Jump to content

Towing Pics

Maize & Blue
 Share

Recommended Posts

ForkliftJeff Enthusiast

ForkliftJeff

Posted
Posted

Love how this truck pulls my little trailer. Much better than my 08 Dakota. No problems up those steep canyon roads. 

34324C5D-AEF6-47AA-A8D4-D380B1F7845B.jpeg

A12518C2-B6D6-4A4E-903E-56DB302D8021.jpeg

  • Replies 283
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Limelight
Limelight

You win the entire internet for towing the entire house.  Lolol

eppieguy
eppieguy

Nothing, it’s not a T1.

gothp28
gothp28

8k and 27ft. Did a good job Sent from my SM-G965U using Tapatalk

Posted Images

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
On 7/3/2020 at 5:49 PM, ForkliftJeff said:

Love how this truck pulls my little trailer. Much better than my 08 Dakota. No problems up those steep canyon roads. 

34324C5D-AEF6-47AA-A8D4-D380B1F7845B.jpeg

A12518C2-B6D6-4A4E-903E-56DB302D8021.jpeg

Very nice set up, my neighbor to the north.

 

Gray clouds look very familiar?

ForkliftJeff Enthusiast

ForkliftJeff

Posted
Posted
1 hour ago, JimCost2014 said:

Very nice set up, my neighbor to the north.

 

Gray clouds look very familiar?

Thanks. It was raining so hard that day. Helped in washing the winter grime off the trailer though. 

madconcept Enthusiast

madconcept

Posted
Posted

Brought our 24’ Travel Trailer home from my dad’s farm.  New truck tows like a champ.  Has the max trailering option.

Levelling kit on truck causes a bit of squat though even with a WD hitch.

May need air bags to compensate for level kit.

1E716721-ABB3-4897-A17D-D103B3ED7991.jpeg

ForkliftJeff Enthusiast

ForkliftJeff

Posted
Posted
1 hour ago, madconcept said:

Brought our 24’ Travel Trailer home from my dad’s farm.  New truck tows like a champ.  Has the max trailering option.

Levelling kit on truck causes a bit of squat though even with a WD hitch.

May need air bags to compensate for level kit.

1E716721-ABB3-4897-A17D-D103B3ED7991.jpeg

Do you have any adjustment left in your WDH? Maybe one less chain link on your bars would get you level? 

madconcept Enthusiast

madconcept

Posted
Posted (edited)
6 hours ago, ForkliftJeff said:

Do you have any adjustment left in your WDH? Maybe one less chain link on your bars would get you level? 

No my torsion bar height seems maxed out.  Tried going up another chain link but it’s too tight to lift it into place.
 

And yes the jack is up a couple inches above the wood blocks in the pic, looks like it may be touching lol!

 

The rear sag isn’t too bad.  From fender to tire is 5 1/2” up front and 4” at the back.  Unloaded I’m about 6” front and back, with levelling kit.

At the end of the day if you want to tow with a levelling kit, plan to install air bags I suppose.

Trucks come out of the factory with a natural rake to compensate for loading.

 

586E7ACC-6AA7-4BB5-8818-D6A4B9DFDFDE.jpeg

Edited by madconcept
ForkliftJeff Enthusiast

ForkliftJeff

Posted
Posted
47 minutes ago, madconcept said:

No my chains are maxed out.  Tried going up another link but it’s too tight.
 

And yes the jack is up a couple inches above the wood blocks in the pic.

 

The rear sag isn’t too bad.  From fender to tire is 5 1/2” up front and 4” at the back.  Unloaded I’m 6” front and back, with levelling kit.

At the end of the day if you want to tow with a levelling kit, plan to install air bags.

Trucks come factory with a natural rake to compensate for loading.

 

586E7ACC-6AA7-4BB5-8818-D6A4B9DFDFDE.jpeg

Right on. I’ve had a few friends who were “told” how to setup their WDH but didn’t know there was some adjustment to dial it in perfect. 

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
12 hours ago, ForkliftJeff said:

Thanks. It was raining so hard that day. Helped in washing the winter grime off the trailer though. 

Yea, know what you mean on both, it had rained the last 6 weekends in the Seattle area before this one.

Greyhound6.2 Enthusiast

Greyhound6.2

Posted
Posted (edited)
3 hours ago, madconcept said:

No my chains are maxed out.  Tried going up another link but it’s too tight.
 

And yes the jack is up a couple inches above the wood blocks in the pic.

 

The rear sag isn’t too bad.  From fender to tire is 5 1/2” up front and 4” at the back.  Unloaded I’m 6” front and back, with levelling kit.

At the end of the day if you want to tow with a levelling kit, plan to install air bags.

Trucks come factory with a natural rake to compensate for loading.

 

586E7ACC-6AA7-4BB5-8818-D6A4B9DFDFDE.jpeg

Try to tilt the WDH head down you should be able to loosen the bolts, add a shim or washer between the head and shank to gain some additional leverage on the WDH spring bars you should be able to get more weight transfer to the front wheels.  

Edited by Greyhound6.2
madconcept Enthusiast

madconcept

Posted
Posted
1 hour ago, Greyhound6.2 said:

Try to tilt the WDH head down you should be able to loosen the bolts, add a shim or washer between the head and shank to gain some additional leverage on the WDH spring bars you should be able to get more weight transfer to the front wheels.  

Thanks.  I just adjusted the tilt by adding another washer.  Don’t think there’s enough room left on the shank to add anymore so I think that’s all I can do.
Hopefully my truck doesn’t drive all squirrelly!

Big/only reason I was able to get this truck because I promised my wife it would handle our TT better than my old truck lol!

I’m hoping I don’t have to go out and get airbags now!

 

Love how the truck looks unloaded with the level kit though!

 

1AF1B322-4645-4F2A-9CCD-174D885A8ED4.jpeg

corn18 Enthusiast

corn18

Posted
Posted

What's interesting about your picture is that your shank seems to be angled up.  Is there a lot of play in your shank when in the receiver?  I had that problem on my 2008 Tundra.  The whole WDH would tilt up because of the loose fit in the receiver.  Then I had to add a lot of washers (head angle) to get the WDH set up properly.  I added a thin shim to the shank to make it tighter in the receiver.  Then I honked down so hard on the WD bars that I bent the receiver on the Tundra.  Oops.  

Greyhound6.2 Enthusiast

Greyhound6.2

Posted
Posted
55 minutes ago, corn18 said:

What's interesting about your picture is that your shank seems to be angled up.  Is there a lot of play in your shank when in the receiver?  I had that problem on my 2008 Tundra.  The whole WDH would tilt up because of the loose fit in the receiver.  Then I had to add a lot of washers (head angle) to get the WDH set up properly.  I added a thin shim to the shank to make it tighter in the receiver.  Then I honked down so hard on the WD bars that I bent the receiver on the Tundra.  Oops.  

Mine does that what kind of shim did you use? 

killramos Enthusiast

killramos

Posted
Posted (edited)

AD23B88B-D0E3-48EE-83E9-B88A66DC8A37.thumb.jpeg.dd97160a2cde13322743a5f5a4a889b8.jpeg

 

Not the greatest pic but borrowed my brothers car hauler to move furniture to my new house. Don’t do much towing (none) but she did it like a champ even when loaded right up.

 

Pretty happy with the sag even with the off road suspension. Didn’t even have the equalizer bars installed since I was pulling through the inner city. 

Edited by killramos
nick242 Enthusiast

nick242

Posted
Posted (edited)

Picked up a new trailer and heading out tomorrow. I have adjusted the saddles for the WD hitch up two holes. Bars have lots of tension but assume it’s the leveling kit on the truck preventing me from getting it level with the trailer. Not the end of the world....
 

0C47CD55-2E4A-4F93-A65A-363D1415E56A.jpeg

Edited by nick242

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,942
    Total Members
    8,960
    Most Online
    tblt44
    Newest Member
    tblt44
    Joined

  • Who's Online   6 Members, 0 Anonymous, 748 Guests (See full list)

  • Latest Articles

  • Posts

    • C/K Man
      Silverado 4500-5500-6500 are they still being produced? Would have sold better as GMCs as well

      By C/K Man · Posted

      There was talk over the last couple of years that the contract to build these trucks between GM and International would not be renewed.  International moved production of all their other trucks besides the companion CV model out of the Springfield plant some time ago when they opened their San Antonio plant.  That left Springfield only building the Silverado Medium Duty, International CV Series, and some Express/Savanna long wheelbase cutaways.  International also put the plant up for sale some time ago.  This all answered my earlier question as to why GM and International did nothing with these trucks since they were introduced, as they had basically become a market 'placeholder' with a finite life.    The Silverado Medium Duty/International CV trucks were interesting combination of a GM powertrain, electrical system, and K2XX Silverado cab with an International chassis that was supposedly designed for a step-van type vehicle they never produced.  They were manufactured in International's Springfield plant along with the IH MV series initially.  When first introduced, there was much talk that the Silverado Medium Duty/CV would eventually get a gasoline engine option along with other upgrades and GM and IH would work on a class 6/7 joint venture truck.  This was before VW bought Navistar out, after that happened no more was said.  Draw your own conclusions...   About the time talk started that the GM/IH joint venture was not going to be renewed, rumors started that GM would develop a new line of medium duty trucks themselves.  The story is the new trucks will be part of the next generation HD's due in 2028, and will still feature a 'straight rail' chassis design that the current medium duty has.  GM views this as a desirable feature that differentiates their truck from the competition.  A gasoline engine option is also expected.  As the current Silverado Medium Duty remains in production until September 2026 and there is still a lot of inventory available do not expect any official word for some time.   I believe GM remains committed to their successful partnership with Isuzu, and all the LCF models will still be available from Chevy Commercial dealers.  Isuzu is on the cusp of opening a new large plant in South Carolina and there is also speculation that this may result in new product for both Isuzu and Chevy Commercial dealers.                  
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • nfisherman
      Software Update

      By nfisherman · Posted

      I have a 2026 2500 HD Ultimate. My phone app says there’s a software update available. It’s something about improved battery management and something to do with the running boards. I follow the instructions for the update but the “Check for Updates” option is greyed out in my settings menu. Has anyone else seen this? How did you resolve it? The help message just says “see your dealer” if the download doesn’t work. I’m just trying to save a trip. 
    • newdude
      Exhaust Question

      By newdude · Posted

      Fuel mileage?  That's all how you use your right foot.  Exhaust will give you sound.   Stock exhaust 5.3 is 2.75" diameter piping.     If the truck is nice and worth putting some $$ into it, I'd go for a Corsa catback.  I had one on my 2019 old body 5.3 and it was just perfect.  Zero drone, just driving around and cruising on the highway you'd think it was stock, but when you opened it up it was like a Camaro with the factory dual mode.  Corsa bumps their catback to 3in diameter.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...