Jump to content

Recommended Posts

Posted
3 hours ago, swathdiver said:

Yeah, don't buy one.  Get a scan tool with bi-directional communications that was made for your truck.  GMs MDI2 with GDS software and a laptop will allow you to see all the codes and runs graphs and diagnostics and tests and resets, etc. on your truck.

 

Thanks.  I will check it out.

Posted
1 hour ago, 14GMCZ71 said:

 

Thanks.  I will check it out.

Get your checkbook out...$$$$

  • Like 1
Posted
5 minutes ago, Lsgun1 said:

Anyone bought from that vendor before? China car diag....?

I have not but guys from the TahoeYukon forum have bought Tech-2s from them.

  • 2 weeks later...
Posted

Update from my last post on May 14th.  Dealer originally said my 5 year power train warranty was covering the replacement of all 8 injectors.

 

Waited about 5 days and heard nothing back.  Called service writer and was told the injectors would not be covered.  I asked if they could check to see

if the injectors would be covered under my extended warranty - GMPP - GM Protection Plan - which expires in 2021 or 84,000 miles on odometer.

 

They checked and said GMPP is covering all 8 injectors and my deductible is $200.00.

 

Now the dealer did not clear the engine light the second time it came on.  It has remained on - until yesterday - light went off and has not come back on.

 

Waiting to see what happens.  Do these CELs normally go off after a certain amount of time?

 

Truck still runs good - only I notice a sight rough idle when starting truck cold.

 

Purchased truck new in August, 2014.  Now has 30,000 miles.

Posted

When the CEL turns off on it's own depends on the specific problem.  Some problems, like if the MAF sensor is left unplugged, will turn off right away when it's plugged in again, others will need a certain number of ignition cycles without the problem reoccurring before the light goes off, and others will require one or more testing cycles to complete before it goes off on it's own (where the testing cycle may not happen immediately or take some time to complete).

  • 3 weeks later...
Posted

Update from my last post on May 25th.

 

My extended warranty - GMPP - GM Protection Plan - which expires in 2021 or 84,000 miles - is covering the cost of the 8 new fuel injectors less a $200.00 deductible.

 

I dropped my '14 GMC Sierra off at the dealer today at 4:30PM.  Service Rep said I should have it back Thurs. afternoon.  I was informed the 5 Year PowerTrain warranty

does not cover fuel injectors.  FYI only code P050D logged when CEL came on.  No other codes.  Will post again after I get the truck back.

 

 

 

 

Posted

Picked up my truck from the dealer today - Wed, June 12th.  All 8 fuel injectors were replaced.

 

Receipt lists  " INSTALLED 12684125  :SL-N-INJECTOR KIT (0300-CT)  Qty: 8 "

 

My "receipt" lists no numbers for labor, materials, etc. - just says Warranty under Amount.

 

I did get a look at the paper with the total on it - around $1,200.00.  Dealer service rep said something about

their cost billed back to GMPP and my cost without the extended warranty would have been much higher.

 

I paid $200.00 - my extended warranty deductible.  Time will tell if this fix works and keeps the CEL off.

 

 

  • 4 months later...
Posted

I am having the same code and problems with my ‘17 Silverado with the 6.2 with 47,000 miles. Dealership said that the injectors aren’t covered under warranty even though they know they are a problem. How do I get GM to warranty these? 

Posted

Unless you got the letter from gm stating they extended the warranty on the injectors on your specific VIN, plan on paying for them yourself. If you're mechanically inclined do it yourself and save a lot of money. All you need is 8 injectors, which might be hard to find with the strike, 2 high pressure fuel lines and 8 intake gaskets. There's videos on YouTube showing how it's done. It should only take 4 hours or so depending on skill level. Just make sure the holes in the head where the injectors go are clean and free of any burrs.

I replaced my bank 2 injectors last week then had 2 of them fail again this week. Second time took me less than 2 hours. Only thing I can guess is there was something in the hole that nicked the seals and caused them to fail prematurely. Either that of there's something wrong with my engine causing the seals to fail. Both times my injectors failed was on cylinders 4 and 6 which are AFM cylinders which has me thinking there's something deeper going on. I guess we'll see if I can make it more than a week this time.

Sent from my SM-N975U using Tapatalk

  • 1 month later...
Posted

with the P050D code...'16 silverado, ~65k miles, no extended warranty...the CEL has been coming on and off for quite some time...but since i checked it, it has always been the P050D code...first recommendations were to flush with injector cleaner...i have done that a few times...seemed to work eventually...but i am to the point it must be something more...would it be worth changing the spark plugs before i take it to the shop?  that is one of the recommended fixes (and would be MUCH cheaper than injectors) but i dont want to just through away $50-$100 on spark plugs if they arent needed...

 

if not, since i am out of warranty, i dont plan on going to a dealership...plan on going to a regular mechanic...any idea what the damage will be?  sounds like the $1200 mentioned above was internal charges...i'm nervous what the bill might be...

 

this has been the worst chevy (out of three, i have bought each brand new) i have every had...it is frustrating as hell...

Posted

I had that same code but a p0300 also and was started to blow white smoke out of the exhaust. I ended up just paying out of pocket for injectors and fuel lines. It wasn’t worth the fight with GM. My mechanics checked everything else out also. Spark plugs were fouled and the cylinders weren’t washed out with fuel. He changed the oil though and did an upper induction cleaning   I just got the call today that it’s done, a month and a half later, about to write an $1800 check for 8 new injectors, new fuel lines, oil change, and induction cleaning. If you do just the injectors and fuel lines it should be around 1,200-1,400

  • Sad 1
  • 1 month later...
Posted (edited)

What part numbers are you guys getting for the injectors? The ones that came out of my truck are 12668390, dealership said new replacement part was 12684125, but then looks like 12698484 is the newest part. I ordered 12698484 from GM wholesale dealer, box says 12698484 but the injector is stamped 12681212.

 

Seems like a lot of conflicting info on this fuel injector issue..

 

12681212 (that I just got in today) is grouped with 12668390 (that came out of my truck) under the latest replacement number so I'm guessing I can use these. Everywhere is back ordered so I guess I'm lucky I even got these

Edited by Cohen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • 2026 3500HD.  Mostly empty. Grocery getter. What tire pressure are you running for 37x12.50x20. I have 37x12.50R20 Toyo Open  Country RT pro and been running around 55 lbs front and rear and it's too much. Tires are wearing more in the middle. Toyo says 45 front and 50 rear. Chalk test and it's still too much. I lowered it to 40 front 44 rear see what happens. 
    • Enjoy the new truck, it’s a beauty. I’m glad you’re keeping the OBS, I love those old trucks. 
    • With large equipment or deep mud it is more of a use the higher gear to avoid spinning tires, getting stuck because of spinning tires and doing damage to your machine. The idea is if you run out of torque before you spin tires you can still downshift for more torque. If you are just spinning your tires in the lowest available gear you are stuck and things break.   Automatic transmissions, traction control and electronic transfer cases change the calculation a little as you the driver have less control over each piece. 
    • are there any codes? with lots of rust, perhaps disconnect/clean both sides of the connection/examine cable ends (the wires) for corrosion going into the sheath & replace if necessary/reconnect ALL the power AND ground cables between the battery, engine, frame, cab, fuse box and starter charm.li (website) has a no-start diagnostic procedure you can work through to get it working.
    • Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...