Jump to content

Cannot enter keyless entry programming mode

JakesInSpace
 Share

Recommended Posts

JakesInSpace New Member

JakesInSpace

Posted
Posted

Truck in question: 2001 Silverado 1500 LT Z71 (w/ Stock Keyless Entry System)

 

Okay, I really didn't want to make a forum post, but I've scoured the hivemind for answers and I have found none.

 

Recently I ordered new batteries for my 15732803 key fob that was showing signs of a weak battery. i.e. Required holding button longer than before, and requiring me to stand closer.

 

I removed the old battery about 12 hours before installing a new one. (idk why I did this, but I didn't think it would cause issues.) I tested the fob at Pep-Boys on one of those Energizer fob testers. Seems to work fine!

 

After installing the battery, I followed the instructions on the inside of the fob case. "Press and hold LOCK & UNLOCK for 7 seconds". I did this, but I received no response from the truck. I tried this several times to no avail. At this point I assume that removing the battery for an extended period caused the rolling codes to become lost or out of sync... I begin attempting to enter programming mode as per my trucks service manual.

 

This is where I am having problems. I followed the service manual and a multitude of other online resources that gave me the same, or slightly differing instructions. However, the locks NEVER cycle when I release the drivers-side UNLOCK button. I tried different combinations of this, with different speeds; removing the key, opening and closing the door every time. No luck...

 

The systems worked well for years until I removed and replaced the battery.

 

I respectfully ask that you don't respond with programming instruction from the service manual. I've read it so many times I could recite it by memory. I am certain that it's either a hardware/software issue, or it's a process issue. Maybe I'm performing the procedure too fast? Too slow? Are there known quirks that are undocumented in the service manual? Did I somehow mess something up by leaving the fob battery out for so long? (This seems unlikely since the fob isn't the issue in question)

 

Thank you in advance for anyone who responds.

 

tbarn Senior Enthusiast

tbarn

Posted
Posted

I know you said not to but here is the official version from service information. May or may not be different from what you are using. No leaving the battery will not cause an issue. Are you sure you didn't break a solder joint inside the fob while changing the battery. Very common issue.

 

Transmitter Programming Procedure (Method 1 - No Tools Required)
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the door unlock switch.
  4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation.
Booger T Enthusiast

Booger T

Posted
Posted

Had a similar issue on my wife's 2007. Fob quit working, no remote start, no door locks, nothing. Changed battery still nothing. Don't know about on a 2001 but there is a receiver in truck that gets signal from the fob. Same receiver controls all functions from the fob. I had to take to dealer to find solution. Had to replace the receiver and reprogram fob and everything was back to normal.  Just throwing this out as something you might want to check.

JakesInSpace New Member

JakesInSpace

Posted
  • Author
Posted
1 hour ago, tbarn said:

I know you said not to but here is the official version from service information. May or may not be different from what you are using. No leaving the battery will not cause an issue. Are you sure you didn't break a solder joint inside the fob while changing the battery. Very common issue.

Thank you. I have a hot air station and will reflow the fob tonight to see if it starts working.

 

1 minute ago, Booger T said:

Had a similar issue on my wife's 2007. Fob quit working, no remote start, no door locks, nothing. Changed battery still nothing. Don't know about on a 2001 but there is a receiver in truck that gets signal from the fob. Same receiver controls all functions from the fob. I had to take to dealer to find solution. Had to replace the receiver and reprogram fob and everything was back to normal.  Just throwing this out as something you might want to check.

Man, that would sure suck if that's the case... But I will keep that option open just in case I cannot fix it myself. Thank you for your response!

  • 3 years later...
  • 4 months later...
  • 1 year later...
JakesInSpace New Member

JakesInSpace

Posted
  • Author
Posted

I know this is a pretty old thread, but I finally fixed my keyless entry system!

 

Behind the instrument cluster, in the top right corner there is a small black box. This is the keyless entry module. Turns out is was just not plugged in. Just before I originally made this thread I had a mechanic replace my heater core which requires complete removal of the dash. When putting it back together they must have just forgotten to plug it in, or it wasn't secured and came loose.

 

Either way, I just plugged it back in and the truck enters programming mode just fine. Bought a new fob and everything works perfectly.

 

I hope this thread can help some other poor soul who just didn't think to check the connection.

 

 

  • 3 months later...
Oscar55e New Member

Oscar55e

Posted
Posted (edited)

Hello I know this is old but on my 2001 Chevy Silverado I have replaced keyless entry module 3 times no luck when I go to cycle the doors I’ve done everything I could possible search up just need answers 🙏🏻

Edited by Oscar55e
  • 2 months later...
Sierra Spike New Member

Sierra Spike

Posted
Posted

"Programyourremote.com" This website will give you instructions for every vehicle that uses a

Keyless system. Hope you all find what you're looking for. I did !!!

  • 2 months later...
hughrasmussen New Member

hughrasmussen

Posted
Posted

The problem I am having is similar to the original poster.  Please no reposts of the steps.  The problem is that after doing the steps, the system does not respond with the door lock cycling, it is a common problem that none of the "read the service manual instructions" helpers seem to grasp.

  • 2 months later...
davester Senior Enthusiast

davester

Posted
Posted

I would consider replacing the remote module in the truck.  I know on later GMT800's, it's part of the passenger door switch assembly, but IDK where it is on earlier ones.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Yesterday we brought home a 6yr  old Havanese dog from a nearby SPCA.  We've had her for 24 hours and we are delighted with how well she is adjusting to her new home.  It  was a huge decision to adopt a dog at this stage in our lives but we believe we made the right choice!   it was reported that her first 6 years were ones of neglect.  I think she's already realizing her life is going to get a whole lot better...  so is ours!    
    • Hoginedgewood
      2 speed transfer case optional now?

      By Hoginedgewood · Posted

      I thought I was building a HD 3500 srw, maybe I was lost.
    • Coastie05
      Which 2027 engine will you choose?

      By Coastie05 · Posted

      No doubt, I definitely agree with you. However, considering the 6.2 and 3.0 have been catastrophically failing with very little miles, I figured I would put trouble free. I’m at 18,4xx and still not a single issue.  
    • KARNUT
      Slate Electric Truck

      By KARNUT · Posted

      It’s never dry here but it gets hot. My 4 vehicles I keep at home drive an 18 mile loop. One 6 days a week. Two about 3 days each and one once a month. Only one goes on trips about 4 times a year 1000 to 2000 miles each time. One 26 years old gets driven once a month for 22 years. One 14 years old goes 6 days a week. The other two are recent at 2 and 4 years. All are performing normal no extra service other than that would be half of recommended or severe service in the maintenance manual. No extra water or steam out the exhaust or premature plug wear. I would consider an 18 mile loop would be enough. So apparently once a month at 18 miles for 22 years has kept the collector car running well. About 45 minutes a month. 
    • newdude
      Transmission Temperature Hitting 220s

      By newdude · Posted

      It is working as designed.  NHT and non NHT trucks have the same exact transmission cooling setup.  NHT just gets a larger radiator.     The transmission cooler loop on these is as follows.     -Transmission out goes into an oil to water heat exchanger (item #1 in the first illustration below).  This exchanger has engine coolant opposite the transmission fluid and uses engine coolant to warm and then regulate the transmission fluid temperature when its in the operating window.   - From the cooler it goes to a thermal bypass valve (item #11 in the 2nd illustration below).  If the ATF has not reached the temp to open the bypass (194F), it loops back.   - When it reaches 194F, the thermostat opens and ATF then flows out to the oil to air auxiliary cooler (item #17 in the 2nd illustration) at the front of the truck.  From there it goes back to the transmission.     Your only fix would be to swap for the PPE thermal bypass delete block which will open the loop to the aux cooler all the time.  It will STILL run warm, probably 170-200F, but that's as low as you'll get it as its still flowing through the oil to water exchanger.      

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...