FD86AAAA40.jpeg

PabloK Enthusiast

PabloK

Posted
Posted

I'm going with a Rigid Industries SAE compliant 20 or 30 inch.

 

1.15 inches tall.  higher end setup...

 

https://www.rigidindustries.com/sr-series-20-dual-function-sae-auxilary-high-beam-driving-lights-920413.html

 

 

otherwise.... i would wait and let the market mature and catch up....  still lots of manufactures designing 2019 specific systems...

 

here's one for chevy that's very clean...

 

https://www.roughcountry.com/chevy-led-grille-kit-70817c.html?gclid=CjwKCAjwtuLrBRAlEiwAPVcZBilzSWGsteTAICdb4PmgnQ7U1L2hXBulORJ01Zqml9CgUXUfN0cfJhoCLLgQAvD_BwE&find=2019-gmc-sierra-1500-4wd-381260&sid=TfQY3m53yw

 

  • Like 1
  • 2 weeks later...
PabloK Enthusiast

PabloK

Posted
Posted
On 9/12/2019 at 8:15 PM, pcontant said:

Nice light (RIGID) but too expensive for me. I really like that RC Chevy setup.

yea RC setup is clean.

 

RI is big money... agree...  quality is there though..  

 

  • 4 months later...
2k19Sierra Enthusiast

2k19Sierra

Posted
Posted
On 9/7/2019 at 10:04 PM, pcontant said:

After months of waiting for a company to make brackets or someone to share ideas on a led bar install, I finally installed one today.  (Auxbeam 22” Curved) I cut a hole in the lower bumper plastic, made simple brackets, wired a relay (with freewheeling diode) off the high beams and voilà!!! The Sierra lights are very poor, especially in high beam - the lights create a blacked out horizontal band that drives me crazy.  Not anymore. 

A4CD7472-73F8-444F-B9E5-76E5A4D662C0.jpeg

1B5B251D-9522-4771-937D-250CBF834A06.jpeg

Any chance you have some photos of the brackets you made and where you mounted them too?  This looks to me like the best place for a light bar on these trucks but nervous about cutting into the bumper...

  • 5 months later...
Guyat4 New Member

Guyat4

Posted
Posted

Did you have to remove the plastic piece that was cut out to mount the light? Or can I cut out with it on the truck. I have a 2020 GMC At4 and would like to mount the same light as you did.

 

Thanks!

  • 1 month later...
EXSlider400 Senior Enthusiast

EXSlider400

Posted
Posted (edited)

Does anybody know of any aftermarket inserts made for light bars? Apparently we cannot order the bumpers off the Harley edition trucks.

9F4FE138-6D0B-474A-AB65-93A5845C5BD3.jpeg

B539F83C-DEEF-499C-86F1-0EA17B412FA4.jpeg

Edited by EXSlider400
pcontant Enthusiast

pcontant

Posted
  • Author
Posted
On 7/26/2020 at 3:00 PM, Guyat4 said:

Did you have to remove the plastic piece that was cut out to mount the light? Or can I cut out with it on the truck. I have a 2020 GMC At4 and would like to mount the same light as you did.

 

Thanks!

I cut the opening without removing anything.  Worked out well!

  • 2 years later...
  • 3 years later...
GregB65 New Member

GregB65

Posted
Posted

Does your truck have the Duramax 3.0?  I am wanting to do the same thing, but understand that this opening is for cooling the engine.  If you do have the 3.0, has your truck run any hotter?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Thanks - I wasn't quite caffeinated this morning. 2:1 makes sense, turning the crankshaft 360 degrees will turn the cam 180 degrees, and had I done that, the cam's dot would be at 6 and the crank's at 12 again.   I went ahead and took the sprocket off anyway, aligned everything dot-to-dot including the balance shaft just for s&g. I'm glad I did because I discovered no Loctite on the timing sprocket bolts. Maybe it's not required, but at only 20 ft-lb torque spec, those bolts aren't in there very tight. Cleaned and reassembled with some thread locker and torqued.   A general observation: Less is more with RTV. If a little doesn't stop a leak, a LOT probably won't, either. RTV is thinly veiled revenge, in a tube...      
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...