Jump to content

High Mileage Tires??

shimmy
 Share

Recommended Posts

shimmy Enthusiast

shimmy

Posted
Posted

I've been a big fan of Michelin tires in the past but the LTX A/T's that are on my 2020 2500HD are a bit disappointing.  I've done some towing with a 8k pound trailer, a bunch of highway, and the rest of local driving and at 28,000 miles, these tires are looking that they need to be replaced.

Can you suggest a mostly highway tire that can get me 40,000 miles??  I'm looking for an all season tire that is acceptable in snow, but that's not my major concern.  I'm running the stock 275-70-18's

 

Thanks in advance. 

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted

Continental

TERRAINCONTACT H/T 

 

Any all season will give better mileage than the A/T's you are disappointed with.

Real trick to long mileage is the alignment and inflation.

IMHO of course. 

😉 

  • Like 1
CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Run the Michelin Defender LTX, those are far more "highway" oriented than the LTX A/T's.

 

Firestone Transforce HT2, Copper Discover AT3 and the Michelin Agilis CrossClimate are my other suggestions.

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted

Michelin Defenders!  They are far more capable off road then their design and primary use suggests.

 

 

  • Like 1
Another JR Senior Enthusiast

Another JR

Posted
Posted

I have Michelins of various types on four vehicles, and have bought well over a dozen sets over the years, and have been very satisfied with them. 
 

That video, though, was pretty lame. The equivalent ad slogan would be “Michelin - It’s a Tire!”

  • Like 1
  • Haha 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted (edited)
1 hour ago, Another JR said:

I have Michelins of various types on four vehicles, and have bought well over a dozen sets over the years, and have been very satisfied with them. 
 

That video, though, was pretty lame. The equivalent ad slogan would be “Michelin - It’s a Tire!”

You are right, I linked to the wrong one.  There's one out there with a whole bunch of Jeep Wranglers going over much more difficult terrain.  Let me take another look...  Nope, can't find it.

Edited by swathdiver
  • Haha 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
11 hours ago, Another JR said:

I have Michelins of various types on four vehicles, and have bought well over a dozen sets over the years, and have been very satisfied with them. 
 

That video, though, was pretty lame. The equivalent ad slogan would be “Michelin - It’s a Tire!”

Found it!

 

Truston Gunter Enthusiast

Truston Gunter

Posted
Posted

I bought some BFG ko2's at 302 miles. Currently at 28K miles and they still look good! Lots of tread, I do some towing, nothing real heavy. 29ft TT that weighs 7500 lbs. Gas mileage totally sucks but I love the aggressive look 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • SFC Retired
      2023 DRW Wheel Liners

      By SFC Retired · Posted

      Did have to make 1 modification because of the WeatherTech rear mud flaps and that was needing 3 longer screws than what came with the install package. 😄
    • SFC Retired
      2023 DRW Wheel Liners

      By SFC Retired · Posted

      Picked up the liners yesterday. Installed passenger side WITHOUT any modifications. All mounting holes lined up perfectly. Rain is interfering today with drivers side. Very Happy! Will add pics when finished
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      As a matter of amusement I’ll leave this conversation with this. Do you beat the government average fuel estimate? Statistics are a guide to me. Not a rule. Someone once said I have to have the last word. If true and possible may be. I’ll blame that on working in a family business.
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That is a fair point, and I agree that trying to log “everything in the truck” would be the wrong direction.   There are a lot of modules and a lot of traffic. If the product became a full-truck datalogger, the amount of data would get huge very quickly, and most owners would never use it.   I think the first useful version would need to be narrow: - powertrain-side event evidence - selected high-value parameters - communication / voltage / reset events - pre/post event window - short report first, raw log only as backup   One distinction I should make is between active OBD/PID polling and passive bus capture. If you are polling PIDs through OBD, then yes: the more parameters you request, the lower the effective sample rate becomes, and you are adding diagnostic traffic to a vehicle that is already busy running itself. With passive CAN capture, the recorder is not asking all the modules for data. It is listening to traffic that is already on the bus. So it does not consume vehicle bus bandwidth in the same way that a scan tool polling hundreds of PIDs would. But your point still applies in a different way.   Even if passive capture does not add bus traffic, the recorder still has limits: - processing rate - storage rate - timestamp accuracy - decoder workload - event filtering - report size - user attention span   So the answer cannot be “log everything and let the user figure it out.” The product would need to store enough raw evidence to be useful, but only decode, graph, and present the important parts around the event.   A practical report should probably show: - what triggered the capture - how much pre/post data was preserved - which selected parameters changed - how those values compared to baseline - whether the same pattern happened before - whether any voltage, reset, bus-off, lost-message, or communication fault occurred - selected graphs around the event - raw data only as supporting evidence   So I agree with you. More data is not automatically better. The real product is the reduction from raw data into a useful event report.
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That makes sense, and I agree with most of that.   I think the product would need both: 1. a default powertrain template, so it is useful out of the box; 2. user-selected priority parameters, so the owner or shop can choose what they want to see first.   Different users are going to care about different things. One owner may care about oil pressure and voltage. Another may care about misfire trend, AFM/DFM behavior, or U-codes. A shop may want communication events and repeatability first. Your baseline point is probably the most important one. Raw data is not very useful unless the report can show what normal looked like for that vehicle under similar conditions.   The way I would think about it is: - start with a basic known-good baseline - learn normal behavior for that specific vehicle over time - allow the event to be overlaid against baseline - show whether the event was a one-time spike or a repeatable pattern - provide a simple severity level, but with clear limits on what that severity means   For example, early severity could be something like: - Info: event captured, no obvious abnormal pattern - Watch: value moved outside baseline, but not repeated - Warning: repeatable abnormal pattern under similar conditions - Critical: communication loss, voltage drop, bus-off, reset, or severe repeated event   I would not want the first version to say “replace this part.” That would be overclaiming unless there is repair-confirmed data behind it. It would be more honest to say “this pattern deserves inspection.”   On the OBD port question, I think OBD absolutely has a role. OBD is probably the right place for: - DTCs - freeze frame - VIN - calibration information - normal scan-tool parameters - Mode 6 / enhanced diagnostic data if available The reason I am still looking at an ECM-side recorder is that the failure may happen before anyone connects a scan tool. If the owner plugs in a scanner after the event, the pre-event evidence may already be gone unless the ECU happened to save it. So I do not see this as “OBD versus ECM-side.” I see it more like: - ECM-side recorder: always armed, rolling buffer, event evidence - OBD/DLC companion: DTCs, freeze frame, VIN, calibration, normal scan data - phone/cloud: status, notes, upload, report generation, notifications   I agree that phone connection and push notifications would be useful. I just would not want the phone or cloud connection to be required for capture. The recorder should save the event locally even if the phone is not connected. The phone should help with event marking, download, notes, upload, alerts, and report viewing.   For a default GM V8 event report, would this list make sense? - RPM - calculated load / MAP - throttle position - vehicle speed - gear / torque converter state if available - coolant temperature - oil pressure - oil temperature if available - battery voltage - commanded AFM/DFM state if available - actual AFM/DFM state if available - misfire counters / roughness by cylinder if available - fuel trims - relevant U-codes / communication events - bus-off / lost periodic message / module reset / voltage drop events Which of those would you remove, and what would you add?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...