Jump to content

Need any ideas 2018 Sierra 6.2.

Brett Boyd

By Brett Boyd
in Troubleshooting & Recalls

 Share

Recommended Posts

Brett Boyd New Member

Brett Boyd

Posted
Posted (edited)

This past Friday morning went and started my truck to get warm came back about 5-10 minutes later with the truck off lights still on and it’s throwing engine reduced power and p0641 code. Truck won’t turn over at all. Any ideas or tips? Thank you in advance

Edited by Brett Boyd
Added tags
JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
56 minutes ago, Brett Boyd said:

Bump

Could be a few different things:

 

What Does the P0641 Code Mean?

Diagnostic trouble code (DTC) P0641 stands for “Sensor Reference Voltage “A” Circuit/Open.” It is logged whenever the PCM detects voltage that does not match manufacturer specifications on the 5-volt reference circuit.

If the 5 volts feeding the three-wire sensors is shorted to ground, it pulls all the three-wire sensor voltages to zero, and on some vehicles (like Fords), it will put the PCM to sleep so that there is no spark, fuel injection, or communication with the scan tool; thus there is no DTC for a shorted 5 volt rail on a system where the ECM/PCM has just one 5 volt rail because the ECM/PCM can’t communicate anyway. 

If, however, there are multiple 5 volt rails, a short on just one of the rails won’t disable the engine. On a Ford, if any three-wire sensor shorts out, it kills the whole system. On a system with multiple rails, only one system goes down, but the engine will still run, albeit in limp mode (usually).

A 2016 Chevy Silverado, for example, has five different 5 volt rails. A short on any of these five rails will cause a different code to be set for each rail. The 5 volt rails on the Silverado each feed a different set of sensors.

Electric transmission control module designed for automatic transmission P0641 code is logged whenever the PCM detects voltage that does not match manufacturer specifications on the 5-volt reference circuit.

Rail 1 feeds the Engine Oil Pressure Sensor, the Fuel Rail Pressure Sensor, the A/C refrigerant pressure sensor, the Exhaust Pressure Differential sensor, the Camshaft Position Sensor. A short on this rail will set code P0641.

The other four 5 volt rails set different codes.

Rail 2 feeds Accelerator Pedal Sensor 2, the MAP sensor, and the Brake Pedal Position Sensor. That rail will set a P0651 if it shorts out.

Rail 3 feeds Accelerator Pedal Sensor 1 and the Intake Air Valve Position Sensor. That rail sets a DTC P0697.

Rail 4 feeds the EGR position sensor. That rail sets a DTC DTC P06A3.

Rail 5 feeds the Crank Position Sensor, The Cooling Fan Speed Sensor, the DEF fluid pressure sensor, and the Turbocharger Vane Position Sensor. That rail sets a DTC P06D2.

For an advanced, technical discussion of two-wire vs three-wire sensors and reference voltage, you can read our explanation here.

Note: The definition of code P0641 may be different depending on the vehicle manufacturer. Consult the appropriate repair manual or repair database for the exact code definition.

What are the Possible Causes of the P0641 Code?

engine control unit or ECU of a car with multicolored wires plug at foreground Wiring or connection issues can cause the P0641 code.

The code P0641 can be triggered by various issues, including:

  • Malfunctioning sensor
  • Wiring or connection issues
  • PCM problems

What are the Common Symptoms of the P0641 Code?

Keep an eye out for these warning signs if you are dealing with a P0641 code:

  • Check Engine Light is illuminated
  • Sensor-related performance issues

How to Diagnose the P0641 Code

Identifying the underlying cause of the P0641 code can be difficult, especially if you’re not confident with your automotive knowledge. In most cases, it would be best to bring your vehicle to an auto repair shop and seek the help of a professional for an accurate diagnosis.

Here is a video that can help give you a better idea of how this trouble code might be diagnosed:

How to Fix the P0641 Code

The P0641 code is a generic trouble code that may apply to various makes and models. While vehicles from different manufacturers may share common symptoms, that doesn’t mean that they also share repair processes. For example, the steps for diagnosis and repair for a P0641 Chevy code may differ from those required by a P0641 Hyundai code.

If you’re an advanced DIYer who’d like to fix this code on your own, it will be helpful to refer to your repair manual or get factory vehicle repair information from an online subscription service.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      "Life is getting back to normal."    I'm driving again and all new joints are operating as expected for this stage of recovery.   My most recent joint replacement still requires a lot of attention but experience has taught me that time will quiet the remaining pain.  I joked with my surgeon that another joint replacement would take my mind off my most recent surgery and he responded by saying the next will be a hip!  There are no plans for another surgery but, unlike me, I don't think he was joking!  I certainly wouldn't refuse further replacement  if required but hope to spend time out of the "post-op"  period.  I can't stress enough that if you have been recommended for total hip, knee or shoulder replacement that you welcome the offer.  Post-op "recovery" may sound daunting and painful, however, this is far better than the insidious erosion of mobility you are currently experiencing.  Imagine what it would feel like to wake up most mornings feeling better and more mobile than you did the previous day!  Prior to my first surgery in June 2025, even getting out of bed was becoming a formidable task.  Since the day after my first surgery, I get out of bed everyday easily and unassisted.  Making the switch to feeling a little better each day rather than a little worse, is hugely motivating!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...