Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

Pig Sooie 4 Enthusiast

Pig Sooie 4

Posted
Posted
7 hours ago, malibu43 said:

I am also interested with this same question. I have a two inch front leveling kit with 295/55/20 Ridge Grapplers and it sits perfect but if i have anything in the bed of my truck i notice it squats. Any 1 inch rear blocks worth having?

 

I'm curious about this as well. My truck sits perfectly level with a 2" kit up front. But on uneven ground or with any load in the back I get some squat. I added Hellwig 990 helper springs, and they definitely improved the ride with a load, but didn't get rid of the squat like I expected.

 

I was toying with the idea of going .5 or 1 inch higher with a block in the back. Didn't see any blocks for a .5 inch lift though...

20200606_165627.jpg

 

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

Rockboyz New Member

Rockboyz

Posted
Posted

Hey Guys,

New to the forum. So in brief, I recently picked up a 14 Sierra SLT, All Terrain. The rake is driving me crazy, so I ordered the Rough Country 2" leveling kit. Watched a bunch of videos on the install. My question is for those of you who have installed this kit, or looked at this kit,  I see the reason to having to disassemble half the suspension is because of the shaft being in the way of dropping the one bolt down in from the top. Looking for opinions on cutting that bolt to length, so it doesn't hit the shaft, and installing it from the bottom. Thoughts on strength issues? I mean in theory, the strut doesn't know which direction the bolt is in? Correct?? I greatly appreciate your feedback! Thanks guys! pics to follow! 

Bensjamming Enthusiast

Bensjamming

Posted
Posted
3 hours ago, Rockboyz said:

Hey Guys,

New to the forum. So in brief, I recently picked up a 14 Sierra SLT, All Terrain. The rake is driving me crazy, so I ordered the Rough Country 2" leveling kit. Watched a bunch of videos on the install. My question is for those of you who have installed this kit, or looked at this kit,  I see the reason to having to disassemble half the suspension is because of the shaft being in the way of dropping the one bolt down in from the top. Looking for opinions on cutting that bolt to length, so it doesn't hit the shaft, and installing it from the bottom. Thoughts on strength issues? I mean in theory, the strut doesn't know which direction the bolt is in? Correct?? I greatly appreciate your feedback! Thanks guys! pics to follow! 

I did the proper way and put them both in from the top, mainly so if a nut should come off I wouldn't lose the bolt out the bottom and cause major havoc. It took me about 20 minutes per side and that was doing it myself. Its not hard at all to do it that way. I think from looking back at it that you could possibly even skip the upper ball joint and get it in by unhooking the tie rod and just sharply turning the hub to move the shift out of the way. Even with separating the UBJ it only took about 45 minutes start to finish for it all, including putting the tools away.

malibu43 Enthusiast

malibu43

Posted
Posted (edited)

Now that I have my 2" level installed, I've been shopping casually for tires/wheels online and looking at other trucks out on the road and in parking lots.  I was doing some work on the truck last weekend and had the back end lift up so there was almost no weight on the wheels, so the frame and body were several inches higher than normal.  My wife came out and said "when are you going to do that to your truck?"  "Lift it like that?" I asked.  "Yes, that's what I thought you were going to do.  You should do that."

 

So my wife planted this idea about going up higher and now I'm starting to agree.  I started looking at 3" front and 1" or 2" rear leveling kits with control arms.  I watched a youtube video and didn't realize how easy the control arm swap is if you're already in there doing a leveling kit. So while the 2" level was fun and got my feet wet, I'm thinking now I may want to go a little bigger.

 

A couple of questions:

1.  With a 3" front level and new control arms, how big can I go with tires?  Does that allow you to go bigger than 33" (305's)?

2.  Everyone seems to be sold out of control arms right now...?  Which are the best to go with (assuming they are available)?

3.  What would be the "next level" after a 3/1 or 3/2 leveling kit and control arms?  Shock upgrade?  At what point should I consider that vs level kits?

Edited by malibu43
RJ3 Enthusiast

RJ3

Posted
Posted

Where is the best place to buy leveling kits and shocks ? 

malibu43 Enthusiast

malibu43

Posted
Posted
On 7/28/2020 at 1:18 PM, malibu43 said:

Now that I have my 2" level installed, I've been shopping casually for tires/wheels online and looking at other trucks out on the road and in parking lots.  I was doing some work on the truck last weekend and had the back end lift up so there was almost no weight on the wheels, so the frame and body were several inches higher than normal.  My wife came out and said "when are you going to do that to your truck?"  "Lift it like that?" I asked.  "Yes, that's what I thought you were going to do.  You should do that."

 

So my wife planted this idea about going up higher and now I'm starting to agree.  I started looking at 3" front and 1" or 2" rear leveling kits with control arms.  I watched a youtube video and didn't realize how easy the control arm swap is if you're already in there doing a leveling kit. So while the 2" level was fun and got my feet wet, I'm thinking now I may want to go a little bigger.

 

A couple of questions:

1.  With a 3" front level and new control arms, how big can I go with tires?  Does that allow you to go bigger than 33" (305's)?

2.  Everyone seems to be sold out of control arms right now...?  Which are the best to go with (assuming they are available)?

3.  What would be the "next level" after a 3/1 or 3/2 leveling kit and control arms?  Shock upgrade?  At what point should I consider that vs level kits?

Bump...

 

I guess everyone's out driving their trucks instead of reading forums...?

langston1726 Enthusiast

langston1726

Posted
Posted
Bump...

 

I guess everyone's out driving their trucks instead of reading forums...?

 

I’ve been running a 3” level up front with forged Rough Country upper control arms for almost 20000 miles now and have had 0 issues. I’m running a 315/70/17 BFG KO2. (Not a big rim guy) I did have to do some trimming to keep it from rubbing. I would think a 305 would fit fine as long as you don’t go crazy with negative offset. My rear is stock with Bilstein 5100s. My front is about 0.5 higher then the rear but very hard to notice most of the time. I don’t tow anything either.

 

3” is the max I would go. Anything beyond that is probably asking for problems. I would definitely replace your UCAs. The stock ones will be struggling. I also have some Kryptonite outer tie rods sitting in the garage. Just haven’t had a chance to put them on yet.

 

 20349edf1a392020d6c9ecfe9d92441c.jpg

 

f90108261fe1d87e88c8510fa5accc40.plist

 

 

Sent from my iPhone using Tapatalk

mrhonestlyinsane Enthusiast

mrhonestlyinsane

Posted
Posted

Malibu, 

You have 500 pages of people that have a difference of opinion. 

If you or only doing a level going to 3 " will stress your ball joints.  Hence the reason for the upper control arm. The ride will suffer . It will make it more stiff. The lower control arm will sit at an angle during the resting position . It will put stress on the CV joint and lower ball joint as well. 

When I had my 2010 I ran a 2 inch level for 5 years even that made the ride more stiff. When I bought my 2014 I ran the same 2" level and put 275/65r20 Duratracs technically 34.1" tire on with stock rims. It barely rubbed the wheel liners and I just tied them back. 

Wasn't happy with it and went to a 5 inch lift. 

 

Alot of people will tell you different things. 

Personally I wouldn't do a 3" level. 

Like I mentioned before everyone has their own opinion and money  and skill set weigh into it. 

 

 

malibu43 Enthusiast

malibu43

Posted
Posted
5 hours ago, mrhonestlyinsane said:

Malibu, 

You have 500 pages of people that have a difference of opinion. 

If you or only doing a level going to 3 " will stress your ball joints.  Hence the reason for the upper control arm. The ride will suffer . It will make it more stiff. The lower control arm will sit at an angle during the resting position . It will put stress on the CV joint and lower ball joint as well. 

When I had my 2010 I ran a 2 inch level for 5 years even that made the ride more stiff. When I bought my 2014 I ran the same 2" level and put 275/65r20 Duratracs technically 34.1" tire on with stock rims. It barely rubbed the wheel liners and I just tied them back. 

Wasn't happy with it and went to a 5 inch lift. 

 

Alot of people will tell you different things. 

Personally I wouldn't do a 3" level. 

Like I mentioned before everyone has their own opinion and money  and skill set weigh into it. 

 

 

Thanks for your input/opinion.

 

I did read most of this thread several months ago when I decided to do my 2" level, but I mostly soaked up info related to the mod I was looking at at that time.  Hence, me just posting a question about a 3" level or additional upgrades, rather than reading the entire thing again.

 

Again, thanks for the input.

malibu43 Enthusiast

malibu43

Posted
Posted
12 hours ago, langston1726 said:

 

I’ve been running a 3” level up front with forged Rough Country upper control arms for almost 20000 miles now and have had 0 issues. I’m running a 315/70/17 BFG KO2. (Not a big rim guy) I did have to do some trimming to keep it from rubbing. I would think a 305 would fit fine as long as you don’t go crazy with negative offset. My rear is stock with Bilstein 5100s. My front is about 0.5 higher then the rear but very hard to notice most of the time. I don’t tow anything either.

 

3” is the max I would go. Anything beyond that is probably asking for problems. I would definitely replace your UCAs. The stock ones will be struggling. I also have some Kryptonite outer tie rods sitting in the garage. Just haven’t had a chance to put them on yet.

 

 20349edf1a392020d6c9ecfe9d92441c.jpg

 

f90108261fe1d87e88c8510fa5accc40.plist

 

 

Sent from my iPhone using Tapatalk

Thanks for the response, and especially the pics!  Your truck is actually very similar to where I'm hoping to take my truck (even same color), and it's been hard to find pictures of the look I'm going for (including black bowtie and grill mesh), so you posting them has really helped me see what it might look like when it's done.

  • Like 1
Built2crash Enthusiast

Built2crash

Posted
Posted

Just to contribute to the post, my experience with leveling kits:

 

My 2013 Silverado had a 2" RC Leveling kit in it and I ran 32.5" BFG TKO2, all other components were stock.  I ran that truck for 50K miles before I upgraded. I had zero problems with that setup.

 

I just recently put an Eibach Pro Level kit in my 2016 GMC Sierra. that kit includes 4 new shocks and spring up front. I'm running that on the 2.5" lift setting. I have stock 18" rims with 285/65/18 BFG TAKO2 on it (32.5" tire). I'm sure I can fit 33" tires on it no problem and I'm pretty sure I could fit 33.5" with no or maybe minor trim. Also, all other components are stock. Will post pictures soon.

 

My brother in law has a 2018 sierra we put a 2" RC spacer in it with 33.5" BFG TAKO2's, did the nor Cal mod on it and they fit fine. We actually did the Nor Cal mod prior to testing the tires out so I cant say if they would have rubbed without the mod or not, I think they would have rubbed just eyeballing it.

 

In all these cases the ride quality was basically the same with the level kits installed, My eibach setup is better ride quality.

 

Conclusion: IMO and as others have said, stay at 3" or less for a level to save your components. Otherwise, spend the money and go 5" or 6" lift kit, this allows you to run a larger tire and saves your components and ride quality.

 

Hope this helps

 

 

Danyoda Enthusiast

Danyoda

Posted
Posted

My 2018 Sierra has a 2.5 inch level and I’m running 315/70/r17 (metric size of 35/12.5) with very and I mean very little rub on the felt liner on the back side of the wheel well. 

RJ3 Enthusiast

RJ3

Posted
Posted

Anyone know why the ready lift leveling kit won’t work with stock Z71 shocks ? 

jimbrown1 Enthusiast

jimbrown1

Posted
Posted
31 minutes ago, RJ3 said:

Anyone know why the ready lift leveling kit won’t work with stock Z71 shocks ? 

Where did you read that?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Newduramaxh*ar
      DTC P2C48 auxiliary cooling pump

      By Newduramaxh*ar · Posted

      I tried tapping it.  This might sound like a dumb question, you should feel vibration or some type of noise when it turns on? Can someone please verify? Thank you all!
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      I feel better now for my own view point and actions or lack there of towards the dealership service theme reading your post and others. GM corporate is who offers the two free oil changes on the HD trucks and I bought my truck in Feb of 2025 and those oil change offers run out within 2 years I believe and I highly doubt I will be using either one of them. I had asked if I could officially give those free services to another customer ( a friend ) and they said no, its all a GM corporate thing based on the vehicle in question. What that service advisor did however was go into a little story about how such and such customer was denied engine warranty because he had done his own oil changes because then they are not documented ... you see where that goes and so an employee playing the game of scaring the customer into having the service work done there most certainly triggered my thought process. At a later date I did talk to the person who handles warranty claims at the dealership and she said to be sure to document the oil changes and keep receipts for the oil and filter ( coped the receipts from cases of Mobil oil and case of filters I bought from them ) and the vehicles VIN, the date of service, mileage etc and staple that together as a record I would give them if that was ever needed and I keep my own log book for services for each vehicle as well. Oh and about 8 months after I bought the truck the dealer starts calling me to offer a maintenance service since they haven't seen my vehicle show up on their system ... for the mere fee of 300.00 Canadian to change the oil and rotate the tires and a few other minor checks and I declined the offer, I get the call again a couple of months later for the same thing and she could tell I was not interested and she asked if they should take my name off the call list and I said yes, do that !.    By the way did you happen to keep your factory oil filter to open it up and see the surprises inside as I expect some will show up as per the odd little sliver of metal shaving and particles that the filter does trap along with bits of grey silicone sealer that come off of the inside edge of mating surfaces. I have cut open every filter so far on my truck although few miles but have changed the oil often and the second filter was vastly better with very little of anything, that first filter was the unsettling one as I expected it would be. 
    • OnTheReel
      OCI, not when but why?

      By OnTheReel · Posted

      I get why they do this…but man…not ideal. I only extract on inboard boat engines because the drains are buried and even then I hate it because it’s easy to leave a quart behind with that method.   They should market it as an “oil refresh” not oil change!
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      I only get oil changed where I can watch. Valvoline pulls through the dipstick into a see thru glass. When done they show me the dipstick. About the only way they can mess up is using the wrong oil. But that secret wouldn’t stay secret long. Honda uses TQ wrenches on everything. You can watch through a plate glass window. Discount tires does that with tires. Trust but verify. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I would not argue that with you. It would be pointless to argue against the truth and you speak the truth.    My question and in fact the entire point of this thread is an exploration into the levers of wear which happens no matter how well we maintain our powertrains.    Some of these levers we exert a good deal of influence over which can and do result is lower wear, longer powertrain life. Some others we are sort of stuck with.    An engine is typically done when the ring to bore seal no longer is able to do the job effectively. Normally the first thing to go in a engine otherwise well maintained and adult driven is this seal.    Looking into the means, methods, products and attitudes that influence the rate of wear seems a worthwhile inquiry to me.     

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...